ABAC QDT 115 Electronic Automatic Tank Drain for Air Receivers
| Specifications (As Configured) | |
|---|---|
|
ABAC
|
|
|
8102048377
|
|
The ABAC QDT 115 is an electronic automatic tank drain for compressed air receivers. It replaces the manual petcock at the bottom of the tank and clears condensate on a timer, so the water that collects in the receiver goes out on its own instead of waiting for somebody to remember to crack the valve.
Key details
- Model: QDT 115
- Part number: 8102048377
- Type: electronic timer operated automatic tank drain
- Fits: the ABAC vertical air receiver range
- Brand: ABAC, part of the Atlas Copco group
Why an automatic drain is worth fitting
Every compressor makes water. Air going into a receiver is warm and wet, it cools in the tank, and the moisture drops out and sits in the bottom. Left there it rusts the vessel from the inside, shortens the life of the tank, and carries downstream into air lines, tools and finishing work the moment the level gets high enough. A manual drain only works if it gets opened, and in most shops it does not get opened often enough.
An electronic timer drain takes the job off the operator. It opens on a set interval, discharges the collected condensate, and closes again. Fit one and the receiver drains whether anyone thinks about it or not, including over a weekend or a shutdown when the tank is sitting full of water and nobody is near it.
How much water ends up in the tank
More than most people expect. A compressor is a dehumidifier nobody asked for: it draws in ambient air, squeezes it into a fraction of its original volume, and the moisture that air was carrying has nowhere to go but out of suspension as the compressed air cools inside the receiver. The warmer and more humid the room, and the more hours the machine runs, the more liquid water collects in the bottom of the tank.
That is the part worth sitting with. Water in a receiver is not a housekeeping problem, it is a pressure vessel problem. It attacks the tank from the inside at the one point an inspection is least likely to reach, and the first sign of trouble is usually rust coming out of the drain, or a tank that fails a hydrostatic test years earlier than it should have. Getting the condensate out on a schedule is the cheapest life extension available for a receiver.
Timer drains and the alternatives
A timer drain works on an interval: it opens for a short period, blows the collected water out under tank pressure, and shuts again. It is simple, there is very little to go wrong, and it costs a fraction of what a smarter drain costs. The trade is that it vents some compressed air along with the water every time it fires, and the interval has to be set to suit the duty. Too long and water backs up between cycles, too short and the compressor pays for air it never used.
Zero loss and demand style drains sense the condensate level instead and open only when there is water to clear, so they waste no air. They cost more and have more to go wrong. For a receiver on a shop compressor a timer drain is usually the right call, and the air it vents is a rounding error next to a rusting tank. Larger systems and plants running expensive air are where the zero loss drains start to pay for themselves. See the full range of condensate drains to compare.
Installation notes
The drain goes into the bottom port of the receiver, which is usually the lowest point of the vessel so condensate collects there. Give the discharge somewhere to go. Condensate off a compressor carries oil, so in most places it cannot go to a floor drain untreated, and an oil water separator or a collection container is the normal answer.
If the drain is replacing a plugged or seized manual petcock, check the port thread before ordering fittings, and fit an isolation valve ahead of the drain so it can be serviced without depressurizing the whole receiver. Keep the run between tank and drain short and avoid a trap where sludge can settle. Point the discharge into a container rather than at the floor, because what comes out is under tank pressure and it arrives fast.
Keeping it working
Rust scale, pipe dope and sludge are what kill automatic drains. Most electronic drains are fitted with or behind a strainer for exactly that reason, and the strainer is the service item: clean it on a schedule and the drain keeps clearing, ignore it and the drain eventually fires into a blocked port while the tank quietly fills back up. Check once in a while that the drain is actually discharging, especially in the first few weeks on an older tank with years of scale in the bottom.
In an unheated shop, protect the drain and its discharge line from freezing. A line full of ice is the same as a blocked line, and the first warm day usually reveals a receiver that has been holding water for a month.
What to pair it with
A tank drain deals with the water that has already fallen out inside the receiver. It does nothing about the moisture still suspended in the air heading down the pipe, which is what spoils paintwork, freezes outdoor lines and corrodes tools from the inside. If the air goes to spraying, blasting, tires or instrumentation, a refrigerated dryer downstream is the other half of the job: see the ABAC COOL 15 for a small shop, or the rest of our refrigerated air dryers for larger systems.
For treating what the drain discharges, look at our oil water separators. See our air compressor tanks if you are building a receiver up from scratch, and our tank drain kits for complete drain assemblies. Call us if you want the published electrical supply and timer settings for this drain confirmed against your receiver before you order.
NOTE: Actual product may be different from pictured!
Financing Options
Financing Options
We offer Financing Through Many Different Avenues:
- Affirm is great for smaller purchases. You can do this during checkout.
- Clicklease is a great option for Instant decisions up to 25k. NO Hard credit pull. No Time in Business Required. More information can be found out about it here: https://www.clicklease.com/partner/warthog-air-compressor-store
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
AirCompressorStore.com offers a complete selection of air compressors, parts and accessories designed to keep your equipment running reliably and efficiently. Whether you’re servicing a small shop compressor, maintaining an industrial air system, or replacing a worn component in a production environment, our parts are sourced from trusted manufacturers and built to meet the demands of real-world compressed air applications.