ABAC COOL 200 Refrigerated Air Dryer - 200 CFM, 188 PSI Max, 230V Single-Phase
| Specifications (As Configured) | |
|---|---|
|
ABAC
|
|
|
4102006321
|
|
The ABAC COOL 200 is a refrigerated air dryer rated at 200 CFM, sized to dry the full output of a large rotary screw or duplex piston compressor before that air reaches your tools, air lines and finishing work. It runs on 230V single phase 60 Hz power, draws 922 W, and pipes in through 1-1/2 inch female connections.
Key specifications
- Model: COOL 200 (part number 4102006321)
- Type: refrigerated compressed air dryer, vertical layout
- Air treatment capacity: 200 CFM (5,200 l/min, 312 m3/h)
- Maximum working pressure: 188 PSI (13 bar)
- Pressure dew point: 45 degrees F
- Power supply: 230V, single phase, 60 Hz
- Nominal electrical power: 922 W
- Inlet and outlet connections: 1-1/2 inch F
- Refrigerant: R-404A
- Weight: 130 lbs
- Dimensions: 12 x 28 x 39 in
- Room temperature range: 41 to 104 degrees F
- Maximum inlet air temperature: 122 degrees F
- Condensate removal: automatic timer drain
- Brand: ABAC, part of the Atlas Copco group
Typical applications
Paint and body shops, cabinet and woodworking shops, production cells, laser and plasma tables, packaging lines, injection molding, tire inflation and pneumatic control systems, and any shop where water in the air line is blowing out finishes, rusting tools and fittings, or freezing an outdoor drop in winter. A refrigerated dryer chills the compressed air so the water condenses, drains it away, and sends dry air down the line, which is the most straightforward way to stop moisture damage downstream of a compressor.
How the COOL range works
ABAC builds the COOL range around a combined air to air and air to refrigerant heat exchanger with an integrated water separator, a hot gas bypass valve that holds refrigeration capacity steady across load conditions and keeps constant pressure in the evaporator so it cannot freeze, a capillary tube and refrigerant filter that protect the cooling circuit from debris, a refrigerant compressor cooled by the refrigerant itself and protected against thermal overload, an air cooled condenser with a large exchange surface, a timer drain that clears condensate on its own, and a front panel dew point indicator with a green target zone so you can read air quality at a glance. ABAC rates the COOL range for a 45 degree F pressure dew point, which it notes covers more than 95 percent of industrial compressed air applications.
Service and running cost
There is no desiccant to replace and no purge air lost to regeneration, which is the running cost that separates a refrigerated dryer from a desiccant one, so a dryer this size stays cheap to leave running alongside the compressor. Routine upkeep is keeping the air cooled condenser clear of dust so it can reject heat, checking that the timer drain is actually discharging rather than quietly plugged, and leaving clearance around the cabinet for condenser airflow. The hot gas bypass valve is factory set and is not a field adjustment, so a dew point reading sitting outside the green zone usually points to a dirty condenser, a hot room, or incoming air above the 122 degree F limit rather than to the valve itself.
Sizing it to your compressor
Size the dryer to the compressor it follows, not to the pipe it bolts into. At 200 CFM the COOL 200 covers the entire ABAC rotary screw range with headroom to spare, including the 30 HP AS-30 at 114 CFM, and it will dry a duplex piston compressor or two machines running into a common header.
Published ratings assume reference conditions of 100 PSI operating pressure, 95 degrees F inlet air and 77 degrees F room temperature, and real conditions move the number in both directions. Heat is what costs you capacity: ABAC applies a 0.84 correction factor at a 95 degree F room and 0.82 at 104 degree F inlet air, and inlet temperature bites hardest of the three. Line pressure works the other way and gives a little back, with ABAC's correction rising from 1.00 at 100 PSI to 1.13 at 188 PSI, so a system running high recovers some of what a hot room takes away. Allow headroom rather than sizing to the nameplate, and fit an aftercooler ahead of the dryer when it sits close to the compressor discharge.
How it compares and what to pair it with
Capacity is the main step between COOL models. The smaller units through the COOL 125 are rated to 232 PSI and run R-134a refrigerant, while the COOL 150, this COOL 200 and the COOL 250 are rated to 188 PSI and run R-404A. If your system regularly sits above 188 PSI, size around that ceiling rather than around flow alone. The 150, the 200 and the 250 share the same 12 x 28 x 39 inch cabinet and all three run on 230V single phase power, so stepping up the range does not cost you floor space or a new three phase feed.
Put a coalescing filter upstream for oil carryover and a particulate filter downstream when the work calls for cleaner air, give it a dry, well ventilated spot with clearance for the condenser airflow, and keep it out of the heat thrown off by the compressor itself. See the rest of our refrigerated air dryers and our full air dryers lineup, or call us for installation clearances before you pipe it in.
NOTE: Actual product may be different from pictured!
Financing Options
Financing Options
We offer Financing Through Many Different Avenues:
- Affirm is great for smaller purchases. You can do this during checkout.
- Clicklease is a great option for Instant decisions up to 25k. NO Hard credit pull. No Time in Business Required. More information can be found out about it here: https://www.clicklease.com/partner/warthog-air-compressor-store
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
AirCompressorStore.com offers a complete selection of air compressors, parts and accessories designed to keep your equipment running reliably and efficiently. Whether you’re servicing a small shop compressor, maintaining an industrial air system, or replacing a worn component in a production environment, our parts are sourced from trusted manufacturers and built to meet the demands of real-world compressed air applications.