ABAC COOL 250 Refrigerated Air Dryer - 188 PSI Max, R-404A, 230V Single-Phase
| Specifications (As Configured) | |
|---|---|
|
ABAC
|
|
|
4102006322
|
|
The ABAC COOL 250 is a refrigerated air dryer that pulls moisture out of compressed air before it reaches your tools, air lines and finishing work. It is the largest COOL dryer in our range, sized for a shop running a large rotary screw or a duplex piston system, and it runs on 230V 60 Hz single phase power, so it goes in behind a big air system without a three phase feed. It pipes in through 1-1/2 inch NPT female connections and draws 1,102 W.
Key specifications
- Model: COOL 250, ABAC type C9 (part number 4102006322)
- Type: refrigerated compressed air dryer, hot gas bypass design, vertical cabinet
- Maximum working pressure: 188 PSI (13 bar)
- Pressure dew point: 45 F (7 C), held above 32 F by the hot gas bypass so the evaporator cannot freeze
- Power supply: 230V, 60 Hz, single phase
- Nominal electrical power at 60 Hz: 1,102 W total, made up of a 1,007 W refrigerant compressor and a 95 W condenser fan
- Refrigerant: R-404A, 1.05 kg (2.3 lb) charge
- Inlet and outlet connections: 1-1/2 inch NPT female
- Weight: 156 lbs (71 kg)
- Dimensions: 12.2 x 27.8 x 39.1 in (310 x 706 x 994 mm)
- Room temperature range: 41 F to 104 F (5 C to 40 C)
- Incoming air temperature: 50 F minimum, 122 F (50 C) maximum
- Condensate removal: automatic timer drain
- Monitoring: front panel pressure dew point indicator with green target zone, stop and run button
- Brand: ABAC, part of the Atlas Copco group
Typical applications
Paint and body shops, cabinet and woodworking shops, production cells, laser and plasma tables, packaging lines, injection molding, pneumatic control systems, tire inflation benches, and any shop where water in the air line is blowing out finishes, rusting tools and fittings, or freezing an outdoor drop in winter. A refrigerated dryer chills the compressed air so the water condenses, drains it away, and sends dry air down the line, which is the most straightforward way to stop moisture damage downstream of a compressor.
How the COOL range works
ABAC builds the COOL range around a combined air to air and air to refrigerant heat exchanger with an integrated water separator, a hot gas bypass valve that holds refrigeration capacity steady across load conditions and keeps the evaporator from freezing, a capillary tube and refrigerant filter on the cooling circuit, a refrigerant compressor protected against thermal overload, an air cooled condenser, a timer drain that clears condensate on its own, and a front panel dew point indicator with a green target zone so you can read air quality at a glance. ABAC rates the COOL range for a 45 degree F (7 degree C) pressure dew point, which it notes covers more than 95 percent of industrial compressed air applications. The vertical cabinet layout keeps the footprint small and leaves the serviceable parts reachable from the front.
Service and running cost
The COOL 250 carries a sealed R-404A circuit with a 1.05 kg (2.3 lb) charge and draws 1,102 W at 60 Hz, which is 1,007 W for the refrigerant compressor and 95 W for the condenser fan. There is no desiccant to replace and no purge air lost to regeneration, which is the running cost that separates a refrigerated dryer from a desiccant one, so a dryer this size stays cheap to leave running alongside the compressor. Routine upkeep is keeping the air cooled condenser clear of dust so it can reject heat, checking that the timer drain is actually discharging, and leaving clearance around the cabinet for airflow. The hot gas bypass valve is factory set and is not a field adjustment, so a dew point reading outside the green zone usually points to a dirty condenser, a hot room, or incoming air above the 122 F limit rather than to the valve.
Sizing and installation
Size the dryer to the compressor it follows, not to the pipe it bolts into. The COOL 250 sits at the top of the COOL line, intended for shops running a large rotary screw or a duplex piston system that has outgrown a COOL 200, so step up to it when a smaller unit is running at its limit.
ABAC publishes the COOL ratings at reference conditions of 101 PSI (7 bar) working pressure, 95 F (35 C) inlet air and a 77 F (25 C) room, and real conditions move the number. Capacity drops as the room gets hotter and drops harder as incoming air gets hotter, so a dryer sitting in a hot room or close to a compressor discharge will not hold its rating. Higher line pressure works the other way and recovers a little capacity. If the dryer has to live near the compressor, fit an aftercooler ahead of it, keep the room between 41 F and 104 F, and keep incoming air below 122 F and above 50 F. Give the condenser clear airflow and keep the unit out of the heat the compressor throws off.
How it compares and what to pair it with
Pressure rating is the first thing to check against your system. The COOL 125 is rated to 232 PSI, while the COOL 150, the COOL 200 and this COOL 250 are rated to 188 PSI, so if your system regularly sits above 188 PSI, size around that ceiling rather than around flow alone. The COOL 250 is the largest of the three and the heaviest at 156 lbs, on the same 12 x 28 x 39 inch cabinet footprint as the 150 and the 200. All three run on 230V single phase power, so moving up the range does not mean running a new three phase feed.
Pair it with a coalescing filter upstream for oil carryover and a particulate filter downstream when the work calls for cleaner air, and give the condensate somewhere to go. See the rest of the refrigerated air dryer range and our full air dryers lineup, or the rotary screw air compressors and piston air compressors this size of dryer is most often paired with. Call us for the published COOL 250 flow rating and installation clearances before you pipe it in.
NOTE: Actual product may be different from pictured!
Financing Options
Financing Options
We offer Financing Through Many Different Avenues:
- Affirm is great for smaller purchases. You can do this during checkout.
- Clicklease is a great option for Instant decisions up to 25k. NO Hard credit pull. No Time in Business Required. More information can be found out about it here: https://www.clicklease.com/partner/warthog-air-compressor-store
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
AirCompressorStore.com offers a complete selection of air compressors, parts and accessories designed to keep your equipment running reliably and efficiently. Whether you’re servicing a small shop compressor, maintaining an industrial air system, or replacing a worn component in a production environment, our parts are sourced from trusted manufacturers and built to meet the demands of real-world compressed air applications.
