Atlas Copco FX Refrigerated Air Dryer Series
| Specifications (As Configured) | |
|---|---|
|
Atlas Copco
|
|
|
8102229350
|
|
OLD SKU |
|
|
|
|
|
|
|
| Dimensions | |
|
42.0 lb
|
|
Shipping Height |
|
Shipping Length |
|
Shipping Width |
|
| Downloadable Files | |
Brochure PDFClick to Download
|
|
Atlas Copco FX non cycling refrigerated air dryers, 9 to 572 CFM
The FX is Atlas Copco's non cycling refrigerated dryer: the refrigeration circuit runs continuously and a hot gas bypass valve holds the evaporator just above freezing, so the dew point stays steady at roughly 38°F whether the compressor is at full load or idling. It is the right dryer for a shop that needs tools, paint lines and piping protected from water and does not need the energy savings of a cycling dryer. If your air demand swings a lot through the day and the power bill matters, look at the FD cycling dryer instead; same quality of air, lower running cost at part load.
Sizing is where refrigerated dryers get bought wrong, and the nameplate is the trap. Atlas Copco rates the FX at 77°F in the room, 95°F going in and 7 bar, roughly 100 PSIG. Those are reference conditions, not plant conditions, and the correction factors are steeper than most people expect. At 90°F ambient with 100°F inlet air an FX holds about 78 percent of its rating. At 100°F ambient with 110°F inlet it's down near 55 percent. Line pressure pushes back the other way, so a compressor running 125 PSIG hands you about 12 percent of it back.
Work it in that order. Start with the compressor's delivered CFM at its actual discharge pressure, correct for the room and inlet temperatures you will see in the worst week of the year rather than today, then take the first model that still clears the number. A packaging plant outside Atlanta we quoted this month puts 97 CFM off a 25 HP screw into a 90°F room, with a good aftercooler holding inlet air within ten degrees of ambient. On paper that's an FX48N at 102 CFM. Corrected, the FX48N delivers about 89 CFM and the job takes the FX61N.
Horsepower rules of thumb fail for the same reason, so size on measured CFM and real conditions. Send us the compressor model, the discharge pressure and how hot the room gets in August and we will run the corrections with you.
This listing runs from the FX4N at 9 CFM to the FX270N at 572 CFM. Models through the FX69N (147 CFM) are 115 volt single phase and plug in; the FX86N and FX108N are 230 volt single phase; the FX150N and up are 460 volt three phase. Maximum working pressure is 188 PSIG, so these suit every piston and screw compressor we sell up to 175 PSI.
Install it after the receiver tank, not between the compressor and the tank, so the air arrives cooler and the dryer is not hit by every pump cycle. Put a UD+ coalescing filter ahead of it to catch oil and liquid water, and plumb the automatic drain to a floor drain or an oil water separator. For instrument air, outdoor lines or paint booths that need a minus 40 dew point, a refrigerated dryer is not enough; see the CD heatless desiccant dryer. Browse all refrigerated air dryers and air dryers.
Manufacturer description
Atlas Copco FX Refrigerated Air Dryer Series
Get clean, dry compressed air with a stable pressure dew point as low as 3 to 5 °C, engineered for dependable performance and low lifecycle cost. The FX Series uses a compact 3-in-1 heat exchanger (air/air + air/refrigerant) to maximize thermal transfer while minimizing pressure drop (approx. 0.28 bar across the range). A hot-gas bypass valve maintains evaporator pressure to prevent freeze-up at partial loads. The air-cooled condenser’s large surface area, capillary tube expansion, and protected refrigerant compressor (high-pressure & start-up protection) round out a robust, plug-and-play package. A digital controller with a large LCD shows PDP/LAT and operating status, while the dual timer & float drain ensures reliable condensate removal.
Range & core specs (reference conditions)
- Models: FX 6-FX 400 (air treatment capacity 6 to 400 l/s).
- Nominal electrical power @50 Hz: approx. 220 to 3500 W (by model).
- Max working pressure: 13 bar.
- Refrigerants: R134a (FX 6 to 35), R410A (FX 45 to 400), zero ODP refrigerants.
- Connections: from G 3/4″ up to G 2.5″ (by model).
- Form factor/weight: compact footprints; typical envelopes from ~517×500×805 mm to ~1045×950×1035 mm; approx. 50 to 190 kg (by model).
- Typical pressure drop: 0.28 bar.
Operating limits & conditions
- Reference conditions: 25 °C ambient, 35 °C inlet, 7 bar(g).
- Ambient: 5 to 46 °C; Max inlet temp: 62 °C.
- ISO air quality: Achieves ISO 8573-1 Class 4 at 3 °C/38 °F PDP (≤15 μm particles; PDP 3 °C; oil ≤5 mg/m³).
Capacity correction factors (apply multipliers)
- Dew point: 0.7 @ 3 °C, 1.0 @ 5 °C.
- Ambient temp (°C): 1.00 (25), 0.91 (30), 0.81 (35), 0.72 (40), 0.61 (45), 0.60 (46).
- Inlet temp (°C): 1.00 (≤35), 0.82 (40), 0.67 (45), 0.55 (50), 0.44 (55), 0.36 (60), 0.34 (62).
- Inlet pressure (bar): 0.75 (5), 0.88 (6), 1.00 (7), 1.08 (8), 1.15 (9), 1.22 (10), 1.28 (11), 1.34 (12), 1.39 (13).
Why FX for your plant
- Performance & reliability: stable 3 to 5 °C PDP; efficient 3-in-1 exchanger; full-range hot-gas bypass; dual drain; advanced controller that also trims power at low load.
- User-friendly: compact footprint, quick plug-and-play setup; big LCD with PDP/LAT; easy access for service.
- Energy savings: low pressure drop; efficient compressor; variable fan speed control.
- Environment-friendly: R134a/R410A with zero ozone-depletion potential; low power draw reduces indirect emissions.
Typical applications:
Pneumatic tools & controls, painting, packaging, injection molding, auto service/tire inflation, and a wide range of industrial/professional uses requiring reliable Class 4 dry air.
In short: FX delivers reliable Class 4 air, tight PDP control, and low pressure drop in a durable, service-friendly package sized from FX 6 to FX 400 for everything from small shops to heavy industry.
NOTE: Actual product may be different from pictured!
Financing Options
Financing Options
We offer Financing Through Many Different Avenues:
- Affirm is great for smaller purchases. You can do this during checkout.
- Clicklease is a great option for Instant decisions up to 25k. NO Hard credit pull. No Time in Business Required. More information can be found out about it here: https://www.clicklease.com/partner/warthog-air-compressor-store
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
AirCompressorStore.com offers a complete selection of air compressors, parts and accessories designed to keep your equipment running reliably and efficiently. Whether you’re servicing a small shop compressor, maintaining an industrial air system, or replacing a worn component in a production environment, our parts are sourced from trusted manufacturers and built to meet the demands of real-world compressed air applications.
Brochure PDF
