Champion PL-Series Pressure-Lubricated Bare Pumps | PL15A, PL30A, PL40A, PL70A
| Specifications (As Configured) | |
|---|---|
|
Champion
|
|
|
PL15A
|
|
| Dimensions | |
|
135.0 lb
|
|
A bare pump is the compressor itself and nothing else. No motor, no tank, no starter, no baseplate. Champion builds four of them in the PL-Series: the PL15A, PL30A, PL40A and PL70A. All four are two stage, all four are pressure lubricated, and all four are rated to 250 PSIG. That last figure is the reason the range exists. Champion's splash lubricated R-Series pumps stop at 175 PSIG, and Champion's own footnote in the price book says only pressure lubricated units are capable of 250 PSI. If the job needs 250, it needs a PL.
Three kinds of buyer end up on this page. The first has a package whose pump is worn out while the motor, receiver and controls are all fine, and replacing the pump costs a third of replacing the machine. The second is building compressed air into a larger assembly and wants the pump without Champion's packaging decisions attached. The third keeps a spare on a shelf because an unplanned day of downtime costs more than the pump does.
The four pumps
| Model | Motor HP it is built for | Cylinders | Bore and stroke (in) | Max pressure | Est. ship weight | Champion list | Our price |
|---|---|---|---|---|---|---|---|
| PL15A | 5 and 7.5 | 2 | 4-5/8 and 2-1/2 x 3 | 250 psi / 17.2 bar | 135 lb (61 kg) | $5,340 | $2,866 |
| PL30A | 7.5, 10 and 15 | 4 | 4-5/8 (2) and 2-1/2 (2) x 3 | 250 psi / 17.2 bar | 240 lb (109 kg) | $10,660 | $5,720 |
| PL40A | 15 | 2 | 6-1/4 and 3-1/4 x 4-1/2 | 250 psi / 17.2 bar | 250 lb (113 kg) | $15,090 | $8,098 |
| PL70A | 20, 25 and 30 | 4 | 6-1/4 (2) and 3-1/4 (2) x 4 | 250 psi / 17.2 bar | 590 lb (268 kg) | $21,640 | $11,612 |
In millimetres the bores and strokes are 117.5 and 63.5 x 76.2 on the PL15A, the same doubled on the PL30A, 158.8 and 82.6 x 114.3 on the PL40A, and the same doubled on the PL70A. The PL30A is a four cylinder version of the PL15A and the PL70A is a four cylinder version of the PL40A, which is why the bore and stroke figures repeat.
Horsepower does not size these pumps. Pump speed does.
This is the part that trips people up on a bare pump order. The same casting appears in packages of very different output, because Champion changes the pulley rather than the pump. Here is how Champion applies each of these four pumps across its own PL-Series packages, taken from the August 2026 price book.
| Pump | Motor HP | Pump RPM at 175 PSI | ACFM at 175 PSIG | ACFM at 250 PSIG |
|---|---|---|---|---|
| PL15A | 5 | 705 | 16.2 | 13.6 |
| PL15A | 7.5 | 990 | 22.1 | 21.3 |
| PL30A | 7.5 | 570 | 25.8 | 21.3 |
| PL30A | 10 | 718 | 33.8 | 27.5 |
| PL30A | 15 | 1035 | 46.3 | 41.0 |
| PL40A | 15 | 776 | 53.7 | 45.8 |
| PL70A | 20 | 664 | 77.5 | 63.2 |
| PL70A | 25 | 776 | 90.1 | 76.8 |
| PL70A | 30 | 907 | 101.0 | 90.0 |
Two things fall out of that table and both of them matter when you are choosing between two pumps rather than replacing one.
At 7.5 HP you can buy either a PL15A turning 990 RPM or a PL30A turning 570 RPM. The bigger pump running slower makes more air, 25.8 ACFM against 22.1, and it does it at roughly half the piston speed. It costs almost exactly twice as much. If the machine runs a shift a day, the PL15A is the sensible buy. If it runs continuously, the slower pump is the one that is still there in ten years.
The same choice repeats at 15 HP between the PL30A at 1035 RPM and the PL40A at 776 RPM, and again the slower pump makes more air, 53.7 against 46.3. Champion sells both because both are right, for different duty cycles.
Note also what 250 PSIG costs you in capacity. On the PL70A at 20 HP, going from 175 to 250 PSIG drops delivered air from 77.5 to 63.2 ACFM, which is a fifth of the output. Size the pump at the pressure you will actually run, not at the headline figure.
What is on the pump and what is not
Head unloaders are standard on all four. The NPT manifold is standard on the two four cylinder pumps, the PL30A and the PL70A, and is a priced option on the PL15A and the PL40A. Everything else on Champion's list for this page is an extra: low oil stop control, low oil pressure switch, food grade oil fill and a domestic wood crate.
What you are not getting, and should budget for separately: motor, pulleys, belts, belt guard, baseplate, receiver, starter, control panel, pressure switch, aftercooler, intake piping and the safety relief valve. A bare pump is not a compressor until someone makes those decisions.
Factory-installed options
The five priced adders for these pumps are listed and priced individually on the PL-Series bare pump options and adders page. They have to be ordered with the pump, because they are installed at the factory in Sedalia, not fitted in the field.
One thing worth flagging before you compare pages. The low oil stop control, food grade oil and domestic wood crate all appear on Warthog at a different price on our packaged PL-Series listings than they do here. That is not an error. Champion discounts a bare pump on a different schedule from a complete package, and a factory option follows the rate of the equipment it is bolted to. The list price Champion prints is the same on both; what we pay is not.
Pressure lubrication, and when it is worth the money
A splash lubricated pump throws oil around the crankcase with dippers on the connecting rods. It works, it is cheap, and it is what most small shop compressors use. A pressure lubricated pump runs an oil pump and feeds oil under pressure to the bearings and wrist pins, the same way a car engine does, and it has an oil pressure circuit you can monitor.
That buys you two things. Higher pressure capability, because the bearings can take the load at 250 PSIG. And the ability to shut the machine down on loss of oil pressure rather than on a float switch, which is what the low oil pressure switch option is for. If the pump is unattended, that option is cheap insurance against a seized crankshaft.
If the job is 175 PSIG and somebody is in the building, Champion's splash lubricated R-Series bare pumps do the same work for less money and we will say so.
Ordering notes
Champion's order entry configurator for this whole page is PL3-30-BARE-A, the same number for all four pumps and every option combination. It does not distinguish one pump from another, so we pin the model number on every order rather than relying on the configurator.
Compare-at pricing on this page is the full Champion August 2026 list, effective 15 August 2026. Our price is what we advertise, and it is set from Champion's published distributor schedule rather than marked down from list by a flat percentage.
Shipping weights above are Champion's estimated figures from the price book and are what the freight quote is built on. The PL70A at 590 lb is a forklift item, not a two person lift.
Where the price book is silent, and where it disagrees with itself
Page 50 of the August 2026 reciprocating book publishes bore, stroke, cylinder count, maximum pressure, weight and horsepower applicability, and nothing else. There are no dimensions for any of these four pumps, no sound level, no rated or maximum RPM range for the pump itself, no freight terms and no base warranty statement. We are not going to invent any of those. If you need a dimensional drawing or a warranty position in writing before you buy, ask us and we will get it from Champion rather than guess.
One inconsistency worth knowing about if you cross-check our figures against the book. On page 37 Champion prints the 7.5 HP base mount package at 18.2 ACFM at 250 PSIG while every tank mounted package on the same page, same PL15 pump at the same 990 RPM, is printed at 21.3. A base mount has no receiver, so it cannot have a different pump capacity. We have asked Champion which figure is right and we have used 21.3 in the table above. The 175 PSIG figure is 22.1 across all five.
Champion's own footnote on page 50 reads that the PL-15 engine drive pump comes with the NPT manifold as standard. The asterisk that footnote belongs to is not printed anywhere in the table, and the word manifold is misspelled in the book. We read it as applying to the PL15A NPT manifold row and have asked for confirmation.
Questions we get
Can I put a PL pump on my existing R-Series tank and motor? Mechanically it will usually bolt down, but it is rarely the right call. The pulley ratio, belt length and motor speed were all chosen for the old pump, and a 250 PSIG pump on a 175 PSIG receiver and relief valve is a code problem, not just a performance one. Send us what you have and we will tell you whether it is worth doing.
Is the PL30A just two PL15A pumps? It is the same bore and stroke doubled, four cylinders instead of two, on a bigger crankcase. It is not two pumps and it is not a duplex. A duplex is two complete compressors with two motors on one tank, which is a different product.
Do you stock these? They ship from Champion in Sedalia, Missouri rather than from our shelf. Lead time moves with the factory, so ask before you plan an outage around a date.
Buying from Warthog
We are an authorized Champion distributor and we sell the pump at the price on this page, not a teaser price that changes at checkout. Pricing here comes straight out of the August 2026 Champion price book. If you tell us the application, the duty cycle and the pressure you actually run, we will tell you which of these four pumps is right and whether a complete package would cost you less in the end than a pump plus the parts around it.
NOTE: Actual product may be different from pictured!
Financing Options
Financing Options
We offer Financing Through Many Different Avenues:
- Affirm is great for smaller purchases. You can do this during checkout.
- Clicklease is a great option for Instant decisions up to 25k. NO Hard credit pull. No Time in Business Required. More information can be found out about it here: https://www.clicklease.com/partner/warthog-air-compressor-store
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
AirCompressorStore.com offers a complete selection of air compressors, parts and accessories designed to keep your equipment running reliably and efficiently. Whether you’re servicing a small shop compressor, maintaining an industrial air system, or replacing a worn component in a production environment, our parts are sourced from trusted manufacturers and built to meet the demands of real-world compressed air applications.
