{"title":"ABAC Horizontal Tank Air Compressors","description":"\u003cp\u003eA horizontal tank lays the receiver on its side, so the machine sits low and wide instead of tall. Where a vertical unit needs headroom and a bolted-down corner, a horizontal one slides under a mezzanine, rides in a service truck bed, or lives in a bay with a low ceiling. Airflow and pressure do not change with orientation, so this is a siting decision rather than a performance one.\u003c\/p\u003e\u003ch3\u003eWhat is in this range\u003c\/h3\u003e\u003cp\u003eABAC builds horizontal machines from 30 to 200 gallons and 7.5 to 20 HP, all rated at 175 PSI:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e30 gallon gas drive:\u003c\/strong\u003e the AB13-30GH on the hybrid T39 pump, and the Ironman ABC11-30GH, ABC13-30GH, ABC14-30GK and ABC16-30GV on fully cast iron pumps, 22 to 32 CFM behind Honda, Kohler and Vanguard engines. No shore power needed, which is why they go on service trucks and remote job sites.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e80 gallon two-stage:\u003c\/strong\u003e the AB7-2180HS and the premium AB7-2180HFF, 7.5 HP on the hybrid T39 pump, 22.2 CFM.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e120 gallon Ironman:\u003c\/strong\u003e the largest group here. Simplex ABC10 machines at 32 CFM on a C2 cast iron pump, plus duplex ABC5, ABC7 and ABC10 pairs from 32 to 64 CFM.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e200 gallon duplex:\u003c\/strong\u003e the 20 HP ABC10-23200HD and ABC10-2320DHP, 64 CFM on C2 cast iron pumps, with alternating control so the two pumps share the hours.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy buyers choose duplex\u003c\/h3\u003e\u003cp\u003eMore than half of this range is duplex: two pumps and two motors on one receiver, alternating so each runs about half the time. A duplex machine covers a peak that a single pump cannot, keeps producing air when one side is down for service, and starts in smaller electrical steps than one large motor. If the shop runs air all day and cannot afford a stoppage, that redundancy is usually worth more than the extra CFM. See the full set in \u003ca href=\"\/collections\/abac-duplex-air-compressors\"\u003eABAC duplex air compressors\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eSizing and setup\u003c\/h3\u003e\u003cp\u003eSize on the CFM your tools draw at once, plus roughly 30 percent of headroom, then check the panel: the electric machines here are set to 230V, 460V or 575V three-phase at build, and the gas drive units need no panel at all. If the air feeds paint, plasma or tires, pair the compressor with a dryer from the \u003ca href=\"\/collections\/abac-cool-refrigerated-air-dryers\"\u003eABAC COOL range\u003c\/a\u003e. For the same sizes standing on end, see \u003ca href=\"\/collections\/abac-vertical-tank-air-compressors\"\u003eABAC vertical tank air compressors\u003c\/a\u003e, or browse the full brand in \u003ca href=\"\/collections\/abac-air-compressors\"\u003eABAC air compressors\u003c\/a\u003e. ABAC is part of the Atlas Copco group.\u003c\/p\u003e","products":[{"product_id":"abac-ab7-7-5-hp-80-gallon-horizontal-two-stage-air-compressor","title":"ABAC AB7-2180HS 7.5 HP Two-Stage Air Compressor - 80 Gallon Horizontal, 175 PSI, 22.2 CFM T39 Pump","description":"\u003cp\u003eThe ABAC AB7 horizontal series delivers the same 7.5 HP, 22.2 CFM two-stage performance as the AB7 vertical models, on a low-profile 80 gallon horizontal ASME tank that fits under benches, shelving, and low ceilings where a 75-inch vertical unit will not. The belt-driven T39 two-stage pump combines an aluminum block with cast iron cylinders and inner cooling technology for cool, continuous operation at a maximum 175 PSI. Choose 230V single-phase (AB7-2180HS), 230V three-phase (AB7-2380HS), or 460V three-phase (AB7-4380HS).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AB7-2180HS (230V\/1, part 8090304372), AB7-2380HS (230V\/3, part 8090304422), AB7-4380HS (460V\/3, part 8090303689)\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP\u003c\/li\u003e\n\u003cli\u003ePump: T39 two-stage hybrid, aluminum block with cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 22.2 CFM at max pressure (ABAC publishes 22.23 CFM for all three voltage and phase versions)\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 80 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eAluminum heads and aftercooler, inner cooling technology\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eStart\/stop pressure switch control\u003c\/li\u003e\n\u003cli\u003eWeight: 413 lbs | Dimensions: 25\" x 71\" x 48\"\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat the Hybrid Pro build buys you\u003c\/h3\u003e\u003cp\u003eABAC calls this range Hybrid because the pump is not all one metal. The cylinders are cast iron, which is the part that takes the heat and the wear on a two-stage machine, while the head and the aftercooler are aluminum, which sheds that heat faster than cast iron can. ABAC pairs the two with what it calls inner cooling technology, routing interstage air through the cooler before the second stage sees it. The practical result is lower discharge temperature, less moisture carried into the tank, and a pump that runs smoother and quieter than an all cast iron equivalent at the same horsepower. The fully enclosed belt guard is doing double duty as well: it is a guard, and it channels cooling air across the pump.\u003c\/p\u003e\u003cp\u003eBecause the three voltage versions share one pump and one motor rating, there is no airflow penalty for picking the phase that matches your panel. All three are rated at 22.23 CFM at 175 PSI.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 2-Stage Hybrid Pro range the pump and motor are identical across tank formats, so the choice comes down to footprint and features. The \u003ca href=\"\/products\/abac-ab7-7-5-hp-80-gallon-vertical-two-stage-air-compressor\"\u003eAB7-2180V vertical\u003c\/a\u003e puts the same 22.2 CFM on a 25 x 34 x 75 in footprint at 403 lbs, which saves floor space but needs ceiling height. The \u003ca href=\"\/products\/abac-ab7-hff-7-5-hp-80-gallon-horizontal-premium-air-compressor\"\u003eAB7-2180HFF Full Feature horizontal\u003c\/a\u003e adds a pressure-actuated automatic tank drain and a low oil level switch on the same chassis. If you want a full cast iron pump rather than the aluminum and cast iron hybrid, the \u003ca href=\"\/products\/abac-abc7-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eIronman ABC7-2180V\u003c\/a\u003e delivers 21 CFM from a C1 cast iron pump. Stepping down, the \u003ca href=\"\/products\/abac-ab5-2180vp-5-hp-80-gallon-vertical-two-stage-air-compressor\"\u003e5 HP AB5-2180VP\u003c\/a\u003e gives 16.6 CFM on the same 80 gallon receiver, which is the right call for a one or two technician shop that does not run sanders continuously.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eShops with height restrictions or mezzanines, mobile service buildings, and installations where the compressor tucks under a workbench or against a knee wall. ABAC rates the Hybrid Pro range for tire inflation, hammering, air and water spraying, grinding, fastening, and general equipment operation, and lists the series for automotive, agriculture and farm, food and beverage, and light industrial work. In practice a single AB7 supports several technicians on impacts, sanders, and spray guns without the recovery lag of a smaller single-stage machine. The 80 gallon receiver keeps the pump from short cycling between tool triggers.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eSpecify the voltage and phase that matches your panel before ordering: the 230V single-phase version draws the highest current of the three and usually wants a dedicated circuit, while the 230V and 460V three-phase versions suit shops already running three-phase service. In the horizontal format the discharge and tank drain sit low, so leave service clearance on the drain side, and leave room at the belt guard end for cooling air and for belt and pump service. Drain the receiver on a schedule or the moisture that a 175 PSI machine condenses will sit in the bottom of the tank; the \u003ca href=\"\/products\/abac-ab7-hff-7-5-hp-80-gallon-horizontal-premium-air-compressor\"\u003eFull Feature version\u003c\/a\u003e automates that if nobody on the floor will remember. Moisture carries over on any 175 PSI reciprocating compressor running hard, so pair the AB7 with an \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL refrigerated air dryer\u003c\/a\u003e sized against your actual duty cycle if you are spraying finishes or feeding pneumatic controls.\u003c\/p\u003e\u003cp\u003ePart of ABAC's 2-Stage Hybrid Pro range from the Atlas Copco group. See the rest of our \u003ca href=\"\/collections\/air-compressors\"\u003eair compressors\u003c\/a\u003e and the matching \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V Single-Phase","offer_id":54557406134547,"sku":"8090304372","price":3612.0,"currency_code":"USD","in_stock":true},{"title":"230V Three-Phase","offer_id":54557406167315,"sku":"8090304422","price":3612.0,"currency_code":"USD","in_stock":true},{"title":"460V Three-Phase","offer_id":54557406200083,"sku":"8090303689","price":3612.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-ab7-2180hs-80-gallon-horizontal.jpg?v=1791392752"},{"product_id":"abac-ab7-hff-7-5-hp-80-gallon-horizontal-premium-air-compressor","title":"ABAC AB7-2180HFF 7.5 HP Two-Stage Air Compressor - 80 Gallon Horizontal Premium, 175 PSI, 22.2 CFM T39 Pump","description":"\u003cp\u003eThe ABAC AB7-2180HFF is the Full Feature build of the 80 gallon horizontal AB7 platform. The belt-driven T39 two-stage pump pairs an aluminum head and aftercooler with cast iron cylinders, so heat comes out of the air before it reaches the receiver, and the FF specification adds a pressure-actuated automatic tank drain and a low oil level switch. It delivers 22.2 CFM at a maximum 175 PSI on a low-profile tank that fits under benches, mezzanines and low ceilings where a 75 inch vertical machine will not. The same build is offered on 230V single-phase, 230V three-phase and 460V three-phase power.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AB7-2180HFF (230V\/1, part 8090304380), AB7-2380HFF (230V\/3, part 8090304430), 460V\/3 horizontal Full Feature (part 8090304471)\u003c\/li\u003e\n\u003cli\u003eFull Feature additions: pressure-actuated automatic tank drain, low oil level switch\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP\u003c\/li\u003e\n\u003cli\u003ePump: T39 two-stage hybrid, aluminum head and aftercooler with cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 22.2 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 80 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eStart\/stop pressure switch control\u003c\/li\u003e\n\u003cli\u003eWeight: 413 lbs | Dimensions: 25\" x 71\" x 48\"\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eEvery 80 gallon AB7 runs the same T39 pump and the same 22.2 CFM at 175 PSI, so the choice is footprint and fitted equipment rather than output. The \u003ca href=\"\/products\/abac-ab7-7-5-hp-80-gallon-horizontal-two-stage-air-compressor\"\u003eAB7-2180HS\u003c\/a\u003e is this same horizontal machine without the automatic drain and the oil level switch. The \u003ca href=\"\/products\/abac-ab7-ff-7-5-hp-80-gallon-vertical-premium-air-compressor\"\u003eAB7-2180VFF\u003c\/a\u003e is the Full Feature specification on a vertical tank, 25 x 34 x 75 in, for shops with ceiling height but tight floor space, and the \u003ca href=\"\/products\/abac-ab7-7-5-hp-80-gallon-vertical-two-stage-air-compressor\"\u003eAB7-2180V\u003c\/a\u003e is the standard vertical. Where 22.2 CFM is more than the shop draws, the \u003ca href=\"\/products\/abac-ab5-2180vpff-5-hp-80-gallon-vertical-premium-air-compressor\"\u003e5 HP AB5-2180VPFF\u003c\/a\u003e runs 16.6 CFM in the same Full Feature trim. If a fully cast iron pump suits the duty better than the aluminum and cast iron hybrid, the \u003ca href=\"\/products\/abac-abc7-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eIronman ABC7-2180V\u003c\/a\u003e delivers 21 CFM from a C1 pump.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eMulti-bay auto repair and body shops, tire stores, welding and fabrication bays, woodworking shops and farm buildings with a height restriction: impact wrenching, grinding, orbital sanding, fastening, and air or water spraying where tools run through most of the shift. A two-stage pump recovers faster than a single-stage machine of the same horsepower, so several technicians can stay on tools without waiting on pressure, and the 80 gallon receiver keeps the pump from short cycling between tool triggers. The automatic drain and the oil level switch cover the two daily checks most often skipped where nobody is assigned to the compressor.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eSpecify the voltage and phase that matches your panel before ordering. The 230V single-phase version draws the highest current of the three and normally wants a dedicated circuit sized to the motor nameplate, while the 230V and 460V three-phase versions suit shops already running three-phase service. Allow for the 25 by 71 inch floor footprint and 48 inches of height, leave service clearance on the drain side where the discharge and tank drain sit low on a horizontal tank, and keep the intake away from paint fumes and sanding dust. Belts, filters and oil are the routine service items on this range.\u003c\/p\u003e\u003cp\u003eA two-stage pump still pushes warm, wet air into the line, so size a refrigerated dryer above the 22.2 CFM output, such as the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35\u003c\/a\u003e, before the air reaches paint, tires or pneumatic controls. Part of ABAC's 2-Stage Hybrid Pro range from the Atlas Copco group. Browse the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/air-dryers\"\u003ecompressed air dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V Single-Phase","offer_id":54557408362771,"sku":"8090304380","price":3846.0,"currency_code":"USD","in_stock":true},{"title":"230V Three-Phase","offer_id":54557408395539,"sku":"8090304430","price":3846.0,"currency_code":"USD","in_stock":true},{"title":"460V Three-Phase","offer_id":54557408428307,"sku":"8090304471","price":3846.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-ab7-2180hff-80-gallon-horizontal-premium.jpg?v=1791396350"},{"product_id":"abac-ab5-duplex-10-hp-120-gallon-horizontal-air-compressor","title":"ABAC AB5-21120D 10 HP Two-Stage Duplex Air Compressor - 120 Gallon Horizontal, 175 PSI, 33.2 CFM","description":"\u003cp\u003eThe ABAC AB5-21120D mounts two independent 5 HP motor and pump assemblies on a single 120 gallon horizontal ASME tank. The controller alternates between pumps to even out wear, or runs both together when demand spikes, delivering a combined 33.2 CFM (16.6 CFM per pump) at a maximum 175 PSI. If one pump ever needs service, the other keeps the shop running: redundancy that a single-pump compressor simply cannot offer.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AB5-21120D 230V single-phase (part 8090304224), AB5-23120D 230V three-phase (part 8090304232), AB5-43120D 460V three-phase (part 8090304240)\u003c\/li\u003e\n\u003cli\u003ePower: 10 HP total, two 5 HP motors\u003c\/li\u003e\n\u003cli\u003ePumps: two T39 two-stage hybrid pumps, aluminum with cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 33.2 CFM combined, 16.6 CFM per pump at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eAlternating or simultaneous pump operation for uptime and peak capacity\u003c\/li\u003e\n\u003cli\u003eFully programmable control panel settings\u003c\/li\u003e\n\u003cli\u003eAluminum heads and aftercoolers, fully enclosed belt guards\u003c\/li\u003e\n\u003cli\u003eDual start\/stop pressure switch controls, magnetic starters\u003c\/li\u003e\n\u003cli\u003eWeight: 892 lbs | Dimensions: 25 x 79 x 55 in\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the Hybrid Pro duplex range the only variable is capacity, because the footprint does not change. The \u003ca href=\"\/products\/abac-ab7-duplex-15-hp-120-gallon-horizontal-air-compressor\"\u003eAB7-21120D\u003c\/a\u003e pairs two 7.5 HP pumps for 44.6 CFM on the same 120 gallon horizontal tank and the same 25 x 79 x 55 in floor space, at 910 lbs against this machine's 892. Against a single machine, the \u003ca href=\"\/products\/abac-ab5-2180vp-5-hp-80-gallon-vertical-two-stage-air-compressor\"\u003eAB5-2180VP\u003c\/a\u003e runs one 5 HP T39 pump at 16.6 CFM on an 80 gallon vertical tank, so the duplex doubles that output and adds the fallback a single-pump compressor cannot give you. If the duty cycle calls for full cast iron rather than the hybrid T39, the \u003ca href=\"\/products\/abac-abc5-duplex-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC5-21120HD Ironman duplex\u003c\/a\u003e is also 10 HP on 120 gallons, at 32 CFM with C1 cast iron pumps.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC positions the Hybrid Pro Duplex for work with a high variation in air demand, anywhere from intermittent duty up to 100 percent duty: hammering, spraying, grinding, fastening, orbital sanding and general equipment operation. Those are surge loads rather than steady ones, which is exactly where a duplex earns its price. One pump carries the baseline and the second joins only when the line calls for it, so neither motor spends the day short cycling the way a single large compressor would. Production shops, multi-bay service centers and any floor where an air outage stops the whole operation are the usual homes for this machine. Where the panel offers three-phase, the 230V or 460V three-phase build is the better long term choice, because a three-phase motor draws less current per leg and runs cooler under a hard duty cycle.\u003c\/p\u003e\u003cp\u003eTwo-stage compression sends warm, wet air down the line, so size a refrigerated dryer above the compressor's output rather than to the pipe. The \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35\u003c\/a\u003e is the smallest dryer in the COOL range that covers 33.2 CFM, and the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eCOOL 50\u003c\/a\u003e leaves room to spare in a warm shop. Part of ABAC's 2-Stage Hybrid Pro Duplex range from the Atlas Copco group. Browse the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V Single-Phase","offer_id":54557510730003,"sku":"8090304224","price":7041.0,"currency_code":"USD","in_stock":true},{"title":"230V Three-Phase","offer_id":54557510762771,"sku":"8090304232","price":6838.0,"currency_code":"USD","in_stock":true},{"title":"460V Three-Phase","offer_id":54557510795539,"sku":"8090304240","price":7136.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-ab5-duplex-120-gallon-horizontal-air-compressor.png?v=1786378023"},{"product_id":"abac-ab7-duplex-15-hp-120-gallon-horizontal-air-compressor","title":"ABAC AB7-21120D 15 HP Two-Stage Duplex Air Compressor - 120 Gallon Horizontal, 175 PSI, 44.6 CFM","description":"\u003cp\u003eThe ABAC AB7 Duplex is the largest piston duplex in ABAC's Hybrid Pro range: two independent 7.5 HP motor and pump assemblies on one 120 gallon horizontal ASME tank, producing a combined 44.6 CFM at a maximum 175 PSI. Alternating operation spreads runtime evenly across both pumps, while simultaneous operation covers peak demand that would overwhelm a single-pump machine. The second reason shops choose a duplex is redundancy: if one pump comes out for service, the other keeps the line pressurized instead of shutting the floor down. Choose 230V single-phase (AB7-21120D), 230V three-phase (AB7-23120D), or 460V three-phase (AB7-43120D).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AB7-21120D 230V single-phase (part 8090304257), AB7-23120D 230V three-phase (part 8090304265), AB7-43120D 460V three-phase (part 8090304273)\u003c\/li\u003e\n\u003cli\u003ePower: 15 HP total, two 7.5 HP motors, 60 Hz\u003c\/li\u003e\n\u003cli\u003ePumps: two T39 two-stage pumps, hybrid aluminum and cast iron construction\u003c\/li\u003e\n\u003cli\u003eAir delivery: 22.23 CFM per pump, 44.6 CFM combined with both sides running\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eAlternating or simultaneous pump operation for uptime and peak capacity\u003c\/li\u003e\n\u003cli\u003eFully programmable control panel with adjustable control parameters\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guards\u003c\/li\u003e\n\u003cli\u003eWeight: 910 lbs | Dimensions: 25 x 79 x 55 in\u003c\/li\u003e\n\u003cli\u003eAssembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a duplex instead of one bigger compressor\u003c\/h3\u003e\u003cp\u003eA duplex buys two things a single machine cannot. The first is uptime. A failed pump, a belt change or an oil service takes half the capacity offline instead of all of it, so the floor keeps working while the other side carries the load. The second is staging. Under light or intermittent demand the control alternates the two sides and shares the hours between them rather than loading one pump all day; when demand climbs, both sides run together for the full 44.6 CFM. Each pump then runs cooler, rests longer and reaches its service intervals later than one large pump doing the same total work. That is also why the published rating is 22.23 CFM per side: the machine is designed to spend most of its life running on one pump and to call on the second only when the line asks for it.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the Hybrid Pro duplex range the choice is capacity on an identical footprint. The \u003ca href=\"\/products\/abac-ab5-duplex-10-hp-120-gallon-horizontal-air-compressor\"\u003eAB5-21120D\u003c\/a\u003e pairs two 5 HP pumps for 33.2 CFM on the same 120 gallon horizontal tank and the same 25 x 79 x 55 in floor space, so the AB7 buys roughly eleven more CFM without asking for another square foot of shop, at 910 lbs against 892. Against a single machine, the \u003ca href=\"\/products\/abac-ab7-7-5-hp-80-gallon-vertical-two-stage-air-compressor\"\u003eAB7-2180V\u003c\/a\u003e runs one 7.5 HP T39 pump at 22.2 CFM; the duplex doubles that and adds the fallback a single-pump compressor cannot give you. If the duty cycle is hard enough to want full cast iron rather than the hybrid T39, the \u003ca href=\"\/products\/abac-abc7-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC7-21120HD Ironman duplex\u003c\/a\u003e is also 15 HP on 120 gallons, at 42 CFM with C1 cast iron pumps, and the \u003ca href=\"\/products\/abac-abc7-v2-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC7-2112DH2P\u003c\/a\u003e reaches 52 CFM at the same 15 HP with C2 pumps. Decide on duty cycle first and CFM second: the hybrid pump is the right answer for a shop that works in bursts, the cast iron pump for one that runs air most of the day.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eHigh-demand fabrication shops, collision centers running more than one booth, tire and fleet service bays, and industrial plants where sandblasting, plasma cutting, or several pneumatic stations draw at the same time. Those loads are the case for a duplex: demand arrives in surges rather than steadily, so one pump carries the baseline and the second joins only when the line calls for it, which keeps both motors off the short-cycling that shortens a single large compressor's life. ABAC builds the Hybrid Pro range for professional settings, metal and wood workshops and auto body and repair shops among them.\u003c\/p\u003e\u003ch3\u003ePower, installation and air quality\u003c\/h3\u003e\u003cp\u003eTake three-phase power if the panel has it. A three-phase motor draws less current per leg, starts easier and runs cooler on a compressor that cycles all day, and the 460V build keeps the wire size down on a long run from the panel. Each side draws its own load, so size the circuit for both pumps running together even though the control normally alternates them. At 79 inches long the horizontal tank runs along a wall and keeps the overhead clear, but leave room at the belt guards and flywheels for cooling air and service access, and plan the drain, because a 120 gallon receiver collects real water.\u003c\/p\u003e\u003cp\u003eTwo-stage compression still sends warm, wet air down the line, so size a refrigerated dryer above the compressor's output rather than to the pipe. At 50 CFM the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eABAC COOL 50\u003c\/a\u003e is the smallest dryer in the COOL range that covers 44.6 CFM with headroom, and it is worth having ahead of a paint booth, a plasma table or any tool line you would rather not run water through. Part of ABAC's 2-Stage Hybrid Pro Duplex range from the Atlas Copco group. Browse the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V Single-Phase","offer_id":54557511516435,"sku":"8090304257","price":7416.0,"currency_code":"USD","in_stock":true},{"title":"230V Three-Phase","offer_id":54557511549203,"sku":"8090304265","price":7416.0,"currency_code":"USD","in_stock":true},{"title":"460V Three-Phase","offer_id":54557511581971,"sku":"8090304273","price":7416.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-ab7-duplex-120-gallon-horizontal-air-compressor.png?v=1786378024"},{"product_id":"abac-ab13-30gh-13-hp-honda-gas-drive-air-compressor","title":"ABAC AB13-30GH 13 HP Honda Gas Drive Air Compressor - 30 Gallon Horizontal, 175 PSI, 22 CFM","description":"\u003cp\u003eThe ABAC AB13-30GH puts full shop-grade air anywhere a truck can reach. A 13 HP Honda gas engine drives a T39 hybrid pump on a 30 gallon horizontal ASME tank, producing 22 CFM at a maximum 175 PSI with no electrical service required. At 378 lbs it is the lightest machine in ABAC's gas engine range, which is what makes it the one crews actually lift onto a service bed.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AB13-30GH (part number 8090304620)\u003c\/li\u003e\n\u003cli\u003eEngine: 13 HP Honda gas, 12V electric start with recoil backup\u003c\/li\u003e\n\u003cli\u003ePump: T39 two-stage Hybrid Pro, aluminum block with cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 22 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 30 gallon horizontal, ASME tank and safety valves, EZ pull tank drain\u003c\/li\u003e\n\u003cli\u003eDimensions: 45 x 19 x 45 in\u003c\/li\u003e\n\u003cli\u003eWeight: 378 lbs\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat the Hybrid Pro pump brings\u003c\/h3\u003e\u003cp\u003eABAC lists the AB13-30GH on its engine range as the single Two-Stage Hybrid Pro gas model, and the T39 pump is where that name comes from. ABAC builds the Hybrid Pro pump as an aluminum pump carrying cast iron cylinders, with an aluminum head and aftercooler, and describes its inner cooling technology as managing operating temperature to reduce the risk of overheating. The practical effect is a pump that wears like cast iron where it matters while the aluminum castings keep the mass down, and that is the whole argument for this machine: 22 CFM in a 378 lb package, where the fully cast iron Ironman pumps delivering 23 to 32 CFM start at 509 lbs.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eThis is the Hybrid Pro gas model, and the trade it makes is weight against pump life. The aluminum and cast iron T39 pump brings the machine in at 378 lbs and 22 CFM. Step across to the fully cast iron Ironman pump and the numbers move together: the \u003ca href=\"\/products\/abac-abc11-30gh-11-hp-honda-gas-drive-air-compressor\"\u003e11 HP Honda ABC11-30GH\u003c\/a\u003e delivers 23 CFM at 509 lbs, the \u003ca href=\"\/products\/abac-abc13-30gh-13-hp-honda-gas-drive-air-compressor\"\u003e13 HP Honda ABC13-30GH\u003c\/a\u003e delivers 25 CFM at 519 lbs, the \u003ca href=\"\/products\/abac-abc14-30gk-14-hp-kohler-gas-drive-air-compressor\"\u003e14 HP Kohler ABC14-30GK\u003c\/a\u003e matches it at 526 lbs, and the \u003ca href=\"\/products\/abac-abc16-30gv-16-hp-vanguard-gas-drive-air-compressor\"\u003e16 HP Vanguard ABC16-30GV\u003c\/a\u003e tops the range at 32 CFM and 605 lbs. All five run 175 PSI on a 30 gallon horizontal tank. If the compressor lives on a truck and gets loaded and unloaded daily, the 130 to 230 lbs this model saves is the deciding number. If it runs hard every day in one place, the cast iron Ironman pump is the one built for it.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC rates its engine range for heavy duty work where mobility is the point and no electrical outlet is available, and rates the Hybrid Pro pump for air and water spraying, impact wrenching and screwing. In practice that means mobile service and tire trucks, construction and framing crews, fence and deck installation, roofing and siding, agricultural and farm work away from the shop, and any remote site where running an air tool matters more than finding an outlet. At 22 CFM it will keep an impact wrench, a framing nailer or a pair of air hammers fed, and the 30 gallon ASME receiver stops the pump short cycling between tool triggers.\u003c\/p\u003e\u003ch3\u003eSiting and running a gas drive\u003c\/h3\u003e\u003cp\u003eRun it outdoors or in an open bay, never in a closed shop or a van with the doors shut, because the engine exhausts carbon monoxide. Keep it level so the engine and pump oil sit where they should, leave the flywheel and belt guard clear air for cooling, and drain the tank at the end of the day. ABAC fits the EZ pull tank drain and the fully enclosed belt guard for exactly this duty cycle, where a machine gets loaded, bounced down a road and started cold again the next morning. The 12V electric start saves the rope pull on those cold mornings and the recoil backup means a flat battery does not end the shift, so check the engine oil at every fuel fill and keep a spare pump oil and air filter element on the truck.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Engine Drive range from the Atlas Copco group. See the rest of the \u003ca href=\"\/collections\/engine-driven\"\u003egas engine compressors\u003c\/a\u003e and our wider range of \u003ca href=\"\/collections\/portable-air-compressors\"\u003eportable air compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"Default Title","offer_id":54557519118611,"sku":"8090304620","price":3746.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-ab13-30gh-honda-gas-drive-air-compressor.png?v=1786378110"},{"product_id":"abac-abc11-30gh-11-hp-honda-gas-drive-air-compressor","title":"ABAC ABC11-30GH 11 HP Honda Gas Drive Ironman Air Compressor - 30 Gallon Horizontal, 175 PSI, 23 CFM","description":"\u003cp\u003eThe ABAC ABC11-30GH is the entry point into the Ironman Engine range, where the pump is full cast iron rather than an aluminum block hybrid. That extra mass is what survives job site duty: heat, dust, vibration and long runtimes. An 11 HP Honda engine drives the C1 two-stage cast iron pump to 23 CFM at a maximum 175 PSI on a 30 gallon horizontal ASME tank, which is enough air for a framing crew, a mobile tire truck, or a service body running impact tools through the day.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: ABC11-30GH\u003c\/li\u003e\n\u003cli\u003eWarthog part number: 8090303697 (ABAC part number 2020041754)\u003c\/li\u003e\n\u003cli\u003eEngine: 11 HP Honda gas\u003c\/li\u003e\n\u003cli\u003ePump: C1 two-stage, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 23 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 30 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eStarting: 12V electric start with recoil backup\u003c\/li\u003e\n\u003cli\u003eEZ pull tank drain\u003c\/li\u003e\n\u003cli\u003eDimensions: 20 x 44 x 42 in\u003c\/li\u003e\n\u003cli\u003eWeight: 509 lbs\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard, discharge valve\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the cast iron pump matters\u003c\/h3\u003e\u003cp\u003eABAC builds its gas drive machines around two pump constructions. The T39 hybrid mixes aluminum and cast iron and keeps the machine light, which is why the \u003ca href=\"\/products\/abac-ab13-30gh-13-hp-honda-gas-drive-air-compressor\"\u003eAB13-30GH\u003c\/a\u003e comes in at 378 lbs. The C1 pump on the ABC11-30GH is fully cast iron, and ABAC positions it as the premium alternative. Cast iron cylinders shed heat better and tolerate the long duty cycles that service trucks and rental fleets impose, and that is most of the reason this machine weighs 509 lbs instead of 378. If the compressor gets lifted in and out of a truck bed daily and runs in short bursts, the hybrid pump is the lighter answer. If it runs under load for hours at a time, the cast iron pump is what you are paying for.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eAcross the Ironman engine lineup the engine and the airflow move together on the same 30 gallon horizontal platform. The ABC11-30GH delivers 23 CFM at 509 lbs. The \u003ca href=\"\/products\/abac-abc13-30gh-13-hp-honda-gas-drive-air-compressor\"\u003e13 HP Honda ABC13-30GH\u003c\/a\u003e and the \u003ca href=\"\/products\/abac-abc14-30gk-14-hp-kohler-gas-drive-air-compressor\"\u003e14 HP Kohler ABC14-30GK\u003c\/a\u003e both step up to 25 CFM, and the \u003ca href=\"\/products\/abac-abc16-30gv-16-hp-vanguard-gas-drive-air-compressor\"\u003e16 HP Vanguard ABC16-30GV\u003c\/a\u003e reaches 32 CFM for sandblasting and two operator work. Where weight matters more than pump life, the \u003ca href=\"\/products\/abac-ab13-30gh-13-hp-honda-gas-drive-air-compressor\"\u003eAB13-30GH\u003c\/a\u003e uses the lighter T39 hybrid aluminum and cast iron pump at 378 lbs and 22 CFM. Choose on airflow first, then on the engine brand your crews already stock parts for.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC rates the Ironman Engine Series for hammering, spraying, grinding and nailing. On site that means framing and roofing crews, mobile tire and fleet service, utility and pipeline work, and rental fleets where the machine has to tolerate hard use and no shore power. The 30 gallon ASME receiver keeps the pump from short cycling between tool triggers, and the gas engine means no generator and no cord run on remote jobs. Electric start matters on a 509 lb machine that gets started cold several times a day, and the recoil backup means a flat battery does not end the shift.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman Engine range from the Atlas Copco group. See the rest of the \u003ca href=\"\/collections\/engine-driven\"\u003egas engine compressors\u003c\/a\u003e and our wider range of \u003ca href=\"\/collections\/portable-air-compressors\"\u003eportable air compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"Default Title","offer_id":54557519151379,"sku":"8090303697","price":3597.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc11-30gh-honda-gas-drive-air-compressor.png?v=1786378111"},{"product_id":"abac-abc13-30gh-13-hp-honda-gas-drive-air-compressor","title":"ABAC ABC13-30GH 13 HP Honda Gas Drive Ironman Air Compressor - 30 Gallon Horizontal, 175 PSI, 25 CFM","description":"\u003cp\u003eThe ABAC ABC13-30GH is the 13 HP Honda machine in the Ironman Engine range: a C1 cast iron two-stage pump turning out 25 CFM at a maximum 175 PSI, mounted on a 30 gallon horizontal ASME receiver. It is the step up from the 11 HP model for crews who keep running out of air partway through a job, and at 519 lbs it still loads onto a trailer or service body. No generator, no shore power, no cord run across the site.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: ABC13-30GH\u003c\/li\u003e\n\u003cli\u003eWarthog part number: 8090303705 (ABAC part number 2020041755)\u003c\/li\u003e\n\u003cli\u003eEngine: 13 HP Honda gas, 12V electric start with recoil backup\u003c\/li\u003e\n\u003cli\u003ePump: C1 two-stage, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 25 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 30 gallon horizontal, ASME tank and safety valves, EZ pull tank drain\u003c\/li\u003e\n\u003cli\u003eDimensions: 20 x 44 x 42 in\u003c\/li\u003e\n\u003cli\u003eWeight: 519 lbs\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard, discharge valve\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the cast iron pump matters\u003c\/h3\u003e\u003cp\u003eABAC builds its gas drive machines with two pump constructions and is explicit about the difference: the T39 hybrid pump mixes aluminum and cast iron, and the fully cast iron Ironman pump is the premium alternative. The C1 pump on the ABC13-30GH is the cast iron one. Cast iron cylinders shed heat better and tolerate the long duty cycles that service trucks, blasting work and all day fastening impose, which is most of the reason this machine weighs 519 lbs while the hybrid \u003ca href=\"\/products\/abac-ab13-30gh-13-hp-honda-gas-drive-air-compressor\"\u003eAB13-30GH\u003c\/a\u003e comes in at 378 lbs on the same 13 HP Honda engine. If the compressor gets lifted in and out of a truck bed daily and runs in short bursts, the hybrid is the lighter answer. If it runs most of the day under load, the cast iron pump is what you are paying for.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eAcross the Ironman Engine range the engine and the airflow move together. The \u003ca href=\"\/products\/abac-abc11-30gh-11-hp-honda-gas-drive-air-compressor\"\u003e11 HP Honda ABC11-30GH\u003c\/a\u003e delivers 23 CFM at 509 lbs on the same 30 gallon horizontal platform. The \u003ca href=\"\/products\/abac-abc14-30gk-14-hp-kohler-gas-drive-air-compressor\"\u003e14 HP Kohler ABC14-30GK\u003c\/a\u003e matches this machine at 25 CFM and weighs 526 lbs, so the deciding factor there is the engine brand your crews already stock parts for. The \u003ca href=\"\/products\/abac-abc16-30gv-16-hp-vanguard-gas-drive-air-compressor\"\u003e16 HP Vanguard ABC16-30GV\u003c\/a\u003e steps up to 32 CFM at 605 lbs. All four run 175 PSI on a 30 gallon tank. If weight matters more than pump life, the \u003ca href=\"\/products\/abac-ab13-30gh-13-hp-honda-gas-drive-air-compressor\"\u003e13 HP Hybrid Pro AB13-30GH\u003c\/a\u003e uses the T39 hybrid aluminum and cast iron pump to cut the machine to 378 lbs at 22 CFM, but the fully cast iron Ironman pump is the one built for daily duty.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC rates the Ironman Engine Series for hammering, nailing, grinding and spraying at remote sites, and that is exactly where this machine earns its keep: mobile service rigs, fleet and agricultural equipment maintenance, pipeline and utility crews, framing and roofing sites, and rental yards. At 25 CFM it will keep a 1 inch impact wrench, a chipping hammer or a pair of framing nailers fed, and the 30 gallon ASME receiver stops the pump short cycling between tool triggers. The 12V electric start saves the rope pull on cold mornings, and the low horizontal tank keeps the center of gravity down for loading and towing.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman Engine range from the Atlas Copco group. See the rest of the \u003ca href=\"\/collections\/engine-driven\"\u003egas engine compressors\u003c\/a\u003e and our wider range of \u003ca href=\"\/collections\/portable-air-compressors\"\u003eportable air compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"Default Title","offer_id":54557519282451,"sku":"8090303705","price":3730.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc13-30gh-honda-gas-drive-air-compressor.png?v=1786378111"},{"product_id":"abac-abc14-30gk-14-hp-kohler-gas-drive-air-compressor","title":"ABAC ABC14-30GK 14 HP Kohler Gas Drive Ironman Air Compressor - 30 Gallon Horizontal, 175 PSI, 25 CFM","description":"\u003cp\u003eThe ABAC ABC14-30GK is the Kohler powered machine in the Ironman Engine range: a 14 HP Kohler gas engine driving a cast iron two-stage pump for 25 CFM at a maximum 175 PSI, mounted on a 30 gallon horizontal ASME receiver. It matches the airflow of the 13 HP Honda model, so the reason to choose it is the engine badge. Fleets that already stock Kohler filters, plugs and carburetor parts keep one parts shelf instead of two.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: ABC14-30GK\u003c\/li\u003e\n\u003cli\u003eWarthog part number: 8090303713 (ABAC part number 2020041756)\u003c\/li\u003e\n\u003cli\u003eEngine: 14 HP Kohler gas\u003c\/li\u003e\n\u003cli\u003ePump: C1 two-stage, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 25 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 30 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eStarting: 12V electric start with recoil backup\u003c\/li\u003e\n\u003cli\u003eEZ pull tank drain\u003c\/li\u003e\n\u003cli\u003eDimensions: 21 x 46 x 44 in\u003c\/li\u003e\n\u003cli\u003eWeight: 526 lbs\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard, discharge valve\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the cast iron pump matters\u003c\/h3\u003e\u003cp\u003eABAC builds its gas drive compressors with two different pump constructions and treats the fully cast iron Ironman pump as the premium one. The alternative, the T39 hybrid, mixes aluminum and cast iron and appears on the lighter \u003ca href=\"\/products\/abac-ab13-30gh-13-hp-honda-gas-drive-air-compressor\"\u003eAB13-30GH\u003c\/a\u003e, which delivers 22 CFM at 378 lbs. The C1 pump on the ABC14-30GK is cast iron throughout. Cast iron cylinders shed heat better and tolerate the long duty cycles that service trucks and rental fleets impose, and that is most of the reason this machine weighs 526 lbs rather than 378. If the compressor runs in short bursts and gets lifted in and out of a truck bed every day, the hybrid pump is the lighter answer. If it runs most of the day under load, the cast iron pump is what you are paying for.\u003c\/p\u003e\u003ch3\u003eStandard features\u003c\/h3\u003e\u003cp\u003eEvery machine in the Ironman Engine range carries the same hardware: a fully enclosed belt guard, 12V electric start with a recoil backup, and the EZ pull tank drain that lets an operator bleed condensate without crawling under the receiver with a wrench. The ASME coded tank and safety valves are standard, the units are assembled in the USA, and they carry a 2 year full warranty.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eAcross the Ironman Engine range the engine and the airflow move together. The \u003ca href=\"\/products\/abac-abc11-30gh-11-hp-honda-gas-drive-air-compressor\"\u003e11 HP Honda ABC11-30GH\u003c\/a\u003e delivers 23 CFM at 509 lbs, the \u003ca href=\"\/products\/abac-abc13-30gh-13-hp-honda-gas-drive-air-compressor\"\u003e13 HP Honda ABC13-30GH\u003c\/a\u003e delivers 25 CFM at 519 lbs, and the \u003ca href=\"\/products\/abac-abc16-30gv-16-hp-vanguard-gas-drive-air-compressor\"\u003e16 HP Vanguard ABC16-30GV\u003c\/a\u003e steps up to 32 CFM at 605 lbs. All four run 175 PSI on a 30 gallon horizontal tank. Footprint splits the range in two: the 11 and 13 HP Honda machines measure 20 x 44 x 42 in, while the ABC14-30GK and the 16 HP Vanguard share a slightly larger 21 x 46 x 44 in frame. That matters if the compressor lives in a fixed cradle on a service body. Pick on CFM first, then on the engine brand your crews already service, then on the space you have to mount it.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC rates the Ironman Engine Series for hammering, spraying, grinding and nailing, and builds it for heavy duty work where mobility is the point and there is no electrical outlet to plug into. In practice that means contractor and utility fleets standardized on Kohler power, mobile service rigs, pipeline and tower crews, rental yards, and framing or roofing sites with no generator and no shore power. At 25 CFM it will keep a pair of impact wrenches, a chipping hammer or a grinder fed, and the 30 gallon ASME receiver stops the pump short cycling between tool triggers. The 12V electric start matters on cold mornings when nobody wants to pull a rope, and the recoil backup means a flat battery does not end the shift. If the work is sandblasting or two operators running air at once, step up to the 32 CFM Vanguard machine instead.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman Engine range from the Atlas Copco group. See the rest of the \u003ca href=\"\/collections\/engine-driven\"\u003egas engine compressors\u003c\/a\u003e and our wider range of \u003ca href=\"\/collections\/portable-air-compressors\"\u003eportable air compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"Default Title","offer_id":54557521903891,"sku":"8090303713","price":3398.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc14-30gk-kohler-gas-drive-air-compressor.png?v=1786383749"},{"product_id":"abac-abc16-30gv-16-hp-vanguard-gas-drive-air-compressor","title":"ABAC ABC16-30GV 16 HP Vanguard Gas Drive Ironman Air Compressor - 30 Gallon Horizontal, 175 PSI, 32 CFM","description":"\u003cp\u003eThe ABAC ABC16-30GV sits at the top of the Ironman Engine Series: a 16 HP Briggs and Stratton Vanguard engine driving a two-stage cast iron pump for 32 CFM at a maximum 175 PSI. That is enough continuous air for sandblasting, large impact tools, or two operators working at once without a pressure drop, which is why crews reach for it when a 25 CFM machine keeps falling behind. ABAC builds the Ironman Engine Series for heavy duty work where mobility matters and there is no electrical outlet to plug into.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: ABC16-30GV\u003c\/li\u003e\n\u003cli\u003eWarthog part number: 8090304075 (ABAC part number 2020041792)\u003c\/li\u003e\n\u003cli\u003eEngine: 16 HP Vanguard gas\u003c\/li\u003e\n\u003cli\u003ePump: C2 two-stage, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 32 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 30 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eStarting: 12V electric start with recoil backup\u003c\/li\u003e\n\u003cli\u003eEZ pull tank drain\u003c\/li\u003e\n\u003cli\u003eDimensions: 21 x 46 x 44 in\u003c\/li\u003e\n\u003cli\u003eWeight: 605 lbs\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard, discharge valve\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the cast iron pump matters\u003c\/h3\u003e\u003cp\u003eABAC offers two pump constructions on its gas drive machines. The hybrid T39 pump mixes aluminum and cast iron and shows up on the lighter \u003ca href=\"\/products\/abac-ab13-30gh-13-hp-honda-gas-drive-air-compressor\"\u003eAB13-30GH\u003c\/a\u003e, which delivers 22 CFM at 378 lbs. The Ironman pump on the ABC16-30GV is fully cast iron, and ABAC positions it as the premium alternative. Cast iron cylinders shed heat better and tolerate the long duty cycles that service trucks and blasting work impose, which is most of the reason this machine weighs 605 lbs instead of 378. If the compressor runs in short bursts and gets lifted in and out of a truck bed daily, the hybrid pump is the lighter answer. If it runs most of the day under load, the cast iron pump is what you are paying for.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the Ironman engine lineup the engine and the pump scale together. The \u003ca href=\"\/products\/abac-abc11-30gh-11-hp-honda-gas-drive-air-compressor\"\u003e11 HP Honda ABC11-30GH\u003c\/a\u003e delivers 23 CFM at 509 lbs, and the \u003ca href=\"\/products\/abac-abc13-30gh-13-hp-honda-gas-drive-air-compressor\"\u003e13 HP Honda ABC13-30GH\u003c\/a\u003e and the \u003ca href=\"\/products\/abac-abc14-30gk-14-hp-kohler-gas-drive-air-compressor\"\u003e14 HP Kohler ABC14-30GK\u003c\/a\u003e both deliver 25 CFM at 175 PSI and weigh 519 and 526 lbs. The ABC16-30GV steps up to 32 CFM at 605 lbs, sharing the same 21 x 46 x 44 in footprint as the Kohler machine. Every machine in the Ironman engine range shares the fully enclosed belt guard and the 12V electric and recoil start, so choose on airflow first, then on the engine brand your crews already stock parts for.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC rates the Ironman Engine Series for hammering, spraying, grinding and nailing. In practice that means sandblasting, heavy equipment service in the field, pipeline and utility crews, rental fleets, and multi operator job sites where 25 CFM is not enough. The 30 gallon ASME receiver keeps the pump from short cycling between tool triggers, and the gas engine means no generator and no shore power on remote work. Electric start matters on a 605 lb machine that gets moved between sites and started cold several times a day, and the recoil backup means a flat battery does not end the shift.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman Engine range from the Atlas Copco group. See the rest of the \u003ca href=\"\/collections\/engine-driven\"\u003egas engine compressors\u003c\/a\u003e and our wider range of \u003ca href=\"\/collections\/portable-air-compressors\"\u003eportable air compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"Default Title","offer_id":54557521936659,"sku":"8090304075","price":4957.0,"currency_code":"USD","in_stock":true}]},{"product_id":"abac-abc10-10-hp-120-gallon-horizontal-ironman-air-compressor","title":"ABAC ABC10-23120H 10 HP Two-Stage Ironman Air Compressor - 120 Gallon Horizontal, 175 PSI, 32 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC10-23120H is the 10 HP Ironman on a 120 gallon horizontal ASME tank, driving the C2 two-stage cast iron pump to 32 CFM at a maximum 175 PSI. The horizontal layout sits low and long, 74 in from end to end but only 50 in tall, which suits shops that would rather run the compressor along a wall or under a mezzanine than give up vertical footprint. This is a three-phase machine only. Choose 230V three-phase (ABC10-23120H), 460V three-phase (ABC10-43120H), or 575V three-phase (ABC10-53120H).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC10-23120H \/ ABC10-43120H \/ ABC10-53120H\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP\u003c\/li\u003e\n\u003cli\u003ePump: C2 two-stage, four cylinder V-shape, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 32 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/3\/60, 460\/3\/60, or 575\/3\/60\u003c\/li\u003e\n\u003cli\u003eDimensions: 27 x 74 x 50 in (L x W x H)\u003c\/li\u003e\n\u003cli\u003eWeight: 728 lbs\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat the Ironman pump buys you\u003c\/h3\u003e\u003cp\u003eABAC builds the Ironman range around a four cylinder, V-shaped, fully cast iron pump, and that is the whole reason this machine exists alongside lighter aluminum and hybrid builds. Cast iron cylinders shed heat instead of storing it, so the pump tolerates the long loaded stretches that a production shop imposes, and the V layout spreads four cylinders across two stages for a steadier torque pull on the motor. The practical result is a compressor you can size to the shift rather than to the job: at 32 CFM and 175 PSI it holds line pressure while several tools draw at once, and the 120 gallon receiver absorbs the peaks so the motor starts less often. ABAC backs the Ironman Simplex range with a two year warranty.\u003c\/p\u003e\u003ch3\u003eModels, part numbers and configurations\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eSKU\u003c\/th\u003e\n\u003cth\u003eVoltage\u003c\/th\u003e\n\u003cth\u003eCFM at 175 PSI\u003c\/th\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eABC10-23120H\u003c\/td\u003e\n\u003ctd\u003e8090303952\u003c\/td\u003e\n\u003ctd\u003e230V \/ 3 phase \/ 60 Hz\u003c\/td\u003e\n\u003ctd\u003e32\u003c\/td\u003e\n\u003ctd\u003e728 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eABC10-43120H\u003c\/td\u003e\n\u003ctd\u003e8090303994\u003c\/td\u003e\n\u003ctd\u003e460V \/ 3 phase \/ 60 Hz\u003c\/td\u003e\n\u003ctd\u003e32\u003c\/td\u003e\n\u003ctd\u003e728 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eABC10-53120H\u003c\/td\u003e\n\u003ctd\u003e8090304034\u003c\/td\u003e\n\u003ctd\u003e575V \/ 3 phase \/ 60 Hz\u003c\/td\u003e\n\u003ctd\u003e32\u003c\/td\u003e\n\u003ctd\u003e728 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cem\u003eABAC part numbers: 2020041780 (230V) and 2020041784 (460V).\u003c\/em\u003e\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eSame pump, same 32 CFM, different footprint. The \u003ca href=\"\/products\/abac-abc10-10-hp-120-gallon-vertical-ironman-air-compressor\"\u003eABC10-23120V vertical\u003c\/a\u003e stands 74 in tall on a 30 x 41 in base and weighs 765 lbs, trading floor space for height. This horizontal build runs 74 in long and 50 in tall at 728 lbs, which is the one to pick under a mezzanine or a low ceiling. The \u003ca href=\"\/products\/abac-abc10-ff-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC10 horizontal Full Feature\u003c\/a\u003e is the same machine with ABAC's protection package already fitted: automatic tank drain, low oil level automatic shut off, and a belt guard aftercooler. Buy the Full Feature if nobody on staff will remember to drain the tank or watch the oil, and buy this one if you already have that discipline and a dryer downstream. A step down, the \u003ca href=\"\/products\/abac-abc7-v2-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003e7.5 HP ABC7-2180V2\u003c\/a\u003e delivers 24 CFM on an 80 gallon vertical tank. If 32 CFM is already marginal, the \u003ca href=\"\/products\/abac-abc10-duplex-20-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC10-23120HD duplex\u003c\/a\u003e puts two 10 HP pumps on one 120 gallon horizontal tank for 64 CFM and lets you service one side while the other keeps air on the line.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC rates the Ironman range for equipment operation, grinding, hammering, fastening, orbital sanding, spraying and tire inflation, and points it at auto body and repair shops and at metal and wood workshops. In practice that means production floors, fabrication and welding bays, truck and fleet maintenance, tire shops running multiple lifts, and any operation where several air tools or a plasma cutter draw at the same time and the compressor needs to hold pressure through the shift rather than recover between jobs.\u003c\/p\u003e\u003ch3\u003eInstallation and air treatment\u003c\/h3\u003e\u003cp\u003ePlan for 10 HP three-phase service and a correctly sized disconnect; there is no single-phase option in this frame size. Leave room at both ends of a 74 in tank for the drain and the service side of the pump, and keep the intake away from paint fog and grinding dust. If the air feeds paint, plasma or pneumatic controls, add a refrigerated dryer rated above the compressor's 32 CFM. The \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eABAC COOL 50\u003c\/a\u003e is rated 50 CFM and runs on a standard 115V single-phase outlet, so it drops in beside the compressor without new wiring. Drain the receiver daily unless you fit an automatic drain, and keep a spare set of filters and pump oil on the shelf.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the Atlas Copco group. The extra 120 gallons of storage over an 80 gallon build cuts motor starts and holds a steadier line pressure, while the horizontal tank keeps overall height down where ceiling clearance is tight. See the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and the full range of \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 3-Phase","offer_id":54637280428307,"sku":"8090303952","price":4512.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54637280461075,"sku":"8090303994","price":4512.0,"currency_code":"USD","in_stock":true},{"title":"575V 3-Phase","offer_id":54637280493843,"sku":"8090304034","price":4735.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc10-120-gallon-horizontal-ironman-air-compressor.png?v=1789403336"},{"product_id":"abac-abc10-ff-10-hp-120-gallon-horizontal-ironman-air-compressor","title":"ABAC ABC10-23120HFF 10 HP Two-Stage Ironman Air Compressor - 120 Gallon Horizontal Full Feature, 175 PSI, 32 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC10-23120HFF puts the 10 HP Ironman on a \u003ca href=\"\/collections\/horizontal-air-compressor-tanks\"\u003e120 gallon horizontal ASME tank\u003c\/a\u003e and adds ABAC's Full Feature protection package, so the machine looks after itself between shifts. The C2 four cylinder V shape cast iron pump delivers 32 CFM at a maximum 175 PSI. The horizontal layout sits low and long at 50 inches tall, which suits shops that would rather run the compressor along a wall or under a mezzanine than give up floor space to a vertical footprint. This is a three-phase machine only. Choose 230V three-phase (ABC10-23120HFF), 460V three-phase (ABC10-43120HFF), or 575V three-phase (ABC10-53120HFF).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC10-23120HFF \/ ABC10-43120HFF \/ ABC10-53120HFF\u003c\/li\u003e\n\u003cli\u003eFull Feature package: automatic tank drain, low oil level automatic shut off, and belt guard aftercooler\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP\u003c\/li\u003e\n\u003cli\u003ePump: C2 two-stage, four cylinder V shape, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 32 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/3\/60, 460\/3\/60, or 575\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 728 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 27 x 74 x 50 in\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guard, discharge valve, magnetic starter\u003c\/li\u003e\n\u003cli\u003eAssembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eThe same 10 HP Ironman and the same 32 CFM at 175 PSI are also sold on a vertical receiver. The \u003ca href=\"\/products\/abac-abc10-ff-10-hp-120-gallon-vertical-ironman-air-compressor\"\u003e120 gallon vertical Full Feature\u003c\/a\u003e is 765 lbs at 30 x 41 x 74 in and gives back the floor where there is ceiling height to spare, while this horizontal build is 728 lbs at 27 x 74 x 50 in and keeps overall height down where clearance is tight. Airflow is identical, so pick on the space you have. If the Full Feature additions are not needed, the \u003ca href=\"\/products\/abac-abc10-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003estandard ABC10 horizontal\u003c\/a\u003e is the same pump and tank without the automatic drain, low oil shut off or aftercooler. Below this sits the \u003ca href=\"\/products\/abac-abc7-v2-ff-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003e7.5 HP ABC7-2180V2FF\u003c\/a\u003e at 24 CFM on an 80 gallon vertical tank, which is the right call when the duty is one or two tools at a time rather than a full bay. Alongside it, the \u003ca href=\"\/products\/abac-abc5-duplex-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC5-21120HD duplex\u003c\/a\u003e reaches the same 32 CFM from two 5 HP pumps on one 120 gallon horizontal tank, which buys alternating control and a second pump to fall back on rather than more air.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction shops, fabrication and welding bays, truck and fleet maintenance, tire shops running multiple lifts, and any operation where several \u003ca href=\"\/collections\/tools\"\u003eair tools\u003c\/a\u003e or a plasma cutter draw at the same time and the compressor needs to hold pressure through the shift rather than recover between jobs. The 120 gallon receiver cuts motor starts and holds a steadier line pressure than an 80 gallon build, which matters most on intermittent duty where a smaller tank would short cycle the pump. The Full Feature build suits shops that would rather not rely on someone remembering to drain the tank or check the oil.\u003c\/p\u003e\u003cp\u003eThe belt guard aftercooler drops discharge temperature before the air reaches the tank, so less condensate is carried downstream into tools and filters. On a 32 CFM machine feeding paint, plasma or pneumatic instruments, pair it with a \u003ca href=\"\/collections\/air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e sized at or above 32 CFM and a filter regulator at the drop. Part of ABAC's Ironman cast iron range from the Atlas Copco group. See the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 3-Phase","offer_id":54638092681491,"sku":"8090303960","price":5324.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54638092714259,"sku":"8090304000","price":5324.0,"currency_code":"USD","in_stock":true},{"title":"575V 3-Phase","offer_id":54638092747027,"sku":"8090304042","price":5595.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc10-120-gallon-horizontal-full-feature-air-compressor.png?v=1788228625"},{"product_id":"abac-abc5-duplex-10-hp-120-gallon-horizontal-ironman-air-compressor","title":"ABAC ABC5-21120HD 10 HP Ironman Duplex Air Compressor - 120 Gallon Horizontal, 175 PSI, 32 CFM C1 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC5-21120HD is the Ironman duplex built around redundancy: two independent 5 HP motor and pump assemblies on a single 120 gallon horizontal ASME tank. Each side runs a C1 two-stage cast iron pump rated 16 CFM, for 32 CFM combined at a maximum 175 PSI. Because the two assemblies are separate, one can come down for service while the other keeps air on the line, which is the reason most shops step up to a duplex rather than buying one larger simplex machine. Choose 230V single-phase (ABC5-21120HD), 230V three-phase (ABC5-23120HD), or 460V three-phase (ABC5-43120HD).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC5-21120HD \/ ABC5-23120HD \/ ABC5-43120HD\u003c\/li\u003e\n\u003cli\u003ePower: 10 HP total (2 x 5 HP)\u003c\/li\u003e\n\u003cli\u003ePumps: two C1 two-stage pumps, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 32 CFM combined (16 CFM per pump)\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60, 230\/3\/60, or 460\/3\/60\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guards\u003c\/li\u003e\n\u003cli\u003eWeight: 1120 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 25 x 79 x 52 in (230V single-phase), 25 x 79 x 55 in (three-phase)\u003c\/li\u003e\n\u003cli\u003eAssembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a duplex instead of one bigger compressor\u003c\/h3\u003e\u003cp\u003eA duplex buys two things a single machine cannot. The first is uptime: a failed pump, a belt change, or an oil service takes half the capacity offline instead of all of it, so the floor keeps working. The second is staging. Under light or intermittent demand only one side needs to run, and an alternating control shares the hours between the two pumps rather than loading one of them all day. Each pump then runs cooler, rests longer, and reaches its service intervals later than a single pump doing the same total work. Both sides use the fully cast iron C1 pump of the Ironman range, where the extra mass absorbs heat and damps vibration through long run times, and both are two-stage, so 175 PSI arrives in two compression steps with cooling in between instead of one hot single-stage squeeze.\u003c\/p\u003e\u003ch3\u003eSizing and how it compares\u003c\/h3\u003e\u003cp\u003eSize on CFM, not on horsepower. 32 CFM covers a multi-bay shop running impact wrenches, ratchets, grinders and a spray gun at the same time. If the duty is the same but cast iron is more pump than the work needs, the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-ab5-duplex-10-hp-120-gallon-horizontal-air-compressor\"\u003eAB5-21120D\u003c\/a\u003e is the hybrid T39 pump duplex on the same 120 gallon platform. Stepping up, the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc7-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e15 HP ABC7-21120HD\u003c\/a\u003e pairs two 7.5 HP sides for 42 CFM, and the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc10-duplex-20-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e20 HP ABC10-23120HD\u003c\/a\u003e reaches 64 CFM. If redundancy is not the point and 16 CFM is enough, the single-pump \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc5-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003e5 HP ABC5-2180V\u003c\/a\u003e does the same work on an 80 gallon vertical tank in a far smaller footprint.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction shops, multi-bay service and tire centers, fabrication and welding bays, body shops, and fleet maintenance operations where several air tools draw at once and a compressor going down stops the whole floor. It also suits a facility with a process that cannot tolerate an air outage, where the second pump is insurance rather than extra capacity. At 79 inches long the horizontal tank runs along a wall and keeps the overhead clear.\u003c\/p\u003e\u003ch3\u003ePower, installation and air quality\u003c\/h3\u003e\u003cp\u003eTake three-phase power if the panel has it, since three-phase motors start easier and run cooler on a compressor that cycles all day, and the 460V build keeps the wire size down on a long run. Each side draws its own load, so size the circuit for both running together even if the control normally alternates them. Leave clearance around the belt guards and the flywheels for cooling air and for service access, and plan the drain: a 120 gallon receiver collects real water. Air leaves any piston compressor hot and saturated, so pair it with a \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e ahead of a paint booth, a plasma table, or any tool line you would rather not run water through.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. See the rest of our \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/5-to-15-hp-piston-air-compressors\"\u003e5 to 15 HP piston air compressors\u003c\/a\u003e and the full \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/piston-air-compressors\"\u003episton air compressor\u003c\/a\u003e range.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54698452451603,"sku":"8090303721","price":7271.0,"currency_code":"USD","in_stock":true},{"title":"230V 3-Phase","offer_id":54698452484371,"sku":"8090303739","price":7271.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54698452517139,"sku":"8090303747","price":7451.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc5-duplex-120-gallon-horizontal-ironman-air-compressor.png?v=1789403336"},{"product_id":"abac-abc7-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor","title":"ABAC ABC7-21120HD 15 HP Ironman Duplex Air Compressor - 120 Gallon Horizontal, 175 PSI, 42 CFM C1 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC7-21120HD is the Ironman duplex built for shops that cannot afford an air outage: two independent 7.5 HP motor and pump assemblies on a single 120 gallon horizontal ASME tank. Each side runs a C1 two-stage cast iron pump rated 21 CFM, for 42 CFM combined at a maximum 175 PSI. Because the two assemblies are separate, one can come down for service while the other keeps air on the line, which is the reason most shops step up to a duplex rather than buying one larger simplex machine. Choose 230V single-phase (ABC7-21120HD), 230V three-phase (ABC7-23120HD), 460V three-phase (ABC7-43120HD), or 575V three-phase (ABC7-53120HD).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC7-21120HD \/ ABC7-23120HD \/ ABC7-43120HD \/ ABC7-53120HD\u003c\/li\u003e\n\u003cli\u003ePower: 15 HP total (2 x 7.5 HP)\u003c\/li\u003e\n\u003cli\u003ePumps: two C1 two-stage pumps, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 42 CFM combined (21 CFM per pump)\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60, 230\/3\/60, 460\/3\/60, or 575\/3\/60\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guards\u003c\/li\u003e\n\u003cli\u003eAlternating control, dual control for full output, fully programmable control panel\u003c\/li\u003e\n\u003cli\u003eWeight: 1138 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 25 x 79 x 55 in\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a duplex instead of one bigger compressor\u003c\/h3\u003e\u003cp\u003eA duplex buys two things a single machine cannot. The first is uptime: a failed pump, a belt change, or an oil service takes half the capacity offline instead of all of it, so the floor keeps working. The second is staging. Under light or intermittent demand the alternating control runs one side at a time and shares the hours between the two pumps rather than loading one of them all day; when demand climbs, dual control brings both sides on for the full 42 CFM. Each pump then runs cooler, rests longer, and reaches its service intervals later than a single pump doing the same total work. Both sides use the fully cast iron C1 pump of the Ironman range, where the extra mass absorbs heat and damps vibration through long run times, and both are two-stage, so 175 PSI arrives in two compression steps with cooling in between instead of one hot single-stage squeeze.\u003c\/p\u003e\u003ch3\u003eSizing and how it compares\u003c\/h3\u003e\u003cp\u003eSize on CFM, not on horsepower. 42 CFM supports a busy multi-bay shop running impact wrenches, ratchets, grinders, a sandblast cabinet and a spray gun without the pressure sagging between bays. If 32 CFM is enough, the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc5-duplex-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e10 HP ABC5-21120HD\u003c\/a\u003e is the same platform with two 5 HP sides. If the duty is the same but cast iron is more pump than the work needs, the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-ab7-duplex-15-hp-120-gallon-horizontal-air-compressor\"\u003eAB7-21120D\u003c\/a\u003e is the hybrid T39 pump duplex at 15 HP. Within the Ironman range the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc7-v2-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC7-2112DH2P\u003c\/a\u003e pairs two C2 pumps for 52 CFM at the same 15 HP, and the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc10-duplex-20-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e20 HP ABC10-23120HD\u003c\/a\u003e reaches 64 CFM. If redundancy is not the point and 21 CFM is enough, the single-pump \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc7-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003e7.5 HP ABC7-2180V\u003c\/a\u003e does the same per-side work on an 80 gallon vertical tank in a far smaller footprint.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction shops, multi-bay service and tire centers, fabrication and welding bays, body shops, and fleet maintenance operations where several air tools draw at once and a compressor going down stops the whole floor. It also suits a facility with a process that cannot tolerate an air outage, where the second pump is insurance rather than extra capacity. At 79 inches long the horizontal tank runs along a wall and keeps the overhead clear.\u003c\/p\u003e\u003ch3\u003ePower, installation and air quality\u003c\/h3\u003e\u003cp\u003eTake three-phase power if the panel has it, since three-phase motors start easier and run cooler on a compressor that cycles all day, and the 460V or 575V build keeps the wire size down on a long run. Each side draws its own load, so size the circuit for both running together even if the control normally alternates them. Leave clearance around the belt guards and the flywheels for cooling air and for service access, and plan the drain: a 120 gallon receiver collects real water. Air leaves any piston compressor hot and saturated, so pair it with a \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e ahead of a paint booth, a plasma table, or any tool line you would rather not run water through.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. See the rest of our \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/5-to-15-hp-piston-air-compressors\"\u003e5 to 15 HP piston air compressors\u003c\/a\u003e and the full \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/piston-air-compressors\"\u003episton air compressor\u003c\/a\u003e range.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54698847207699,"sku":"8090303754","price":7385.0,"currency_code":"USD","in_stock":true},{"title":"230V 3-Phase","offer_id":54698847240467,"sku":"8090303762","price":7385.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54698847273235,"sku":"8090303770","price":7566.0,"currency_code":"USD","in_stock":true},{"title":"575V 3-Phase","offer_id":54698847306003,"sku":"8090303788","price":7747.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc7-duplex-120-gallon-horizontal-ironman-air-compressor.png?v=1789403336"},{"product_id":"abac-abc10-duplex-20-hp-120-gallon-horizontal-ironman-air-compressor","title":"ABAC ABC10-23120HD 20 HP Ironman Duplex Air Compressor - 120 Gallon Horizontal, 175 PSI, 64 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC10 Ironman duplex mounts two independent 10 HP motor and pump assemblies on a single 120 gallon horizontal ASME tank. Each side runs a C2 two-stage cast iron pump rated 32 CFM, for 64 CFM combined at a maximum 175 PSI. Because the two assemblies are separate, one can come down for service while the other keeps air on the line, which is the reason most shops step up to a duplex in the first place. Choose 230V three-phase (ABC10-23120HD), 460V three-phase (ABC10-43120HD), or 575V three-phase (ABC10-53120HD).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC10-23120HD \/ ABC10-43120HD \/ ABC10-53120HD\u003c\/li\u003e\n\u003cli\u003ePower: 20 HP total (2 x 10 HP)\u003c\/li\u003e\n\u003cli\u003ePumps: two C2 two-stage pumps, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 64 CFM combined (32 CFM per pump)\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/3\/60, 460\/3\/60, or 575\/3\/60\u003c\/li\u003e\n\u003cli\u003eShipping weight: 1302 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 25 x 80 x 50 in\u003c\/li\u003e\n\u003cli\u003eAlternating control, so the lead pump rotates and run time is shared\u003c\/li\u003e\n\u003cli\u003eDual control, so both pumps run together when demand spikes\u003c\/li\u003e\n\u003cli\u003eFully programmable control panel\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eHow the duplex control works\u003c\/h3\u003e\u003cp\u003eThe two assemblies are not simply bolted to one tank and left to fight each other. The programmable panel alternates which pump leads, so neither side accumulates all the hours and both wear at the same rate. When demand climbs past what one pump can hold, the panel brings the second one in alongside it and the machine delivers the full 64 CFM. That is what separates a duplex from a single 20 HP machine: at light load it behaves like a 10 HP compressor and runs cool instead of short cycling a large pump, and at peak load it has the whole 64 CFM available. The same arrangement is what keeps the shop running when one side needs a valve plate or a belt, since the panel can be set to run on the healthy pump alone.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eAcross the Ironman duplex range the pump pair sets the airflow and the receiver sets how long those pumps rest between draws. The \u003ca href=\"\/products\/abac-abc5-duplex-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e10 HP ABC5-21120HD\u003c\/a\u003e pairs two C1 pumps for 32 CFM on this same 120 gallon horizontal tank, and the \u003ca href=\"\/products\/abac-abc7-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e15 HP ABC7-21120HD\u003c\/a\u003e reaches 42 CFM. The \u003ca href=\"\/products\/abac-abc10-duplex-20-hp-200-gallon-horizontal-ironman-air-compressor\"\u003eABC10-23200HD\u003c\/a\u003e is this identical 64 CFM pair on a 200 gallon receiver, worth the extra floor space where draws are heavy and intermittent, and it shares the same 25 x 80 in footprint on the floor. If redundancy is not the point and 32 CFM covers the floor, the single pump \u003ca href=\"\/products\/abac-abc10-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC10-23120H\u003c\/a\u003e uses the same C2 pump on the same 120 gallon tank for less money and less footprint.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction shops, multi bay service centers, fabrication and welding bays, auto body shops, and fleet maintenance operations where several air tools draw at once and a compressor going down stops the whole floor. A duplex also suits a plant whose demand swings through the day: one side carries the quiet hours while the second is available for the shifts when every bay is working, instead of one large machine short cycling through both. ABAC rates the Ironman Duplex range for tire inflation, hammering, grinding, fastening, orbital sanding and running air operated equipment. The 575V option matters on older industrial services where stepping down to 460V would mean a transformer.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eAll three versions are three-phase only, so confirm the panel before ordering and size the feeder to the combined nameplate rather than to one motor. At 1302 lbs on a 25 x 80 in footprint the machine wants a level slab and clearance at both ends of the tank for belt guard access and for the drains. Plan a timed or automatic drain, because a 120 gallon receiver carrying 64 CFM of two-stage air collects condensate faster than anyone remembers to crack a petcock. Keep the room ventilated and give the belt guards room to breathe, since two pumps put twice the heat into the same space.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the Atlas Copco group. A duplex pair delivers the output of a larger single machine while spreading run time across two pumps, which keeps each one cooler and shortens recovery under heavy demand. Two-stage air at 175 PSI carries a shop floor's worth of moisture, so plan on a refrigerated dryer such as the \u003ca href=\"\/products\/abac-cool-100-refrigerated-air-dryer-230v\"\u003eABAC COOL 100\u003c\/a\u003e downstream of the tank, sized with headroom over the 64 CFM the pumps deliver. See the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our full range of \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 3-Phase","offer_id":54698949312787,"sku":"8090304083","price":8765.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54698949345555,"sku":"8090304109","price":8765.0,"currency_code":"USD","in_stock":true},{"title":"575V 3-Phase","offer_id":54698949378323,"sku":"8090304125","price":8946.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc10-duplex-120-gallon-horizontal-ironman-air-compressor.png?v=1789403336"},{"product_id":"abac-abc10-duplex-20-hp-200-gallon-horizontal-ironman-air-compressor","title":"ABAC ABC10-23200HD 20 HP Ironman Duplex Air Compressor - 200 Gallon Horizontal, 175 PSI, 64 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC10-23200HD Ironman duplex mounts two independent 10 HP motor and pump assemblies on a single 200 gallon horizontal ASME tank. Each side runs a C2 two-stage cast iron pump rated 32 CFM, for 64 CFM combined at a maximum 175 PSI. Because the two assemblies are separate, one can come down for service while the other keeps air on the line, which is the reason most shops step up to a duplex in the first place. Choose 230V three-phase (ABC10-23200HD) or 460V three-phase (ABC10-43200HD).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC10-23200HD (230V) \/ ABC10-43200HD (460V)\u003c\/li\u003e\n\u003cli\u003ePower: 20 HP total (2 x 10 HP)\u003c\/li\u003e\n\u003cli\u003ePumps: two C2 two-stage pumps, cast iron cylinders with aluminum head and aftercooler\u003c\/li\u003e\n\u003cli\u003eAir delivery: 64 CFM combined (32 CFM per pump)\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 200 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/3\/60 or 460\/3\/60\u003c\/li\u003e\n\u003cli\u003eShipping weight: 1646 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 25 x 80 x 50 in\u003c\/li\u003e\n\u003cli\u003eAlternating control, so the lead pump rotates and run time is shared\u003c\/li\u003e\n\u003cli\u003eDual control, so both pumps run together when demand spikes\u003c\/li\u003e\n\u003cli\u003eFully programmable control panel\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the 200 gallon receiver\u003c\/h3\u003e\u003cp\u003eThis is the same 64 CFM pump pair that sits on the \u003ca href=\"\/products\/abac-abc10-duplex-20-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e120 gallon ABC10-23120HD\u003c\/a\u003e, on a receiver with 80 more gallons of storage. The larger tank is worth the floor space wherever the draw is heavy and intermittent: a plasma table, a blast cabinet, or four or five bays that all reach for air at once. Stored air absorbs those peaks, so the pumps start less often, run longer when they do start, and spend more time cool. On a lighter or steadier load the 120 gallon version does the same work in a shorter footprint, and both machines ship at 25 x 80 inches on the floor.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eAcross the Ironman duplex range the pump pair sets the airflow and the tank sets how long the pumps rest between draws. The \u003ca href=\"\/products\/abac-abc5-duplex-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e10 HP ABC5-21120HD\u003c\/a\u003e pairs two C1 pumps for 32 CFM, and the \u003ca href=\"\/products\/abac-abc7-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e15 HP ABC7-21120HD\u003c\/a\u003e reaches 42 CFM, both on a 120 gallon horizontal tank. If redundancy is not the point and 32 CFM covers the floor, the single pump \u003ca href=\"\/products\/abac-abc10-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC10-23120H\u003c\/a\u003e uses the same C2 pump for a lower installed cost. This 200 gallon duplex is the top of the Ironman piston range, and the next step beyond it is a rotary screw rated for 100 percent duty rather than a larger piston machine.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction shops, multi bay service centers, fabrication and welding bays, auto body shops, and fleet maintenance operations where several air tools draw at once and a compressor going down stops the whole floor. Alternating control also suits a plant whose demand swings widely through the day: one pump carries the quiet hours and the second cuts in when every bay is working, instead of a single large machine short cycling through both. Typical tool work includes tire inflation, hammering, grinding, fastening, orbital sanding and running air operated equipment.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eBoth versions are three-phase only, so confirm the panel before ordering and size the feeder to the combined nameplate rather than to one motor. Leave room at both ends of the tank for belt guard access and for the two drains, and plan a timed or automatic drain on a receiver this size because 200 gallons collects a lot of condensate. Two-stage air at 175 PSI leaves a shop floor's worth of moisture to deal with, so pair it with a \u003ca href=\"\/products\/abac-cool-100-refrigerated-air-dryer-230v\"\u003eCOOL 100 refrigerated air dryer\u003c\/a\u003e downstream of the tank, sized with headroom over the 64 CFM the pumps deliver.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the Atlas Copco group. A duplex pair delivers the output of a larger single machine while spreading run time across two pumps, which keeps each one cooler and shortens recovery under heavy demand. See the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our full range of \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 3-Phase","offer_id":54699181408531,"sku":"8090304091","price":9329.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54699181441299,"sku":"8090304117","price":9599.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc10-duplex-200-gallon-horizontal-ironman-air-compressor.png?v=1789404495"},{"product_id":"abac-abc7-v2-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor","title":"ABAC ABC7-2112DH2P 15 HP Ironman Duplex Air Compressor - 120 Gallon Horizontal, 175 PSI, 52 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC7-2112DH2P is the C2 pump machine in the Ironman Duplex Series: two independent 7.5 HP motor and pump assemblies on a single 120 gallon horizontal tank. Each side runs a C2 two-stage cast iron pump rated 26 CFM, for 52 CFM combined at a maximum 175 PSI. Because the two assemblies are separate, one can come down for service while the other keeps air on the line, which is the reason most shops step up to a duplex rather than buying one larger simplex machine. Choose 230V single-phase (ABC7-2112DH2P) or 230V three-phase (ABC7-2312DH2P).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC7-2112DH2P (230V 1-phase) \/ ABC7-2312DH2P (230V 3-phase)\u003c\/li\u003e\n\u003cli\u003ePower: 15 HP total (2 x 7.5 HP)\u003c\/li\u003e\n\u003cli\u003ePumps: two C2 two-stage pumps, full cast iron construction\u003c\/li\u003e\n\u003cli\u003eAir delivery: 52 CFM combined (26 CFM per pump)\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 230\/3\/60\u003c\/li\u003e\n\u003cli\u003eDrive: belt drive, two independent motor and pump assemblies\u003c\/li\u003e\n\u003cli\u003eAlternating control to decrease downtime\u003c\/li\u003e\n\u003cli\u003eDual control to increase output\u003c\/li\u003e\n\u003cli\u003eFully programmable control panel settings\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat the duplex control actually does\u003c\/h3\u003e\u003cp\u003eTwo pumps on one tank only pay for themselves if the controller uses them properly, and the Ironman Duplex panel is built for that. Alternating control rotates which side leads, so run hours and service intervals are shared instead of one pump carrying the shop while the other sits. Dual control brings both sides on together when demand climbs, for the full 52 CFM. Between the two, each pump runs cooler, rests longer and reaches an oil change later than a single pump doing the same total work, and the panel settings are fully programmable so the changeover matches how your floor actually draws air. The practical benefit is the one that matters on a production day: a belt change, an oil service or a failed pump takes half the capacity offline, not all of it.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eAcross the Ironman duplex machines on the 120 gallon horizontal tank, the pump choice sets the airflow. The \u003ca href=\"\/products\/abac-abc5-duplex-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e10 HP ABC5-21120HD\u003c\/a\u003e pairs two C1 pumps for 32 CFM, and the \u003ca href=\"\/products\/abac-abc7-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e15 HP ABC7-21120HD\u003c\/a\u003e pairs two C1 pumps for 42 CFM. This machine keeps the same 15 HP total and the same tank but steps the pumps up to C2 for 52 CFM, which is the cheapest way to add 10 CFM without moving up a motor size or a service panel. Above it, the \u003ca href=\"\/products\/abac-abc10-duplex-20-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e20 HP ABC10-23120HD\u003c\/a\u003e reaches 64 CFM, and the \u003ca href=\"\/products\/abac-abc10-2312dhp-20-hp-120-gallon-horizontal-ironman-duplex-air-compressor\"\u003eABC10-2312DHP\u003c\/a\u003e is the C2 version of that pair. If redundancy is not the point, the single pump \u003ca href=\"\/products\/abac-abc7-2180v2p-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003e7.5 HP ABC7-2180V2P\u003c\/a\u003e uses the same C2 pump on an 80 gallon vertical tank in a far smaller footprint. Size on the CFM your tools actually draw, then confirm your panel can carry the phase you pick.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC builds the Ironman Duplex Series for professional work that needs a consistent air supply: metal and wood shops, auto body and repair shops, tire inflation, hammering, grinding, fastening, orbital sanding and equipment operation. In practice that means production floors, multi-bay service centers, fabrication and welding bays, and fleet maintenance operations where several tools draw at once and a compressor going down stops the whole shop. A duplex also suits a shop with a wide gap between its light and heavy demand: one side carries the quiet hours and both run when the floor is full, so neither pump spends the day at full duty.\u003c\/p\u003e\u003ch3\u003ePower, installation and air treatment\u003c\/h3\u003e\u003cp\u003eTake three-phase power if the panel has it, since three-phase motors start easier and run cooler on a compressor that cycles all day. Both sides can run together, so size the circuit for the pair even though the control normally alternates them, and leave clearance around the flywheels for cooling air and service access. A 120 gallon receiver collects real water, so plan the drain. A two-stage piston running to 175 PSI also puts warm, wet air into the line, and that moisture carries down to whatever is on the end of it. If the air reaches paint, plasma, pneumatic controls or anything that rusts, pair this compressor with a refrigerated dryer rated at or above its 52 CFM output, such as the \u003ca href=\"\/products\/abac-cool-65-refrigerated-air-dryer-115v\"\u003eABAC COOL 65\u003c\/a\u003e or, for margin on a hot shop floor, the \u003ca href=\"\/products\/abac-cool-75-refrigerated-air-dryer-115v\"\u003eCOOL 75\u003c\/a\u003e, plus a filter regulator at the drop. Browse the rest of our \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the Atlas Copco group. The C2 build steps up from the 42 CFM C1 duplex while still spreading run time across two pumps, which keeps each one cooler and shortens recovery under heavy demand. See the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":67579199553811,"sku":"2020141043","price":8921.0,"currency_code":"USD","in_stock":true},{"title":"230V 3-Phase","offer_id":67579199586579,"sku":"2020141044","price":8752.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc7-2112dh2p-duplex-120-gallon-horizontal-ironman-air-compressor.png?v=1791414430"},{"product_id":"abac-abc10-2312hp-10-hp-120-gallon-horizontal-ironman-air-compressor","title":"ABAC ABC10-2312HP 10 HP Two-Stage Ironman Air Compressor - 120 Gallon Horizontal, 175 PSI, 32 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC10-2312HP pairs a 10 HP motor with the C2 two-stage cast iron pump on a 120 gallon horizontal ASME tank, delivering 32 CFM at a maximum 175 PSI. The horizontal layout sits low and long, 74 in end to end but only 50 in tall, which suits shops that would rather run the compressor along a wall or under a mezzanine than give up vertical footprint. This is a three-phase machine only. Choose 230V three-phase (ABC10-2312HP) or 460V three-phase (ABC10-43120HP).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC10-2312HP \/ ABC10-43120HP\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, belt drive\u003c\/li\u003e\n\u003cli\u003ePump: C2 two-stage, fully cast iron construction\u003c\/li\u003e\n\u003cli\u003eAir delivery: 32 CFM at maximum pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/3\/60 or 460\/3\/60\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 27 x 74 x 50 in\u003c\/li\u003e\n\u003cli\u003eWeight: 728 lbs\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard, discharge valve, magnetic starter\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a two-stage cast iron pump\u003c\/h3\u003e\u003cp\u003eThe C2 is the cast iron pump ABAC builds the Ironman range around, and the second stage is what carries the air up to 175 PSI rather than the 125 to 135 PSI a shop is used to seeing from a lighter single-stage machine. Compressing in two steps with cooling in between means lower discharge temperatures per stage, and cast iron cylinders shed that heat and wear slowly instead of glazing. The practical result is a pump rated for heavy daily duty that can be serviced and rebuilt rather than replaced, which is the difference between a shop compressor and a consumable one.\u003c\/p\u003e\u003ch3\u003eWhat the 120 gallon horizontal tank changes\u003c\/h3\u003e\u003cp\u003eStorage is what keeps line pressure flat when several tools draw at once. A 120 gallon receiver gives the motor far fewer starts than an 80 gallon build on the same 32 CFM pump, and fewer starts means less heat, less contactor wear and steadier pressure at the drop. The horizontal layout spends that capacity on length instead of height: 74 in of wall and 50 in of clearance, against the 74 in of height a 120 gallon vertical needs. Plan for 728 lbs on the floor and check your door and ceiling clearance before delivery day.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eSame pump, same 32 CFM, different footprint. The \u003ca href=\"\/products\/abac-abc10-2312vp-10-hp-120-gallon-vertical-ironman-air-compressor\"\u003eABC10-2312VP vertical build\u003c\/a\u003e stands 74 in tall on a 30 x 41 in base and weighs 765 lbs, trading floor space for height. This horizontal unit runs 74 in long and only 50 in tall at 728 lbs, which is the one to pick under a mezzanine or a low ceiling. If you want the automatic tank drain, low oil level shut off and belt guard aftercooler fitted at the factory, the \u003ca href=\"\/products\/abac-abc10-ff-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC10-23120HFF full feature horizontal\u003c\/a\u003e is the same machine with the protection package already on it. If 32 CFM is already marginal, the \u003ca href=\"\/products\/abac-abc10-2312dhp-20-hp-120-gallon-horizontal-ironman-duplex-air-compressor\"\u003eABC10-2312DHP duplex\u003c\/a\u003e puts two 10 HP pumps on one 120 gallon tank for 64 CFM and lets you service one side while the other keeps air on the line.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction shops, fabrication and welding bays, truck and fleet maintenance, tire shops running multiple lifts, and any operation where several air tools or a plasma cutter draw at the same time and the compressor needs to hold pressure through the shift rather than recover between jobs. ABAC rates the Ironman range for professional heavy duty work: hammering, grinding, orbital sanding, fastening, spraying, tire inflation and general equipment operation. At 32 CFM it will carry a pair of busy sanders or ratchets, a plasma cutter, or a blast cabinet in short sessions.\u003c\/p\u003e\u003ch3\u003eInstallation and air treatment\u003c\/h3\u003e\u003cp\u003ePlan on a three-phase circuit sized to the motor nameplate and a disconnect within sight of the machine; there is no single-phase option in this frame size. Leave clearance around the flywheel and belt guard for cooling air and for belt service, and pipe the discharge with a flexible connector so vibration does not load the shop line. Oil, the air filter element and the belts are the routine service items. Where the air feeds paint, plasma or pneumatic controls, add a refrigerated dryer rated above the compressor's 32 CFM: the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eABAC COOL 50\u003c\/a\u003e is rated 50 CFM and runs on standard 115V single-phase power, so it sits beside the compressor without new wiring. A \u003ca href=\"\/collections\/coalescing-air-filters\"\u003ecoalescing filter\u003c\/a\u003e downstream protects finishing work, and a \u003ca href=\"\/collections\/condensate-drains\"\u003econdensate drain\u003c\/a\u003e keeps the water the tank collects off your floor.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the Atlas Copco group. The 120 gallon reservoir cuts motor starts and holds a steadier line pressure than an 80 gallon build, while the horizontal tank keeps overall height down where ceiling clearance is tight. See the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e, the full range of \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e, or browse all \u003ca href=\"\/collections\/air-compressors\"\u003eair compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 3-Phase","offer_id":67616727335187,"sku":"2020141030","price":4722.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":67616727367955,"sku":"2020141040","price":4722.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc10-2312hp-120-gallon-horizontal-ironman-air-compressor.png?v=1791439701"},{"product_id":"abac-abc5-2112dhp-10-hp-120-gallon-horizontal-ironman-duplex-air-compressor","title":"ABAC ABC5-2112DHP 10 HP Ironman Duplex Air Compressor - 120 Gallon Horizontal, 175 PSI, 32 CFM C1 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC5-2112DHP Ironman duplex mounts two independent 5 HP motor and pump assemblies on a single 120 gallon horizontal ASME tank. Each side runs a C1 two-stage cast iron pump rated 16 CFM, for 32 CFM combined at a maximum 175 PSI. Because the two assemblies are separate, one can come down for service while the other keeps air on the line, which is the reason most shops step up to a duplex in the first place. It runs on 230V single-phase power.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: ABC5-2112DHP\u003c\/li\u003e\n\u003cli\u003eWarthog part number: 2020141042\u003c\/li\u003e\n\u003cli\u003ePower: 10 HP total (2 x 5 HP)\u003c\/li\u003e\n\u003cli\u003ePumps: two C1 two-stage pumps, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 32 CFM combined (16 CFM per pump)\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60\u003c\/li\u003e\n\u003cli\u003eAlternating control, so the lead pump rotates and run time is shared\u003c\/li\u003e\n\u003cli\u003eFully programmable control panel\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guards\u003c\/li\u003e\n\u003cli\u003eMagnetic starter and discharge valve standard\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a duplex on single-phase power\u003c\/h3\u003e\u003cp\u003eA single 10 HP piston compressor normally calls for three-phase service. Splitting the same output across two 5 HP assemblies keeps each motor within what a 230V single-phase supply can carry, which is what puts 10 HP of output within reach of a shop on utility single-phase. Both pumps feed the same receiver, and either side can be isolated for a belt or valve change without shutting the floor down.\u003c\/p\u003e\u003ch3\u003eWhat alternating control actually does\u003c\/h3\u003e\u003cp\u003eABAC builds the Ironman Duplex range around alternating control, which rotates the lead pump so wear is spread across both assemblies instead of accumulating on one. Through a quiet morning one pump carries the load on its own and the second never starts, so neither side racks up hours it does not need. When every bay is working, both run together and the pair delivers the full 32 CFM. The fully programmable control panel is what sets those parameters, so the changeover point and the cut in and cut out pressures are tuned to how your shop actually draws air rather than left at a factory default.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the Ironman duplex range the pumps scale with the output. The \u003ca href=\"\/products\/abac-abc7-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC7 15 HP duplex\u003c\/a\u003e pairs two 7.5 HP C1 pumps for 42 CFM, the \u003ca href=\"\/products\/abac-abc7-v2-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e15 HP ABC7-2112DH2P\u003c\/a\u003e reaches 52 CFM on C2 pumps, and the \u003ca href=\"\/products\/abac-abc10-2312dhp-20-hp-120-gallon-horizontal-ironman-duplex-air-compressor\"\u003eABC10-2312DHP 20 HP duplex\u003c\/a\u003e steps up to two C2 pumps for 64 CFM on the same 120 gallon horizontal platform. If your service is three-phase and redundancy is not the point, the single pump \u003ca href=\"\/products\/abac-abc10-2312hp-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC10-2312HP\u003c\/a\u003e reaches the same 32 CFM from one C2 pump on the same tank. Size on the CFM your tools actually draw, then confirm the incoming service matches.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC rates the Ironman Duplex range for extensive use, the consistent supply that metal and wood workshops and auto body and repair shops need, and lists agriculture and farm, food and beverage and general industrial work among its applications. On a single-phase floor that means service garages, body shops, small production and fabrication cells, and fleet maintenance bays that need air all day and cannot afford to lose the whole compressor to one failed pump. The 120 gallon horizontal receiver keeps the pumps from short cycling between tool triggers and gives impact wrenches and sanders a reserve to draw on.\u003c\/p\u003e\u003ch3\u003ePlanning the installation\u003c\/h3\u003e\u003cp\u003eTreat this as two compressors sharing one receiver. Each side runs on its own 230V single-phase circuit sized to its motor nameplate, so size the service to the pair rather than to a single 5 HP machine. Leave clearance down both sides for cooling airflow and for belt guard and pump access, since service on one side happens while the other is still running. Drain the receiver on a schedule or fit an automatic drain, because condensate left standing is what ends a tank's life early.\u003c\/p\u003e\u003ch3\u003eAir treatment\u003c\/h3\u003e\u003cp\u003eA piston compressor delivers saturated air, so spray finishing, plasma cutting, and air logic all want drying downstream. At 32 CFM combined the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35\u003c\/a\u003e covers both pumps running together with a little headroom, and it runs on a 115V outlet rather than needing its own three-phase feed. See the rest of our \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e if the line feeds more than this machine.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the \u003ca href=\"\/collections\/atlas-copco\"\u003eAtlas Copco\u003c\/a\u003e group. Standard features across the two-stage Ironman series include a fully enclosed belt guard, fully cast iron pump design, ASME tank and safety valves, a discharge valve, and a magnetic starter. Splitting demand across two C1 pumps keeps each one running cooler and cuts duty cycle on both, which is what extends pump life in shops where air is drawn all day long. Browse the full range of \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":67617266303251,"sku":"2020141042","price":7862.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc5-2112dhp-duplex-120-gallon-horizontal-ironman-air-compressor.png?v=1791270343"},{"product_id":"abac-abc10-2312dhp-20-hp-120-gallon-horizontal-ironman-duplex-air-compressor","title":"ABAC ABC10-2312DHP 20 HP Ironman Duplex Air Compressor - 120 Gallon Horizontal, 175 PSI, 64 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC10-2312DHP Ironman duplex mounts two independent 10 HP motor and pump assemblies on a single 120 gallon horizontal tank. Each side runs a C2 two-stage cast iron pump rated 32 CFM, for 64 CFM combined at a maximum 175 PSI. Because the two assemblies are separate, one can come down for service while the other keeps air on the line, which is the reason most shops step up to a duplex in the first place. Choose 230V three-phase (ABC10-2312DHP) or 460V three-phase (ABC10-4312DHP).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC10-2312DHP (230V) \/ ABC10-4312DHP (460V)\u003c\/li\u003e\n\u003cli\u003eWarthog part numbers: 2020141041 (230V) and 2020141045 (460V)\u003c\/li\u003e\n\u003cli\u003ePower: 20 HP total (2 x 10 HP)\u003c\/li\u003e\n\u003cli\u003ePumps: two C2 two-stage pumps, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 64 CFM combined (32 CFM per pump)\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/3\/60 or 460\/3\/60\u003c\/li\u003e\n\u003cli\u003eAlternating control, so the lead pump rotates and run time is shared\u003c\/li\u003e\n\u003cli\u003eFully programmable control panel\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy two pumps instead of one larger machine\u003c\/h3\u003e\u003cp\u003eABAC builds the Ironman Duplex range around alternating control, which rotates the lead pump so wear is spread across both assemblies rather than accumulating on one. That has two practical effects. Through a quiet morning one pump carries the load on its own and the second never starts, so neither assembly racks up hours it does not need. When every bay is working, both run together and the pair delivers the full 64 CFM. A single 20 HP machine covering the same demand swings between loaded and unloaded all day, and when it comes down for a belt or a pressure switch the shop is out of air. Here the second side holds the line up while the first is open.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eAcross the Ironman duplex range the pump size sets the airflow and the tank sets how long the pumps rest between draws. The \u003ca href=\"\/products\/abac-abc5-2112dhp-10-hp-120-gallon-horizontal-ironman-duplex-air-compressor\"\u003e10 HP ABC5-2112DHP\u003c\/a\u003e pairs two C1 pumps for 32 CFM on the same 120 gallon horizontal tank, and the \u003ca href=\"\/products\/abac-abc7-v2-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e15 HP ABC7-2112DH2P\u003c\/a\u003e reaches 52 CFM. The \u003ca href=\"\/products\/abac-abc10-2320dhp-20-hp-200-gallon-horizontal-ironman-duplex-air-compressor\"\u003eABC10-2320DHP\u003c\/a\u003e is this same 64 CFM pair on a 200 gallon receiver, worth the extra floor space where draws are heavy and intermittent. If redundancy is not the point and 32 CFM is enough, the single pump \u003ca href=\"\/products\/abac-abc10-2312hp-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC10-2312HP\u003c\/a\u003e uses the same C2 pump and the same 120 gallon tank.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC rates the Ironman Duplex range for extensive use, the consistent supply that metal and wood workshops and auto body and repair shops need, and lists agriculture and farm, food and beverage and general industrial work among its applications. On a shop floor that means production and fabrication cells, multi bay service centers, welding bays, and fleet maintenance operations where several air tools draw at once and a compressor going down stops everyone. Alternating control also suits a plant whose demand swings widely through the day: one pump carries the quiet hours and the second cuts in when every bay is working, instead of a single large machine short cycling through both.\u003c\/p\u003e\u003ch3\u003ePlanning the installation\u003c\/h3\u003e\u003cp\u003eTreat this as two compressors sharing one receiver. Each side runs on its own three-phase circuit sized to its motor nameplate, so size the service to the pair rather than to a single 10 HP machine, and confirm the supply voltage before ordering, because the 230V and 460V builds are separate units rather than a field conversion. Leave clearance down both sides for cooling airflow and for belt guard and pump access, since service on one side happens while the other is still running. Drain the receiver on a schedule or fit an automatic drain, because condensate left standing is what ends a tank's life early. Two-stage air at 175 PSI carries a shop floor's worth of moisture, so plan a refrigerated dryer downstream of the tank: at 64 CFM combined the 100 CFM \u003ca href=\"\/products\/abac-cool-100-refrigerated-air-dryer-230v\"\u003eABAC COOL 100\u003c\/a\u003e covers the pair with headroom for both pumps running together.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the Atlas Copco group. A duplex pair delivers the output of a larger single machine while spreading run time across two pumps, which keeps each one cooler and shortens recovery under heavy demand. See the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our full range of \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 3-Phase","offer_id":67617411825939,"sku":"2020141041","price":9023.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":67617411858707,"sku":"2020141045","price":9469.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc10-2312dhp-duplex-120-gallon-horizontal-ironman-air-compressor.png?v=1791273903"},{"product_id":"abac-abc10-2320dhp-20-hp-200-gallon-horizontal-ironman-duplex-air-compressor","title":"ABAC ABC10-2320DHP 20 HP Ironman Duplex Air Compressor - 200 Gallon Horizontal, 175 PSI, 64 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC10-2320DHP Ironman duplex puts two independent 10 HP motor and pump assemblies on a single 200 gallon horizontal tank. Each side runs a C2 two-stage cast iron pump rated 32 CFM, for 64 CFM combined at a maximum 175 PSI. The large receiver gives the pair more stored air to draw against, so the pumps cycle less under a swinging load. Because the two assemblies are separate, one can come down for service while the other keeps air on the line, which is the reason most shops step up to a duplex in the first place. Choose 230V three-phase (ABC10-2320DHP) or 460V three-phase (ABC10-4320DHP).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC10-2320DHP (part number 2020141039) and ABC10-4320DHP (part number 2020141038)\u003c\/li\u003e\n\u003cli\u003ePower: 20 HP total (2 x 10 HP)\u003c\/li\u003e\n\u003cli\u003ePumps: two C2 two-stage pumps, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 64 CFM combined (32 CFM per pump)\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 200 gallon horizontal\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/3\/60 or 460\/3\/60\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guards\u003c\/li\u003e\n\u003cli\u003eAlternating control and a fully programmable control panel, specified by ABAC across the Ironman Duplex range\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a duplex instead of one larger compressor\u003c\/h3\u003e\u003cp\u003eA duplex splits the same output across two smaller pumps. Under light demand the two sides alternate, so each pump runs roughly half the hours and stays cooler, and ABAC builds alternating control into the Ironman Duplex range specifically to rotate the lead pump and spread wear instead of loading one machine. Under peak draw both sides run together and the full 64 CFM is on tap. If a motor, a pump or a starter fails, the remaining side still makes 32 CFM, which usually keeps a floor working until the part arrives instead of shutting it down. The trade is two sets of service items rather than one: two oil changes, two belt sets, two intake filters.\u003c\/p\u003e\u003ch3\u003eWhat the 200 gallon receiver buys you\u003c\/h3\u003e\u003cp\u003eTank volume does not change how much air the pumps make. It changes how the machine behaves between draws. A larger receiver holds more compressed air in reserve, so a burst of demand comes out of storage first and line pressure holds while the pumps catch up. The pumps then start less often and run longer when they do start, which is easier on motors, contactors and belts than short cycling. That matters most where the load swings: a blast cabinet, a plasma table, or four or five bays that all reach for air at the same time. The 200 gallon tank is the reason to choose this machine over the otherwise identical 120 gallon version, and the cost is floor space.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the Ironman duplex range the pumps and the receiver scale separately. The \u003ca href=\"\/products\/abac-abc10-2312dhp-20-hp-120-gallon-horizontal-ironman-duplex-air-compressor\"\u003eABC10-2312DHP\u003c\/a\u003e is the same 20 HP pair at the same 64 CFM on a 120 gallon tank, so it takes less floor space and stores less air between cycles. Below that, the \u003ca href=\"\/products\/abac-abc7-v2-duplex-15-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC7-2112DH2P\u003c\/a\u003e delivers 52 CFM from two 7.5 HP C2 pumps and the \u003ca href=\"\/products\/abac-abc5-2112dhp-10-hp-120-gallon-horizontal-ironman-duplex-air-compressor\"\u003eABC5-2112DHP\u003c\/a\u003e delivers 32 CFM from two 5 HP C1 pumps, both on 120 gallon horizontal tanks. Every machine in the range tops out at the same 175 PSI, so size on CFM first and on receiver volume second. If redundancy is not the point and 32 CFM covers the work, a single pump machine such as the \u003ca href=\"\/products\/abac-abc10-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC10-23120H\u003c\/a\u003e uses the same C2 pump at a lower installed cost. Above this machine the next step is a rotary screw rated for 100 percent duty rather than a larger piston compressor.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC positions the Ironman Duplex range for extensive use, meaning professional work that needs a consistent supply of compressed air, and names metal and wood workshops and auto body and repair shops as typical settings, along with agriculture and farm, food and beverage and general industrial duty. On the floor that looks like production shops, multi bay service and collision centers, fabrication and welding bays, and fleet maintenance operations running several air tools at once, where a compressor going down stops everything. Alternating control also suits a plant whose demand swings through the day: one pump carries the quiet hours and the second cuts in when every bay is working, instead of a single large machine short cycling through both.\u003c\/p\u003e\u003ch3\u003ePower and installation\u003c\/h3\u003e\u003cp\u003eBoth versions are three-phase only, so confirm what the panel actually supplies before ordering and size the feeder to the combined nameplate of the two motors rather than to one. Leave working room at both ends of the tank for belt guard access and for the drains, and plan a timed or automatic drain, because a 200 gallon receiver collects a great deal of condensate and a manual drain that nobody pulls is how tanks rust from the inside. Keep the room ventilated: two pumps at full load put real heat into a space, and intake air that is hot or dusty shortens the life of both sides at once.\u003c\/p\u003e\u003ch3\u003eAir treatment\u003c\/h3\u003e\u003cp\u003eA two-stage piston compressor this size puts a lot of water into the line. Size the dryer above the compressor output: at 64 CFM the \u003ca href=\"\/products\/abac-cool-100-refrigerated-air-dryer-230v\"\u003eABAC COOL 100\u003c\/a\u003e refrigerated dryer, rated 100 CFM, leaves headroom for a hot day and a long duty cycle. Put the dryer downstream of the receiver so the tank drops out the easy water first, and add a filter regulator ahead of anything that sprays, meters or holds a tolerance. See the full range of \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the Atlas Copco group. A duplex pair delivers the output of a larger single machine while spreading run time across two pumps, which keeps each one cooler and shortens recovery under heavy demand. See our wider selection of \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and all \u003ca href=\"\/collections\/air-compressors\"\u003eair compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 3-Phase","offer_id":67617793376531,"sku":"2020141039","price":10722.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":67617793409299,"sku":"2020141038","price":11170.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc10-2320dhp-duplex-200-gallon-horizontal-ironman-air-compressor.png?v=1791277827"}],"url":"https:\/\/aircompressorstore.com\/collections\/abac-horizontal-tank-air-compressors.oembed","provider":"Warthog Air Compressor Store","version":"1.0","type":"link"}