{"title":"ABAC Full Feature Air Compressors","description":"\u003cp\u003eABAC Full Feature (FF) air compressors are the protected builds of the stationary piston range. Where a standard machine gives you the pump, motor and ASME receiver, the Full Feature package adds the parts that keep the compressor looking after itself between shifts: an automatic tank drain so condensate never sits in the receiver, an aftercooler that drops discharge temperature and knocks moisture out before it reaches your air lines, and low oil and high temperature protection that shuts the machine down before damage happens rather than after.\u003c\/p\u003e\u003cp\u003eThat matters most where a compressor runs unattended or where nobody is checking a drain valve every morning. Body shops, production cells, machine shops and any installation where the compressor sits in a back room are the usual buyers. The Full Feature premium is small next to a seized pump or a tank that rusted from the inside out.\u003c\/p\u003e\u003ch3\u003eWhat is in this collection\u003c\/h3\u003e\u003cp\u003eBoth ABAC pump platforms are represented. The Hybrid Pro FF machines use the aluminum and cast iron T39 or PAT 49 pump and run 14.6 to 22.2 CFM at 175 PSI on 80 gallon vertical and horizontal tanks. The \u003ca href=\"\/collections\/abac-ironman-air-compressors\"\u003eIronman\u003c\/a\u003e FF machines use the fully cast iron C1 and C2 pumps and run 16 to 32 CFM at 175 PSI on 80 and 120 gallon tanks, in single phase 230V through three phase 575V. Every machine here is two-stage and belt driven on an ASME receiver.\u003c\/p\u003e\u003ch3\u003eChoosing a Full Feature machine\u003c\/h3\u003e\u003cp\u003eSize on CFM first, against the air tools that will run at the same time, then decide pump construction. The hybrid pump is lighter and the better value where duty cycles are moderate; the cast iron Ironman pump sheds heat better and is what to buy if the compressor runs most of the day under load. Confirm the voltage and phase your panel actually supplies before ordering, because the FF models span 230V single phase to 575V three phase.\u003c\/p\u003e\u003cp\u003eSee the full \u003ca href=\"\/collections\/abac-piston-air-compressors\"\u003eABAC piston air compressor\u003c\/a\u003e range, the rest of the \u003ca href=\"\/collections\/abac-air-compressors\"\u003eABAC lineup\u003c\/a\u003e, or add a \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e downstream when the work calls for genuinely dry air.\u003c\/p\u003e","products":[{"product_id":"abac-ab5-2180v4ff-5-hp-80-gallon-vertical-premium-air-compressor","title":"ABAC AB5-2180V4FF 5 HP Two-Stage Air Compressor - 80 Gallon Vertical Premium, 175 PSI, 14.6 CFM, 230V Single-Phase","description":"\u003cp\u003eThe ABAC AB5-2180V4FF is the Full Feature build of the 80 gallon vertical AB5 platform. The two-stage PAT 49 pump pairs an aluminum head and aftercooler with cast iron cylinders, so heat and moisture are pulled out of the air before it reaches the tank, and the FF specification adds a pressure-actuated automatic tank drain and a low oil level switch. It delivers 14.6 CFM at a maximum 175 PSI on 230V single-phase power.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AB5-2180V4FF (part number 8090304547)\u003c\/li\u003e\n\u003cli\u003eFull Feature additions: pressure-actuated automatic tank drain, low oil level switch\u003c\/li\u003e\n\u003cli\u003eMotor: 5 HP, 230V \/ 1-phase \/ 60 Hz, 184T frame\u003c\/li\u003e\n\u003cli\u003ePump: PAT 49 two-stage, aluminum with cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 14.6 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 80 gallon vertical, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eAluminum head and aftercooler for heat dissipation and moisture removal\u003c\/li\u003e\n\u003cli\u003eOversized flywheel for added pump airflow and cooling efficiency\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat the Full Feature spec buys you\u003c\/h3\u003e\u003cp\u003eTwo of the jobs on a compressor's daily checklist are draining condensate out of the tank and confirming the crankcase still has oil in it. Both get skipped in a busy shop, and both are expensive when they are. Water left standing in an 80 gallon receiver rusts it from the inside and carries moisture down the line into air tools and spray work. Running a two-stage pump low on oil ends it. The FF build automates the first with a pressure-actuated drain that blows the tank down on its own, and guards the second with a low oil level switch that stops the machine rather than letting it run dry. That is the whole difference between this unit and the standard AB5-2180V4, and it is the reason to pay for it anywhere nobody is specifically assigned to the compressor.\u003c\/p\u003e\u003ch3\u003eStandard features\u003c\/h3\u003e\u003cp\u003eEvery machine in ABAC's 2-Stage Hybrid Pro range shares the same core build: cast iron cylinders under an aluminum head, an aluminum aftercooler, an ASME coded tank with safety valves, a fully enclosed belt guard that protects the operator and routes cooling air across the pump, and start and stop pressure switch control. ABAC calls the pump hybrid because the aluminum manages heat while the cast iron cylinders take the wear, and the inner cooling design is what holds operating temperature down through a long duty cycle. The units are assembled in the USA and carry a 2 year full warranty.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eThe three 80 gallon AB5 models all deliver the same 14.6 CFM at 175 PSI, so the decision is about what comes fitted. The \u003ca href=\"\/products\/abac-ab5-2180v4ns-5-hp-80-gallon-vertical-two-stage-air-compressor\"\u003eAB5-2180V4NS\u003c\/a\u003e ships without a magnetic starter, the \u003ca href=\"\/products\/abac-ab5-2180v4-5-hp-80-gallon-vertical-two-stage-air-compressor\"\u003eAB5-2180V4\u003c\/a\u003e includes one, and this FF build is specified with the automatic tank drain and the low oil level switch. Where floor space matters more than stored air, the \u003ca href=\"\/products\/abac-ab5-2160v4-5-hp-60-gallon-vertical-two-stage-air-compressor\"\u003e60 gallon AB5-2160V4\u003c\/a\u003e runs the same pump on a smaller footprint. If the shop needs more air rather than more automation, the \u003ca href=\"\/products\/abac-ab5-2180vpff-5-hp-80-gallon-vertical-premium-air-compressor\"\u003eAB5-2180VPFF\u003c\/a\u003e is the same 5 HP in Full Feature trim with the T39 pump for 16.6 CFM, and the \u003ca href=\"\/products\/abac-ab7-ff-7-5-hp-80-gallon-vertical-premium-air-compressor\"\u003e7.5 HP AB7-2180VFF\u003c\/a\u003e steps up to 22.2 CFM on the same 80 gallon vertical tank. Where noise is the constraint instead, the enclosed \u003ca href=\"\/products\/abac-ab5-2180vqp-5-hp-quiet-power-80-gallon-air-compressor\"\u003eAB5-2180VQP Quiet Power\u003c\/a\u003e delivers 16.6 CFM at 66 dBA.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC rates the Hybrid Pro range for air and water spraying, impact wrenching, screwing, hammering, grinding, fastening, orbital sanding, equipment operation and tire inflation. In practice that means body shops, woodworking shops, farm and agricultural buildings, and general maintenance bays where the compressor is called on through most of the shift rather than in short bursts. At 14.6 CFM it will keep one operator going on sanding or spray work, or feed several intermittent tools across a bay, and the 80 gallon receiver carries the surge so the pump is not restarting on every trigger pull. The vertical tank puts that capacity against a wall instead of across the floor, which is usually what decides between this and a horizontal machine.\u003c\/p\u003e\u003cp\u003eTwo-stage compressors push warm, wet air into the line, so most shops add a refrigerated dryer rated above the compressor's 14.6 CFM output, such as the \u003ca href=\"\/products\/abac-cool-25-refrigerated-air-dryer-115v\"\u003eABAC COOL 25\u003c\/a\u003e. Browse the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/air-dryers\"\u003ecompressed air dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"Default Title","offer_id":54557402300691,"sku":"8090304547","price":2746.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-ab5-2180v4ff-80-gallon-premium-air-compressor.png?v=1786375951"},{"product_id":"abac-ab5-2180vpff-5-hp-80-gallon-vertical-premium-air-compressor","title":"ABAC AB5-2180VPFF 5 HP Two-Stage Air Compressor - 80 Gallon Vertical Premium, 175 PSI, 16.6 CFM T39 Pump","description":"\u003cp\u003eThe ABAC AB5 VPFF pairs the highest output 5 HP pump in the 2-Stage Hybrid Pro range with ABAC's Full Feature package. The belt driven T39 two-stage pump moves 16.6 CFM at a maximum 175 PSI, a full two CFM above the standard 5 HP V4 builds, and the FF specification adds the protection that lets the machine run without somebody checking it daily. All three voltage builds ride on the same 80 gallon vertical ASME tank and weigh the same 398 lbs: 230V single-phase (AB5-2180VPFF), 230V three-phase (AB5-2380VPFF), or 460V three-phase (AB5-4380VPFF).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AB5-2180VPFF (230V single-phase), AB5-2380VPFF (230V three-phase), AB5-4380VPFF (460V three-phase)\u003c\/li\u003e\n\u003cli\u003eWarthog part numbers: 8090304315, 8090304349, 8090304364 (ABAC part numbers 2021119417, 2021119419, 2021119421)\u003c\/li\u003e\n\u003cli\u003eMotor: 5 HP, 60 Hz\u003c\/li\u003e\n\u003cli\u003ePump: T39 two-stage hybrid, aluminum with cast iron cylinders and inner cooling technology\u003c\/li\u003e\n\u003cli\u003eAir delivery: 16.6 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 80 gallon vertical, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eFull Feature additions: automatic tank drain and low oil level automatic shut off\u003c\/li\u003e\n\u003cli\u003eAluminum heads and aftercoolers for heat dissipation and moisture removal\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eStart\/stop pressure switch control\u003c\/li\u003e\n\u003cli\u003eWeight: 398 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 25 x 34 x 75 in\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat the FF package adds\u003c\/h3\u003e\u003cp\u003eFF is ABAC's Full Feature designation, and ABAC defines a Full Feature build as the standard machine plus an automatic tank drain and a low oil level automatic shut off. Those two additions cover the maintenance steps a busy shop skips first. Condensate collects in an 80 gallon receiver every day a two-stage pump runs, and a tank nobody drains rusts from the inside and pushes water down the line into tools and finish work. A low oil level shut off stops the pump before it runs dry instead of after. If the compressor lives in a mechanical room and nobody is assigned to it, that is what the FF premium buys. If somebody opens the drain and checks the sight glass every morning, the standard VP build does the same work for less.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eTwo decisions separate the 80 gallon 5 HP builds, and the first is the pump. The \u003ca href=\"\/products\/abac-ab5-2180v4ff-5-hp-80-gallon-vertical-premium-air-compressor\"\u003eAB5-2180V4FF\u003c\/a\u003e runs the PAT 49 pump for 14.6 CFM; the VPFF steps up to the T39 for 16.6 CFM on the same tank at the same 175 PSI, which is the margin that keeps a second air tool from pulling the line down. The second decision is the Full Feature package itself. The \u003ca href=\"\/products\/abac-ab5-2180vp-5-hp-80-gallon-vertical-two-stage-air-compressor\"\u003eAB5-2180VP\u003c\/a\u003e is the same T39 machine without the automatic drain and the low oil level shut off, so it suits a shop where somebody checks the compressor daily, and the VPFF suits one where nobody is assigned to it. If the tool list already outruns 16.6 CFM, the \u003ca href=\"\/products\/abac-ab7-ff-7-5-hp-80-gallon-vertical-premium-air-compressor\"\u003e7.5 HP AB7-2180VFF\u003c\/a\u003e delivers 22.2 CFM on the identical 80 gallon vertical footprint. If noise is the deciding factor, the \u003ca href=\"\/products\/abac-ab5-2180vqp-5-hp-quiet-power-80-gallon-air-compressor\"\u003eAB5-2180VQP\u003c\/a\u003e Quiet Power delivers the same 16.6 CFM at 66 dBA, though it carries 527 lbs in a 39 x 24 x 80 in cabinet.\u003c\/p\u003e\u003ch3\u003eChoosing a voltage\u003c\/h3\u003e\u003cp\u003eAll three builds deliver the same 16.6 CFM at 175 PSI, weigh the same 398 lbs and share the same 25 x 34 x 75 in footprint, so the decision comes down to what the panel offers. Pick 230V single-phase if the shop runs on common single-phase service. Where three-phase exists, the 230V or 460V three-phase build is the better long term choice, because a three-phase motor starts under less stress and runs cooler at the same load, and that matters on a machine that starts against a full 175 PSI tank several times an hour. Whichever build you pick, run it on its own circuit sized to the motor nameplate and have an electrician confirm the service before delivery.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC lists the Hybrid Pro range for air and water spraying, impact wrenching, hammering, grinding, fastening, tire inflation and general equipment operation. In practice that means collision centers, dealership service departments, production fabrication and woodworking shops, farm buildings, and busy maintenance bays. At 16.6 CFM the machine will hold up a DA sander or a die grinder continuously, or a pair of impact wrenches used intermittently, and the 80 gallon vertical receiver absorbs the surges so the pump is not restarting on every trigger pull. For sandblasting, or two operators on high draw tools at once, start at 7.5 HP or move to a \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw compressor\u003c\/a\u003e rated for 100 percent duty.\u003c\/p\u003e\u003cp\u003eA two-stage compressor sends warm, wet air down the line, so pair this one with a refrigerated dryer rated above its 16.6 CFM output, such as the \u003ca href=\"\/products\/abac-cool-25-refrigerated-air-dryer-115v\"\u003eABAC COOL 25\u003c\/a\u003e, plus a filter regulator ahead of any paint or finishing work. The automatic tank drain clears condensate out of the receiver; it does nothing about moisture already carried downstream. Part of ABAC's 2-Stage Hybrid Pro range from the Atlas Copco group. Browse the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/air-dryers\"\u003ecompressed air dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V Single-Phase","offer_id":54557403382035,"sku":"8090304315","price":3353.0,"currency_code":"USD","in_stock":true},{"title":"230V Three-Phase","offer_id":54557403414803,"sku":"8090304349","price":3323.0,"currency_code":"USD","in_stock":true},{"title":"460V Three-Phase","offer_id":54557403447571,"sku":"8090304364","price":3323.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-ab5-2180vpff-80-gallon-premium-air-compressor.png?v=1786375998"},{"product_id":"abac-ab7-ff-7-5-hp-80-gallon-vertical-premium-air-compressor","title":"ABAC AB7-2180VFF 7.5 HP Two-Stage Air Compressor - 80 Gallon Vertical Premium, 175 PSI, 22.2 CFM T39 Pump","description":"\u003cp\u003eThe ABAC AB7-2180VFF is the Full Feature build of the 80 gallon vertical AB7 platform. The T39 two-stage hybrid pump pairs an aluminum head and aftercooler with cast iron cylinders, so heat and moisture come out of the air before it reaches the tank, and the FF specification adds a pressure-actuated automatic tank drain and a low oil level switch. It delivers 22.2 CFM at a maximum 175 PSI, and the same build is offered on 230V single-phase, 230V three-phase or 460V three-phase power.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AB7-2180VFF (230V 1-phase, Warthog 8090304414, ABAC 2021119423), AB7-2380VFF (230V 3-phase, Warthog 8090304463, ABAC 2021119425), AB7-4380VFF (460V 3-phase, Warthog 8090304497, ABAC 2021119427)\u003c\/li\u003e\n\u003cli\u003eFull Feature additions: pressure-actuated automatic tank drain, low oil level switch\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP\u003c\/li\u003e\n\u003cli\u003ePump: T39 two-stage hybrid, aluminum head and aftercooler with cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 22.2 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 80 gallon vertical, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eInner cooling technology, fully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eControl: start\/stop pressure switch\u003c\/li\u003e\n\u003cli\u003eDimensions: 25 x 34 x 75 in\u003c\/li\u003e\n\u003cli\u003eWeight: 413 lbs on the 230V single-phase build, 403 lbs on both three-phase builds\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat Full Feature buys you\u003c\/h3\u003e\u003cp\u003eTwo jobs keep a piston compressor alive: draining the condensate out of the receiver and keeping oil in the crankcase. Both are daily checks, and in a shop where the compressor belongs to nobody in particular, both get skipped. The pressure-actuated automatic drain bleeds the tank on its own, so water does not sit against the steel between services and rust the receiver from the inside. The low oil level switch watches the one failure that destroys a pump in minutes rather than months. If the compressor lives in a back corner and the person who used to check it has moved on, the FF specification is the version to buy. If somebody opens the drain every morning without being asked, the standard AB7-2180V saves the difference.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eEvery 80 gallon AB7 delivers the same 22.2 CFM at 175 PSI, so the choice comes down to footprint and what is fitted. The \u003ca href=\"\/products\/abac-ab7-7-5-hp-80-gallon-vertical-two-stage-air-compressor\"\u003eAB7-2180V\u003c\/a\u003e is the standard vertical build without the automatic drain and the oil level switch. The \u003ca href=\"\/products\/abac-ab7-hff-7-5-hp-80-gallon-horizontal-premium-air-compressor\"\u003eAB7-2180HFF\u003c\/a\u003e is this same Full Feature specification on a horizontal tank for shops without 75 inches of ceiling, and the \u003ca href=\"\/products\/abac-ab7-7-5-hp-80-gallon-horizontal-two-stage-air-compressor\"\u003eAB7-2180HS\u003c\/a\u003e is the standard horizontal. Where 22.2 CFM is more than the shop draws, the \u003ca href=\"\/products\/abac-ab5-2180vpff-5-hp-80-gallon-vertical-premium-air-compressor\"\u003e5 HP AB5-2180VPFF\u003c\/a\u003e runs 16.6 CFM on the same 80 gallon vertical tank in the same Full Feature trim. Two other 7.5 HP machines sit on the same 80 gallon vertical receiver and answer different constraints: the Ironman \u003ca href=\"\/products\/abac-abc7-ff-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eABC7-2180VFF\u003c\/a\u003e trades a little airflow, 21 CFM, for a fully cast iron C1 pump built for long duty cycles, and the \u003ca href=\"\/products\/abac-ab7-2180vqp-7-5-hp-quiet-power-80-gallon-air-compressor\"\u003eAB7-2180VQP Quiet Power\u003c\/a\u003e holds 22.3 CFM inside a sound enclosure at 69 dBA where the compressor shares space with people.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eBody shops, fabrication and welding bays, woodworking shops, tire and service work, and farm buildings: impact wrenching, grinding, orbital sanding, fastening, and air or water spraying where tools run through most of the shift. A two-stage pump recovers faster than a single-stage machine of the same horsepower, so two or three technicians can stay on tools without waiting on pressure. The vertical tank keeps the full 80 gallon reserve on a 25 by 34 inch footprint, which is most of the reason shops choose vertical over horizontal when the ceiling allows it.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eSpecify the voltage and phase that matches your panel before ordering, because the three builds are not field convertible. The 230V single-phase version draws the highest current of the three and normally wants a dedicated circuit sized to the motor nameplate; the 230V and 460V three-phase versions suit shops already on three-phase service. Plan for 75 inches of clear height plus room above for the discharge line, leave service clearance at the drain and the belt guard, and keep the intake away from paint fumes and sanding dust. Route the automatic drain discharge to a collection point rather than onto the floor, since what it bleeds is oily condensate. Belts, filters and oil are the routine service items on this range, so keep a set on the shelf.\u003c\/p\u003e\u003cp\u003eA two-stage pump still pushes warm, wet air into the line, so size a refrigerated dryer above the 22.2 CFM output, such as the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35\u003c\/a\u003e, before the air reaches paint, tires or pneumatic controls. Part of ABAC's 2-Stage Hybrid Pro range from the Atlas Copco group. Browse the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/air-dryers\"\u003ecompressed air dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V Single-Phase","offer_id":54557406626067,"sku":"8090304414","price":3846.0,"currency_code":"USD","in_stock":true},{"title":"230V Three-Phase","offer_id":54557406658835,"sku":"8090304463","price":3846.0,"currency_code":"USD","in_stock":true},{"title":"460V Three-Phase","offer_id":54557406691603,"sku":"8090304497","price":3846.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-ab7-vertical-ff-80-gallon-premium-air-compressor.png?v=1786376132"},{"product_id":"abac-ab7-hff-7-5-hp-80-gallon-horizontal-premium-air-compressor","title":"ABAC AB7-2180HFF 7.5 HP Two-Stage Air Compressor - 80 Gallon Horizontal Premium, 175 PSI, 22.2 CFM T39 Pump","description":"\u003cp\u003eThe ABAC AB7-2180HFF is the Full Feature build of the 80 gallon horizontal AB7 platform. The belt-driven T39 two-stage pump pairs an aluminum head and aftercooler with cast iron cylinders, so heat comes out of the air before it reaches the receiver, and the FF specification adds a pressure-actuated automatic tank drain and a low oil level switch. It delivers 22.2 CFM at a maximum 175 PSI on a low-profile tank that fits under benches, mezzanines and low ceilings where a 75 inch vertical machine will not. The same build is offered on 230V single-phase, 230V three-phase and 460V three-phase power.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AB7-2180HFF (230V\/1, part 8090304380), AB7-2380HFF (230V\/3, part 8090304430), 460V\/3 horizontal Full Feature (part 8090304471)\u003c\/li\u003e\n\u003cli\u003eFull Feature additions: pressure-actuated automatic tank drain, low oil level switch\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP\u003c\/li\u003e\n\u003cli\u003ePump: T39 two-stage hybrid, aluminum head and aftercooler with cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 22.2 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 80 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003eFully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eStart\/stop pressure switch control\u003c\/li\u003e\n\u003cli\u003eWeight: 413 lbs | Dimensions: 25\" x 71\" x 48\"\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year full, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eEvery 80 gallon AB7 runs the same T39 pump and the same 22.2 CFM at 175 PSI, so the choice is footprint and fitted equipment rather than output. The \u003ca href=\"\/products\/abac-ab7-7-5-hp-80-gallon-horizontal-two-stage-air-compressor\"\u003eAB7-2180HS\u003c\/a\u003e is this same horizontal machine without the automatic drain and the oil level switch. The \u003ca href=\"\/products\/abac-ab7-ff-7-5-hp-80-gallon-vertical-premium-air-compressor\"\u003eAB7-2180VFF\u003c\/a\u003e is the Full Feature specification on a vertical tank, 25 x 34 x 75 in, for shops with ceiling height but tight floor space, and the \u003ca href=\"\/products\/abac-ab7-7-5-hp-80-gallon-vertical-two-stage-air-compressor\"\u003eAB7-2180V\u003c\/a\u003e is the standard vertical. Where 22.2 CFM is more than the shop draws, the \u003ca href=\"\/products\/abac-ab5-2180vpff-5-hp-80-gallon-vertical-premium-air-compressor\"\u003e5 HP AB5-2180VPFF\u003c\/a\u003e runs 16.6 CFM in the same Full Feature trim. If a fully cast iron pump suits the duty better than the aluminum and cast iron hybrid, the \u003ca href=\"\/products\/abac-abc7-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eIronman ABC7-2180V\u003c\/a\u003e delivers 21 CFM from a C1 pump.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eMulti-bay auto repair and body shops, tire stores, welding and fabrication bays, woodworking shops and farm buildings with a height restriction: impact wrenching, grinding, orbital sanding, fastening, and air or water spraying where tools run through most of the shift. A two-stage pump recovers faster than a single-stage machine of the same horsepower, so several technicians can stay on tools without waiting on pressure, and the 80 gallon receiver keeps the pump from short cycling between tool triggers. The automatic drain and the oil level switch cover the two daily checks most often skipped where nobody is assigned to the compressor.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eSpecify the voltage and phase that matches your panel before ordering. The 230V single-phase version draws the highest current of the three and normally wants a dedicated circuit sized to the motor nameplate, while the 230V and 460V three-phase versions suit shops already running three-phase service. Allow for the 25 by 71 inch floor footprint and 48 inches of height, leave service clearance on the drain side where the discharge and tank drain sit low on a horizontal tank, and keep the intake away from paint fumes and sanding dust. Belts, filters and oil are the routine service items on this range.\u003c\/p\u003e\u003cp\u003eA two-stage pump still pushes warm, wet air into the line, so size a refrigerated dryer above the 22.2 CFM output, such as the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35\u003c\/a\u003e, before the air reaches paint, tires or pneumatic controls. Part of ABAC's 2-Stage Hybrid Pro range from the Atlas Copco group. Browse the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/air-dryers\"\u003ecompressed air dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V Single-Phase","offer_id":54557408362771,"sku":"8090304380","price":3846.0,"currency_code":"USD","in_stock":true},{"title":"230V Three-Phase","offer_id":54557408395539,"sku":"8090304430","price":3846.0,"currency_code":"USD","in_stock":true},{"title":"460V Three-Phase","offer_id":54557408428307,"sku":"8090304471","price":3846.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-ab7-2180hff-80-gallon-horizontal-premium.jpg?v=1791396350"},{"product_id":"abac-abc5-ff-5-hp-80-gallon-vertical-ironman-air-compressor","title":"ABAC ABC5-2180VFFS 5 HP Two-Stage Ironman Air Compressor - 80 Gallon Vertical Full Feature, 175 PSI, 16 CFM C1 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC5 Full Feature pairs the Ironman all cast iron two-stage pump with ABAC's FF protection package, so the machine looks after itself between shifts. A 5 HP motor drives the C1 cast iron pump to 16 CFM at a maximum 175 PSI on an \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/vertical-air-compressor-tanks\"\u003e80 gallon vertical ASME tank\u003c\/a\u003e. Choose 230V single-phase (ABC5-2180VFFS), 230V three-phase (ABC5-2380VFF), 460V three-phase (ABC5-4380VFF), or 575V three-phase (ABC5-5380VFF).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC5-2180VFFS \/ ABC5-2380VFF \/ ABC5-4380VFF \/ ABC5-5380VFF\u003c\/li\u003e\n\u003cli\u003eABAC part numbers: 2020041765 (230\/1), 2020041767 (230\/3), 2020041769 (460\/3)\u003c\/li\u003e\n\u003cli\u003eFull Feature package: automatic tank drain and low oil level shutoff\u003c\/li\u003e\n\u003cli\u003eMotor: 5 HP\u003c\/li\u003e\n\u003cli\u003ePump: C1 two-stage, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 16 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 80 gallon vertical, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60, 230\/3\/60, 460\/3\/60, or 575\/3\/60\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eWeight: 580 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 24 x 36 x 72 in (L x W x H)\u003c\/li\u003e\n\u003cli\u003eAssembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat the Full Feature package adds\u003c\/h3\u003e\u003cp\u003eTwo things, and both of them are jobs a busy shop forgets. The automatic tank drain clears condensate on its own, so nobody has to remember the petcock at closing time and the bottom of the receiver does not quietly rust through. The low oil level shutoff stops the motor before the pump runs dry, which is the failure that turns a pump rebuild into a pump replacement. If your crew is reliable about both chores, the standard \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc5-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eABC5 Ironman\u003c\/a\u003e is the same machine without the FF package.\u003c\/p\u003e\u003ch3\u003eWhat 16 CFM actually runs\u003c\/h3\u003e\u003cp\u003eSixteen CFM at 175 PSI suits a one or two bay shop running tools one at a time: impact wrenches, air ratchets, hammers, blow guns, nailers, and a touch up gun. Continuous draw work is where it runs out of room. A sandblaster, a production DA sander worked all shift, or two techs on air at once will pull the pressure down faster than the pump recovers. For that load, step up to the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc7-ff-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eABC7 Full Feature at 21 CFM\u003c\/a\u003e or move to a \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/rotary-screw-air-compressors\"\u003erotary screw\u003c\/a\u003e, which is rated for 100 percent duty.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eAuto repair and body shops, tire stores, \u003ca href=\"https:\/\/aircompressorstore.com\/blogs\/featured-articles\/compressed-air-for-woodworking-shops\"\u003ewoodworking shops\u003c\/a\u003e, and light fabrication running air tools through the full workday. The Full Feature build suits shops that would rather not rely on someone remembering to drain the tank or check the oil.\u003c\/p\u003e\u003ch3\u003eInstallation and air treatment\u003c\/h3\u003e\u003cp\u003eAt 580 lbs on a 24 x 36 x 72 in footprint this is a floor-standing machine: set it level, leave room on the cooling side, and run it on a dedicated circuit sized to the motor nameplate. The 230V single-phase version is the one most small shops can actually power; 460V and 575V three-phase are the long term choice wherever three phase is already in the building. Compressed air leaving an 80 gallon receiver still carries water, so if the air reaches paint, plasma, or pneumatic controls, add a refrigerated dryer. The \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-cool-25-refrigerated-air-dryer-115v\"\u003eABAC COOL 25\u003c\/a\u003e is rated above this compressor's 16 CFM output and leaves headroom on a hot day. Browse all \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. The vertical 80 gallon footprint keeps floor space free while holding enough stored air to smooth out demand spikes, and the all cast iron two-stage pump is the part of this machine that decides how many years it lasts.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54637803864339,"sku":"8090303804","price":3651.0,"currency_code":"USD","in_stock":true},{"title":"230V 3-Phase","offer_id":54637803897107,"sku":"8090303820","price":3651.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54637803929875,"sku":"8090303846","price":3651.0,"currency_code":"USD","in_stock":true},{"title":"575V 3-Phase","offer_id":54637803962643,"sku":"8090303861","price":3923.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc5-ff-80-gallon-vertical-ironman-air-compressor.png?v=1788218286"},{"product_id":"abac-abc7-ff-7-5-hp-80-gallon-vertical-ironman-air-compressor","title":"ABAC ABC7-2180VFF 7.5 HP Two-Stage Ironman Air Compressor - 80 Gallon Vertical Full Feature, 175 PSI, 21 CFM C1 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC7 Full Feature pairs the Ironman all cast iron two-stage pump with ABAC's FF protection package, so the machine looks after itself between shifts. A 7.5 HP motor drives the C1 cast iron pump to 21 CFM at a maximum 175 PSI on an \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/vertical-air-compressor-tanks\"\u003e80 gallon vertical ASME tank\u003c\/a\u003e. Choose 230V single-phase (ABC7-2180VFF), 230V three-phase (ABC7-2380VFF), 460V three-phase (ABC7-4380VFF), or 575V three-phase (ABC7-5380VFF).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC7-2180VFF \/ ABC7-2380VFF \/ ABC7-4380VFF \/ ABC7-5380VFF\u003c\/li\u003e\n\u003cli\u003eFull Feature package: automatic tank drain, low oil level automatic shutoff, and belt guard aftercooler\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP\u003c\/li\u003e\n\u003cli\u003ePump: C1 two-stage, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 21 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 80 gallon vertical, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60, 230\/3\/60, 460\/3\/60, or 575\/3\/60\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eMagnetic starter and discharge valve fitted as standard\u003c\/li\u003e\n\u003cli\u003eWarranty: 2 year, assembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat the Full Feature package adds\u003c\/h3\u003e\u003cp\u003eThree things, and all three are jobs a busy shop forgets or cannot do by hand at all. The automatic tank drain clears condensate on its own, so nobody has to remember the petcock at closing time and the bottom of the receiver does not quietly rust through. The low oil level automatic shutoff stops the motor before the pump runs dry, which is the failure that turns a pump rebuild into a pump replacement. The belt guard aftercooler is the one no habit can replace: it drops the discharge temperature before the air reaches the tank, so a large share of the moisture condenses in the receiver where the drain can get rid of it, rather than travelling down the pipe to your tools. If your crew is reliable about the first two chores and the air does not need to be dry, the standard \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc7-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eABC7-2180V\u003c\/a\u003e is the same 21 CFM machine without the FF package.\u003c\/p\u003e\u003ch3\u003eWhat 21 CFM actually runs\u003c\/h3\u003e\u003cp\u003eSize on CFM, not on horsepower. Twenty one CFM at 175 PSI covers impact wrenches, air ratchets, hammers, blow guns, grinders and a spray gun, and holds pressure when a second tool joins in for a while. Below it, the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc5-ff-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eABC5 Full Feature at 16 CFM\u003c\/a\u003e suits a one or two bay shop running tools one at a time. On this same 7.5 HP vertical platform the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc7-v2-ff-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eABC7-2180V2FF\u003c\/a\u003e steps up to the larger C2 pump for 24 CFM, which is the move if a continuous duty tool such as a dual action sander will run most of the day. For two operators on air at once, start instead at the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc10-ff-10-hp-120-gallon-vertical-ironman-air-compressor\"\u003e10 HP ABC10 Full Feature at 32 CFM\u003c\/a\u003e on a 120 gallon receiver. Sustained work such as sandblasting belongs on a \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/rotary-screw-air-compressors\"\u003erotary screw\u003c\/a\u003e, which is rated for 100 percent duty.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eAuto repair and body shops, tire stores, \u003ca href=\"https:\/\/aircompressorstore.com\/blogs\/featured-articles\/compressed-air-for-woodworking-shops\"\u003ewoodworking shops\u003c\/a\u003e, metal shops and light fabrication running air tools through the full workday: equipment operation, grinding, hammering, tire inflation, fastening, orbital sanding and spraying. The Full Feature build suits shops that would rather not rely on someone remembering to drain the tank or check the oil.\u003c\/p\u003e\u003ch3\u003ePower and air treatment\u003c\/h3\u003e\u003cp\u003eTake three-phase power if the panel has it, since a three-phase motor starts easier and runs cooler on a compressor that cycles all day, and the 460V build keeps the wire size down on a long run. On single-phase, give it a dedicated circuit sized to the motor nameplate and keep the wire run short. The belt guard aftercooler does real work on moisture, but it is not a dryer: if the air reaches paint, plasma, or pneumatic controls, add a refrigerated dryer rated above this compressor's 21 CFM output. The \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35\u003c\/a\u003e leaves headroom on a hot day. Browse all \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. The vertical 80 gallon footprint keeps floor space free while holding enough stored air to smooth out demand spikes, and the all cast iron two-stage pump is the part of this machine that decides how many years it lasts. See the rest of our \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/7-5-hp-air-compressors\"\u003e7.5 HP air compressors\u003c\/a\u003e and the full \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/piston-air-compressors\"\u003episton air compressor\u003c\/a\u003e range.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54637876052243,"sku":"8090303887","price":3786.0,"currency_code":"USD","in_stock":true},{"title":"230V 3-Phase","offer_id":54637876085011,"sku":"8090303903","price":3786.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54637876117779,"sku":"8090303929","price":3786.0,"currency_code":"USD","in_stock":true},{"title":"575V 3-Phase","offer_id":54637876150547,"sku":"8090303945","price":3786.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc7-ff-80-gallon-vertical-ironman-air-compressor.png?v=1788221961"},{"product_id":"abac-abc7-v2-ff-7-5-hp-80-gallon-vertical-ironman-air-compressor","title":"ABAC ABC7-2180V2FF 7.5 HP Two-Stage Ironman Air Compressor - 80 Gallon Vertical Full Feature, 175 PSI, 24 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC7 V2 Full Feature pairs the larger C2 cast iron pump with ABAC's FF protection package, so the machine looks after itself between shifts. A 7.5 HP motor drives the C2 two-stage pump to 24 CFM at a maximum 175 PSI on an \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/vertical-air-compressor-tanks\"\u003e80 gallon vertical ASME tank\u003c\/a\u003e. Choose 230V single-phase (ABC7-2180V2FF), 230V three-phase (ABC7-2380V2FF), 460V three-phase (ABC7-4380V2FF), or 575V three-phase (ABC7-5380V2FF).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC7-2180V2FF \/ ABC7-2380V2FF \/ ABC7-4380V2FF \/ ABC7-5380V2FF\u003c\/li\u003e\n\u003cli\u003eFull Feature package: automatic tank drain, low oil level automatic shut off, and belt guard aftercooler\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP\u003c\/li\u003e\n\u003cli\u003ePump: C2 two-stage, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 24 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 80 gallon vertical, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60, 230\/3\/60, 460\/3\/60, or 575\/3\/60\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guard\u003c\/li\u003e\n\u003cli\u003eDimensions: 25 x 41 x 71 in\u003c\/li\u003e\n\u003cli\u003eWeight: 694 lbs\u003c\/li\u003e\n\u003cli\u003eAssembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat the Full Feature package adds\u003c\/h3\u003e\u003cp\u003eThree things, and all three are jobs a busy shop forgets or cannot do by hand at all. The automatic tank drain clears condensate on its own, so nobody has to remember the petcock at closing time and the bottom of the receiver does not quietly rust through. The low oil level automatic shut off stops the motor before the pump runs dry, which is the failure that turns a pump rebuild into a pump replacement. The belt guard aftercooler is the one no habit can replace: it drops the discharge temperature before the air reaches the tank, so a large share of the moisture condenses in the receiver where the drain can get rid of it instead of travelling down the pipe to your tools. If the crew is reliable about the first two chores and the air does not need to be dry, the standard \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc7-v2-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eABC7-2180V2\u003c\/a\u003e is the same 24 CFM machine without the FF package.\u003c\/p\u003e\u003ch3\u003eWhy the larger pump matters\u003c\/h3\u003e\u003cp\u003eAir delivery on a piston compressor comes from pump displacement and pump speed, not from the motor badge. The C2 is the bigger of the two Ironman cast iron blocks, so on the same 7.5 HP motor it reaches 24 CFM while turning slower than the C1 does for 21 CFM. Lower pump speed means lower piston speed, less heat and less wear per hour of running, which is the argument for buying displacement rather than RPM. The extra iron shows on the scale: 694 lbs on a 25 x 41 in footprint, against 622 lbs for the C1 Full Feature build. Two stages handle the rest, compressing in two steps with cooling in between, so 175 PSI arrives without the heat a single-stage pump makes chasing the same pressure.\u003c\/p\u003e\u003ch3\u003eWhat 24 CFM actually runs\u003c\/h3\u003e\u003cp\u003eSize on CFM, not on horsepower. Twenty four CFM at 175 PSI holds pressure under a continuous duty tool such as a dual action sander, or under two techs on impact tools and blow guns at the same time. Below it, the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc7-ff-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003eABC7-2180VFF at 21 CFM\u003c\/a\u003e is the same Full Feature build on the C1 pump and suits tools that run in bursts rather than all day, and the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc5-ff-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003e5 HP ABC5 Full Feature at 16 CFM\u003c\/a\u003e covers a one or two bay shop running tools one at a time. Above it, the \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-abc10-ff-10-hp-120-gallon-vertical-ironman-air-compressor\"\u003e10 HP ABC10 Full Feature at 32 CFM\u003c\/a\u003e moves to a 120 gallon receiver, which is where to start if a third operator is likely. Sustained work such as sandblasting belongs on a \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/rotary-screw-air-compressors\"\u003erotary screw\u003c\/a\u003e, which is rated for 100 percent duty.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eBusy auto and truck repair shops, tire and fleet service bays, cabinet and \u003ca href=\"https:\/\/aircompressorstore.com\/blogs\/featured-articles\/compressed-air-for-woodworking-shops\"\u003ewoodworking shops\u003c\/a\u003e, and light fabrication where several air tools run at once and the compressor is expected to keep up all day rather than catch up between jobs. The 80 gallon reserve smooths demand spikes so the pump is not restarting on every trigger pull, and the Full Feature build suits shops that would rather not rely on someone remembering to drain the tank or check the oil.\u003c\/p\u003e\u003ch3\u003ePower and air treatment\u003c\/h3\u003e\u003cp\u003eTake three-phase power if the panel has it. A three-phase motor starts easier and runs cooler on a compressor that cycles all day, and the 460V build keeps wire size down on a long run. On single-phase, give it a dedicated circuit sized to the motor nameplate and keep the wire run short. The belt guard aftercooler does real work on moisture, but it is not a dryer: if the air reaches paint, plasma, or pneumatic controls, add a refrigerated dryer rated above this compressor's 24 CFM output. The \u003ca href=\"https:\/\/aircompressorstore.com\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35\u003c\/a\u003e leaves headroom on a hot day. Browse all \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003ePart of ABAC's Ironman cast iron range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. The vertical 80 gallon footprint keeps floor space free while holding enough stored air to smooth out demand spikes, and the all cast iron two-stage pump is the part of this machine that decides how many years it lasts. See the rest of our \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/7-5-hp-air-compressors\"\u003e7.5 HP air compressors\u003c\/a\u003e and the full \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/piston-air-compressors\"\u003episton air compressor\u003c\/a\u003e range.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54637943095571,"sku":"8090304158","price":4572.0,"currency_code":"USD","in_stock":true},{"title":"230V 3-Phase","offer_id":54637943128339,"sku":"8090304174","price":4572.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54637943161107,"sku":"8090304190","price":4572.0,"currency_code":"USD","in_stock":true},{"title":"575V 3-Phase","offer_id":54637943193875,"sku":"8090304216","price":4572.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc7-v2-ff-80-gallon-vertical-ironman-air-compressor.png?v=1789404495"},{"product_id":"abac-abc10-ff-10-hp-120-gallon-horizontal-ironman-air-compressor","title":"ABAC ABC10-23120HFF 10 HP Two-Stage Ironman Air Compressor - 120 Gallon Horizontal Full Feature, 175 PSI, 32 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC10-23120HFF puts the 10 HP Ironman on a \u003ca href=\"\/collections\/horizontal-air-compressor-tanks\"\u003e120 gallon horizontal ASME tank\u003c\/a\u003e and adds ABAC's Full Feature protection package, so the machine looks after itself between shifts. The C2 four cylinder V shape cast iron pump delivers 32 CFM at a maximum 175 PSI. The horizontal layout sits low and long at 50 inches tall, which suits shops that would rather run the compressor along a wall or under a mezzanine than give up floor space to a vertical footprint. This is a three-phase machine only. Choose 230V three-phase (ABC10-23120HFF), 460V three-phase (ABC10-43120HFF), or 575V three-phase (ABC10-53120HFF).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC10-23120HFF \/ ABC10-43120HFF \/ ABC10-53120HFF\u003c\/li\u003e\n\u003cli\u003eFull Feature package: automatic tank drain, low oil level automatic shut off, and belt guard aftercooler\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP\u003c\/li\u003e\n\u003cli\u003ePump: C2 two-stage, four cylinder V shape, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 32 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon horizontal, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/3\/60, 460\/3\/60, or 575\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 728 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 27 x 74 x 50 in\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guard, discharge valve, magnetic starter\u003c\/li\u003e\n\u003cli\u003eAssembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eThe same 10 HP Ironman and the same 32 CFM at 175 PSI are also sold on a vertical receiver. The \u003ca href=\"\/products\/abac-abc10-ff-10-hp-120-gallon-vertical-ironman-air-compressor\"\u003e120 gallon vertical Full Feature\u003c\/a\u003e is 765 lbs at 30 x 41 x 74 in and gives back the floor where there is ceiling height to spare, while this horizontal build is 728 lbs at 27 x 74 x 50 in and keeps overall height down where clearance is tight. Airflow is identical, so pick on the space you have. If the Full Feature additions are not needed, the \u003ca href=\"\/products\/abac-abc10-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003estandard ABC10 horizontal\u003c\/a\u003e is the same pump and tank without the automatic drain, low oil shut off or aftercooler. Below this sits the \u003ca href=\"\/products\/abac-abc7-v2-ff-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003e7.5 HP ABC7-2180V2FF\u003c\/a\u003e at 24 CFM on an 80 gallon vertical tank, which is the right call when the duty is one or two tools at a time rather than a full bay. Alongside it, the \u003ca href=\"\/products\/abac-abc5-duplex-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC5-21120HD duplex\u003c\/a\u003e reaches the same 32 CFM from two 5 HP pumps on one 120 gallon horizontal tank, which buys alternating control and a second pump to fall back on rather than more air.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction shops, fabrication and welding bays, truck and fleet maintenance, tire shops running multiple lifts, and any operation where several \u003ca href=\"\/collections\/tools\"\u003eair tools\u003c\/a\u003e or a plasma cutter draw at the same time and the compressor needs to hold pressure through the shift rather than recover between jobs. The 120 gallon receiver cuts motor starts and holds a steadier line pressure than an 80 gallon build, which matters most on intermittent duty where a smaller tank would short cycle the pump. The Full Feature build suits shops that would rather not rely on someone remembering to drain the tank or check the oil.\u003c\/p\u003e\u003cp\u003eThe belt guard aftercooler drops discharge temperature before the air reaches the tank, so less condensate is carried downstream into tools and filters. On a 32 CFM machine feeding paint, plasma or pneumatic instruments, pair it with a \u003ca href=\"\/collections\/air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e sized at or above 32 CFM and a filter regulator at the drop. Part of ABAC's Ironman cast iron range from the Atlas Copco group. See the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 3-Phase","offer_id":54638092681491,"sku":"8090303960","price":5324.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54638092714259,"sku":"8090304000","price":5324.0,"currency_code":"USD","in_stock":true},{"title":"575V 3-Phase","offer_id":54638092747027,"sku":"8090304042","price":5595.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc10-120-gallon-horizontal-full-feature-air-compressor.png?v=1788228625"},{"product_id":"abac-abc10-ff-10-hp-120-gallon-vertical-ironman-air-compressor","title":"ABAC ABC10-23120VFF 10 HP Two-Stage Ironman Air Compressor - 120 Gallon Vertical Full Feature, 175 PSI, 32 CFM C2 Cast Iron Pump","description":"\u003cp\u003eThe ABAC ABC10-23120VFF puts the 10 HP Ironman on a \u003ca href=\"\/collections\/vertical-air-compressor-tanks\"\u003e120 gallon vertical ASME tank\u003c\/a\u003e and adds ABAC's Full Feature protection package, so the machine looks after itself between shifts. The C2 four cylinder V shape cast iron pump delivers 32 CFM at a maximum 175 PSI. The vertical layout puts that storage into a compact floor footprint, which is what most shops want when wall and bay space is already committed and there is ceiling height to spare. This is a three-phase machine only. Choose 230V three-phase (ABC10-23120VFF), 460V three-phase (ABC10-43120VFF), or 575V three-phase (ABC10-53120VFF).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: ABC10-23120VFF \/ ABC10-43120VFF \/ ABC10-53120VFF\u003c\/li\u003e\n\u003cli\u003eFull Feature package: automatic tank drain, low oil level automatic shut off, and belt guard aftercooler\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP\u003c\/li\u003e\n\u003cli\u003ePump: C2 two-stage, four cylinder V shape, cast iron cylinders\u003c\/li\u003e\n\u003cli\u003eAir delivery: 32 CFM at max pressure\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eTank: 120 gallon vertical, ASME tank and safety valves\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/3\/60, 460\/3\/60, or 575\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 765 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 30 x 41 x 74 in\u003c\/li\u003e\n\u003cli\u003eBelt drive with fully enclosed belt guard, discharge valve, magnetic starter\u003c\/li\u003e\n\u003cli\u003eAssembled in the USA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat Full Feature adds\u003c\/h3\u003e\u003cp\u003eFull Feature is ABAC's protection package, and on this build it is three things. The automatic tank drain clears condensate out of the bottom of the 120 gallon receiver without anyone opening a petcock, which is the maintenance step shops skip most often and the one that rusts a tank from the inside out. The low oil level automatic shut off stops the motor before the pump runs dry, so a slow leak or a missed oil check does not cost a crankshaft. The belt guard aftercooler drops discharge temperature before the air reaches the tank, so a large share of the moisture drops out in the receiver instead of travelling downstream into tools, filters and spray equipment. Mechanically this is the same 10 HP motor and the same C2 pump as the standard ABC10 vertical. Full Feature changes what the machine does between shifts, not what it delivers.\u003c\/p\u003e\u003ch3\u003eWhy the cast iron pump matters\u003c\/h3\u003e\u003cp\u003eABAC builds the Ironman pump with fully cast iron construction and a four cylinder V shape arrangement, which is what lifts this 10 HP machine to 32 CFM. Cast iron cylinders carry heat away better than aluminium and tolerate the long loaded runs that a production bay imposes, which is most of the reason a 10 HP Ironman weighs 765 lbs. That weight is the trade: this is a machine to anchor in one place and pipe properly, not one to move around.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eThe same 10 HP Ironman and the same 32 CFM at 175 PSI are also sold on a horizontal receiver. The \u003ca href=\"\/products\/abac-abc10-ff-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003e120 gallon horizontal Full Feature\u003c\/a\u003e is 728 lbs at 27 x 74 x 50 in, so it sits low and long under a mezzanine or along a wall, while this vertical build is 765 lbs at 30 x 41 x 74 in and gives back the floor. Airflow is identical, so pick on the space you have. If the Full Feature additions are not needed, the \u003ca href=\"\/products\/abac-abc10-10-hp-120-gallon-vertical-ironman-air-compressor\"\u003estandard ABC10 vertical\u003c\/a\u003e is the same pump and tank without the automatic drain, low oil shut off or aftercooler. Below this sits the \u003ca href=\"\/products\/abac-abc7-v2-ff-7-5-hp-80-gallon-vertical-ironman-air-compressor\"\u003e7.5 HP ABC7-2180V2FF\u003c\/a\u003e at 24 CFM on an 80 gallon vertical tank, which is the right call when the duty is one or two tools at a time rather than a full bay. Alongside it, the \u003ca href=\"\/products\/abac-abc5-duplex-10-hp-120-gallon-horizontal-ironman-air-compressor\"\u003eABC5-21120HD duplex\u003c\/a\u003e reaches the same 32 CFM from two 5 HP pumps on one 120 gallon horizontal tank, which buys alternating control and a second pump to fall back on rather than more air, though only on a horizontal footprint.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction shops, fabrication and welding bays, truck and fleet maintenance, tire shops running multiple lifts, and any operation where several \u003ca href=\"\/collections\/tools\"\u003eair tools\u003c\/a\u003e or a plasma cutter draw at the same time and the compressor needs to hold pressure through the shift rather than recover between jobs. The 120 gallon receiver cuts motor starts and holds a steadier line pressure than an 80 gallon build, which matters most on intermittent duty where a smaller tank would short cycle the pump. The Full Feature build suits shops that would rather not rely on someone remembering to drain the tank or check the oil.\u003c\/p\u003e\u003ch3\u003eSizing the air treatment\u003c\/h3\u003e\u003cp\u003eAn aftercooler knocks a good share of the water out of the air, but it does not dry it. On a 32 CFM machine feeding paint, plasma or pneumatic instruments, follow the compressor with a refrigerated dryer rated at or above its output: the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35\u003c\/a\u003e is rated 35 CFM and runs on a standard 115V outlet, so it covers this machine with margin to spare. Add a filter regulator at each drop and run the take offs off the top of the header so condensate stays in the main. Part of ABAC's Ironman cast iron range from the Atlas Copco group. See the rest of our \u003ca href=\"\/collections\/piston-air-compressors\"\u003episton air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 3-Phase","offer_id":54638260257043,"sku":"8090303986","price":5649.0,"currency_code":"USD","in_stock":true},{"title":"460V 3-Phase","offer_id":54638260289811,"sku":"8090304026","price":5649.0,"currency_code":"USD","in_stock":true},{"title":"575V 3-Phase","offer_id":54638260322579,"sku":"8090304067","price":5649.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-abc10-ff-120-gallon-vertical-ironman-air-compressor.png?v=1789403336"}],"url":"https:\/\/aircompressorstore.com\/collections\/abac-full-feature-air-compressors.oembed","provider":"Warthog Air Compressor Store","version":"1.0","type":"link"}