{"title":"ABAC 71 Gallon Air Compressors","description":"\u003ch2\u003eABAC 71 Gallon Air Compressors\u003c\/h2\u003e\n\u003cp\u003eSeventy one gallons is the smaller of the two receivers ABAC mounts its AS rotary screw compressors on, and it covers the 5, 7.5 and 10 HP end of the range. A screw compressor runs continuously rather than cycling, so this tank is not sized to stop short cycling. It is there to steady line pressure through demand spikes and give the air somewhere to cool and drop water before it reaches the shop. On a smaller machine that job does not need a 131 gallon receiver, and the shorter skid is easier to place against a wall.\u003c\/p\u003e\n\u003cp\u003eThe range delivers 17.4 CFM on the 5 HP at 150 PSI up to 36.4 CFM on the 10 HP at 125 PSI, at 63 to 69 dBA. Each model is sold two ways. The plain tank mount puts the compressor and receiver on one frame. The tank mount with dryer adds an integrated refrigerated dryer on the same skid, which is the simpler buy if the shop runs spray guns, plasma, or air tools that will not tolerate moisture. The 5 HP pair at 63 dBA is quiet enough to sit in an occupied work area rather than a separate compressor room.\u003c\/p\u003e\n\u003cp\u003eNeed more stored air? The same 7.5 and 10 HP pumps are offered on a \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-131-gallon-air-compressors\"\u003e131 gallon receiver\u003c\/a\u003e, and the whole AS range is also sold \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-base-mount-rotary-screw-air-compressors\"\u003ebase mount\u003c\/a\u003e to pipe into a tank you already own. Compare every machine with onboard drying in \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-rotary-screw-air-compressors-with-dryer\"\u003erotary screw compressors with integrated dryer\u003c\/a\u003e, see the full \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-rotary-screw-air-compressors\"\u003eABAC AS rotary screw range\u003c\/a\u003e, or browse the brand in \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-air-compressors\"\u003eABAC air compressors\u003c\/a\u003e. A standalone \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-cool-refrigerated-air-dryers\"\u003eABAC COOL refrigerated dryer\u003c\/a\u003e suits any machine bought without one.\u003c\/p\u003e","products":[{"product_id":"abac-as-5-5-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor","title":"ABAC AS-5251TM 5 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount, 125 PSI, 20.3 CFM, 63 dBA","description":"\u003cp\u003eThe ABAC AS-5251TM is a 5 HP rotary screw air compressor built for shops that run air continuously rather than in bursts. It delivers 20.3 CFM at 125 PSI and runs at 63 dBA, quiet enough to sit in the work area instead of a separate compressor room. The compressor arrives already mounted on a 71 gallon air receiver, so it lands as one 56 x 23 x 55 in package with no separate tank to source or plumb. Choose 230V single-phase (AS-5251TM) or 208-230-460V three-phase (AS-5253TM).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AS-5251TM (part number 4152044119, 230V single-phase) and AS-5253TM (part number 4152043889, 208-230-460V three-phase)\u003c\/li\u003e\n\u003cli\u003eMotor: 5 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 20.3 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 63 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 71 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 485 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 56 x 23 x 55 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eThree stage vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eDuty cycle: rated for continuous running\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw turns continuously, so it holds a steady line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops move off a piston machine that is cycling hard, running hot and filling the room with noise. ABAC builds the AS-B air end as a fully integrated aluminum block with a three stage vertical oil separation process, which keeps oil carryover and condensation low, and pairs it with an energy efficient motor and a digital controller that tracks the service intervals on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, so it wants a receiver sized to its output and a demand pattern that keeps it loaded. The 71 gallon tank on this build is matched to the air end for exactly that reason.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eThe same 5 HP air end is sold three ways. The \u003ca href=\"\/products\/abac-as-5-5-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-5251BM base mount\u003c\/a\u003e is the compressor on its own, 335 lbs on a 32 x 24 x 40 in footprint, for a shop that already has a receiver. This tank mount build adds the 71 gallon receiver and comes in at 485 lbs. The \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-5251TMD\u003c\/a\u003e adds a refrigerated dryer on the same 56 x 23 x 55 in frame at 571 lbs. If your tools need line pressure above 125 PSI, the \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-5501TM 150 PSI build\u003c\/a\u003e trades airflow for pressure at 17.4 CFM. If you need more air, the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003e7.5 HP AS-7.5251TM7\u003c\/a\u003e delivers 30.5 CFM on the same 71 gallon platform at 507 lbs and 67 dBA. Pick on CFM first, then on pressure, then on whether you want the tank and the dryer in the same package.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC rates the AS-B range for professional and industrial work where the air supply has to be continuous and the operating conditions are demanding: heavy assembly, production line assembly, and cleaning and preparation. In practice that means automotive service bays, tire shops, small production and fabrication floors, cabinet and woodworking shops, and any operation where a piston compressor is cycling too hard to keep up. At 20.3 CFM the AS-5251TM suits a bay running impact tools, an orbital sander or a small plasma cutter, with headroom for intermittent work at a second station. It is not the machine for sandblasting or for several impact wrenches drawing at once; that is where the 7.5 HP and 10 HP builds start.\u003c\/p\u003e\u003ch3\u003eInstallation and air treatment\u003c\/h3\u003e\u003cp\u003eA screw compressor delivers warm, wet air, so plan the downstream side with it. Leave clearance on the cooling air side, keep the room out of the extremes of heat, and run the unit on its own circuit sized to the motor nameplate. At 485 lbs this arrives on a pallet and wants a forklift or a pallet jack at delivery, so allow for the 56 x 23 x 55 in footprint plus service clearance when you pick the spot. Add a \u003ca href=\"\/products\/abac-cool-25-refrigerated-air-dryer-115v\"\u003eCOOL 25 refrigerated air dryer\u003c\/a\u003e and a filter regulator if the air goes to paint, tires or anything that hates water; the COOL 25 runs on a 115V outlet, so it plugs in beside the compressor without new wiring, and it covers the full 20.3 CFM output. The \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-5251TMD\u003c\/a\u003e above is the same machine with that dryer already integrated and already matched to the output. Oil, oil filter and separator element are the service items, so keep a spare set on the shelf. Call us with your tool list and duty cycle and we will check this machine against the demand before you pipe it in.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the Atlas Copco group. See the full \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressor\u003c\/a\u003e range, the \u003ca href=\"\/collections\/fixed-speed-rotary-screw-air-compressors\"\u003efixed speed screw compressors\u003c\/a\u003e, all \u003ca href=\"\/collections\/5-hp-air-compressors\"\u003e5 HP air compressors\u003c\/a\u003e, or our \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at 109 PSI for 125 PSI maximum units. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54708869824787,"sku":"4152044119","price":6184.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54708869857555,"sku":"4152043889","price":6184.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-tank-mount-rotary-screw-air-compressor.png?v=1790946107"},{"product_id":"abac-as-5-5-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor","title":"ABAC AS-5501TM 5 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount, 150 PSI, 17.4 CFM, 63 dBA","description":"\u003cp\u003eThe ABAC AS-5501TM is a 5 HP rotary screw air compressor built for shops that run air continuously rather than in bursts. This 150 PSI build delivers 17.4 CFM and runs at 63 dBA, quiet enough to sit in the work area instead of a separate compressor room. The higher pressure setting suits tools and equipment that need more than a standard 125 PSI line. The compressor arrives already mounted on a 71 gallon air receiver, so it lands as a single 485 lb package with no separate tank to source or plumb. Choose 230V single-phase (AS-5501TM) or 208-230-460V three-phase (AS-5503TM).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AS-5501TM (230\/1\/60, part number 4152044120) \/ AS-5503TM (208-230-460\/3\/60, part number 4152043890)\u003c\/li\u003e\n\u003cli\u003eMotor: 5 HP\u003c\/li\u003e\n\u003cli\u003eAir delivery: 17.4 CFM\u003c\/li\u003e\n\u003cli\u003eWorking pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 63 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 71 gallon air receiver\u003c\/li\u003e\n\u003cli\u003eWeight: 485 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 56 x 23 x 55 in\u003c\/li\u003e\n\u003cli\u003eIntegrated aluminum compressor block\u003c\/li\u003e\n\u003cli\u003eThree-stage vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eAutomotive service bays, tire shops, small production and fabrication floors, cabinet and woodworking shops, and any operation where a piston compressor is cycling too hard to keep up. A rotary screw is built for continuous running, so it holds a steady line pressure through a full shift instead of recovering between jobs. The 150 PSI rating gives headroom for impact tools, presses and equipment that fall off at a standard 125 PSI supply. At 17.4 CFM the AS-5501TM suits a single busy bay, or a second station running intermittently alongside it.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eThe same 5 HP air end is sold four ways, and the choice comes down to pressure, receiver and air treatment. The \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003e125 PSI version of this machine\u003c\/a\u003e trades pressure for air delivery at 20.3 CFM on the identical 485 lb package, so choose on whether your tools are short of pressure or short of volume. Shops that already own a receiver can take the \u003ca href=\"\/products\/abac-as-5-5-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-5501BM base mount\u003c\/a\u003e, which is the compressor on its own at 335 lbs on a 32 x 24 x 40 in footprint. If finishing work or pneumatic controls mean moisture has to come out of the line, the \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-5501TMD\u003c\/a\u003e adds a refrigerated dryer on the same 56 x 23 x 55 in frame at 571 lbs. If 17.4 CFM is going to be tight, the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003e7.5 HP AS-7.5501TM7\u003c\/a\u003e delivers 27.1 CFM at the same 150 PSI on the same 71 gallon platform.\u003c\/p\u003e\u003ch3\u003eInstallation and air treatment\u003c\/h3\u003e\u003cp\u003eA screw compressor delivers warm, wet air, so plan the downstream side with it. Leave clearance on the cooling air side, run the unit on its own circuit sized to the motor nameplate, and add a \u003ca href=\"\/products\/abac-cool-25-refrigerated-air-dryer-115v\"\u003eCOOL 25 refrigerated air dryer\u003c\/a\u003e and a filter regulator if the air goes to paint, tires or anything that hates water. The COOL 25 treats 25 CFM and is rated to 232 PSI, so it covers this machine with margin on both counts. The AS-5501TMD above is the same compressor with that dryer already integrated, which saves the floor space and the interconnecting pipe. Oil, oil filter and separator element are the service items, so keep a spare set on the shelf and let the digital controller track the hours.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. The tank mount build is the simplest way into screw air: receiver and compressor ship as one unit on a single footprint, and a dryer can be added downstream at any time. See the full \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressor\u003c\/a\u003e range, all \u003ca href=\"\/collections\/5-hp-air-compressors\"\u003e5 HP air compressors\u003c\/a\u003e, or our \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at 138 PSI for 150 PSI maximum units. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54709062762771,"sku":"4152044120","price":6184.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54709062795539,"sku":"4152043890","price":6184.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-tank-mount-rotary-screw-air-compressor_ba383961-367a-414c-bec5-5efb6a7491f1.png?v=1790946147"},{"product_id":"abac-as-5-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor","title":"ABAC AS-5251TMD 5 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount with Dryer, 125 PSI, 20.3 CFM, 63 dBA","description":"\u003cp\u003eThe ABAC AS-5251TMD is a complete compressed air station on one skid: a 5 HP rotary screw air end, a 71 gallon air receiver and a refrigerated dryer, arriving mounted and plumbed as a single unit. This is the 125 PSI build, delivering 20.3 CFM and running at 63 dBA, quiet enough to sit in the work area instead of a separate compressor room. There is no separate tank or dryer to source, site and pipe, and nothing to size against each other after the fact. Choose 230V single-phase (AS-5251TMD) or 208-230-460V three-phase (AS-5253TMD); both are the same machine.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AS-5251TMD (230V single-phase) and AS-5253TMD (208-230-460V three-phase)\u003c\/li\u003e\n\u003cli\u003eMotor: 5 HP\u003c\/li\u003e\n\u003cli\u003eAir delivery: 20.3 CFM\u003c\/li\u003e\n\u003cli\u003eWorking pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 63 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 71 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 571 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 56 x 23 x 55 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eVertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a screw instead of a piston\u003c\/h3\u003e\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw runs, which is why shops that use air most of the day move to one. There is no duty cycle to watch, line pressure stays flat through a shift instead of sagging and recovering, and at 63 dBA this is the quietest machine in the AS-B range. The trade is that a screw dislikes short cycling, so it wants a receiver sized to its output and a demand pattern that keeps it loaded rather than starting and stopping all day. The 71 gallon tank on this build is matched to the air end for exactly that reason.\u003c\/p\u003e\u003ch3\u003eWhat the integrated dryer changes\u003c\/h3\u003e\u003cp\u003eEvery compressor makes water. Air leaves the air end hot and saturated, and as it cools in the receiver and the shop piping that moisture drops out as liquid, carrying into tools, regulators, pneumatic controls and anything being sprayed. The refrigerated dryer on this unit chills the air and condenses that water out before it reaches the distribution piping, so what leaves the skid is dry enough for paint work, tire service and air actuated equipment. On a bare compressor you would buy a dryer separately, find floor space beside it and pipe the two together; here it is already done and already matched to the output.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 5 HP AS-B builds the choice is pressure, tank and dryer. At 125 PSI this package puts out 20.3 CFM, the most flow of any 5 HP build in the range. If your tools or equipment need line pressure above the usual shop setting, the \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e150 PSI version of this same package\u003c\/a\u003e trades flow for pressure, 17.4 CFM instead of 20.3. If you already have dry air or do not need it, the \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003esame tank mount without the dryer\u003c\/a\u003e is the shorter machine at 485 lbs and the lower price. If you already own a receiver and want to keep it, the \u003ca href=\"\/products\/abac-as-5-5-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003e125 PSI base mount\u003c\/a\u003e is the same air end at 335 lbs with nothing under it. Stepping up, the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e7.5 HP tank mount with dryer\u003c\/a\u003e puts 30.5 CFM on the same 71 gallon tank at 67 dBA, which is the move when two people are on air at once.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003ePaint and finishing work, automotive service and tire bays, cabinet and woodworking shops, small production and fabrication floors, packaging and pneumatic control systems, and any operation where water in the air line is causing rejects, fisheyes or tool wear. The 125 PSI rating covers the great majority of shop air tools, which are rated at or below that pressure, and the 63 dBA sound level means the machine can live in the shop rather than in a closet.\u003c\/p\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eGive the cabinet clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. The dryer draws power alongside the compressor, so plan the circuit for the package rather than for the motor alone. Allow for the 56 x 23 x 55 in footprint plus service clearance, and remember that at 571 lbs this arrives on a pallet and wants a forklift or a pallet jack at delivery. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals for you. Add a filter regulator at each drop if the air feeds spray equipment. Call us with your own flow and duty cycle and we will check this machine against the demand before you pipe it in.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the Atlas Copco group. See the full \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressor\u003c\/a\u003e lineup, the \u003ca href=\"\/collections\/fixed-speed-rotary-screw-air-compressors\"\u003efixed speed screw compressors\u003c\/a\u003e, and our \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54709246460179,"sku":"4152044125","price":8607.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54709246492947,"sku":"4152043899","price":8607.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-71-gallon-tank-mount-dryer-rotary-screw-air-compressor.png?v=1790946107"},{"product_id":"abac-as-5-5-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor","title":"ABAC AS-5501TMD 5 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount with Dryer, 150 PSI, 17.4 CFM, 63 dBA","description":"\u003cp\u003eThe ABAC AS-5501TMD is a complete compressed air station on one skid: a 5 HP rotary screw air end, a 71 gallon air receiver and a refrigerated dryer, arriving mounted and plumbed as a single unit. This is the 150 PSI build, delivering 17.4 CFM and running at 63 dBA, quiet enough to sit in the work area instead of a separate compressor room. There is no separate tank or dryer to source, site and pipe, and nothing to size against each other after the fact. Choose 230V single-phase (AS-5501TMD) or 208-230-460V three-phase (AS-5503TMD); both are the same machine.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AS-5501TMD (230V single-phase) and AS-5503TMD (208-230-460V three-phase)\u003c\/li\u003e\n\u003cli\u003eMotor: 5 HP\u003c\/li\u003e\n\u003cli\u003eAir delivery: 17.4 CFM\u003c\/li\u003e\n\u003cli\u003eWorking pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 63 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 71 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 571 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 56 x 23 x 55 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eVertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a screw instead of a piston\u003c\/h3\u003e\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw runs, which is why shops that use air most of the day move to one. There is no duty cycle to watch, line pressure stays flat through a shift instead of sagging and recovering, and at 63 dBA this is the quietest machine in the AS-B range. The trade is that a screw dislikes short cycling, so it wants a receiver sized to its output and a demand pattern that keeps it loaded rather than starting and stopping all day. The 71 gallon tank on this build is matched to the air end for exactly that reason.\u003c\/p\u003e\u003ch3\u003eWhat the integrated dryer changes\u003c\/h3\u003e\u003cp\u003eEvery compressor makes water. Air leaves the air end hot and saturated, and as it cools in the receiver and the shop piping that moisture drops out as liquid, carrying into tools, regulators, pneumatic controls and anything being sprayed. The refrigerated dryer on this unit chills the air and condenses that water out before it reaches the distribution piping, so what leaves the skid is dry enough for paint work, tire service and air actuated equipment. On a bare compressor you would buy a dryer separately, find floor space beside it and pipe the two together; here it is already done and already matched to the output.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 5 HP AS-B builds the choice is pressure, tank and dryer. If your tools run at normal shop pressure, the \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e125 PSI version of this same package\u003c\/a\u003e trades the higher setting for more flow, 20.3 CFM instead of 17.4. If you already have dry air or do not need it, the \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003esame tank mount without the dryer\u003c\/a\u003e is the shorter machine and the lower price. If you already own a receiver and want to keep it, the \u003ca href=\"\/products\/abac-as-5-5-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003e150 PSI base mount\u003c\/a\u003e is the same air end at 335 lbs with nothing under it. Stepping up, the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e7.5 HP tank mount with dryer\u003c\/a\u003e puts 27.1 CFM on the same 71 gallon tank at 67 dBA, which is the move when two people are on air at once.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003ePaint and finishing work, automotive service and tire bays, cabinet and woodworking shops, small production and fabrication floors, packaging and pneumatic control systems, and any operation where water in the air line is causing rejects, fisheyes or tool wear. The 150 PSI rating suits shops running tools or equipment that need line pressure above the usual 125 PSI, and the 63 dBA sound level means it can live in the shop rather than in a closet.\u003c\/p\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eGive the cabinet clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. The dryer draws power alongside the compressor, so plan the circuit for the package rather than for the motor alone. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals for you. Add a filter regulator at each drop if the air feeds spray equipment. Call us with your own flow and duty cycle and we will check this machine against the demand before you pipe it in.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the Atlas Copco group. See the full \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressor\u003c\/a\u003e lineup, the \u003ca href=\"\/collections\/fixed-speed-rotary-screw-air-compressors\"\u003efixed speed screw compressors\u003c\/a\u003e, and our \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54709830123795,"sku":"4152044126","price":8607.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54709830156563,"sku":"4152043900","price":8607.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-71-gallon-tank-mount-dryer-rotary-screw-air-compressor_f62b8937-eb40-4f0e-8db4-c3abdf17d788.png?v=1790946156"},{"product_id":"abac-as-7-5-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor","title":"ABAC AS-7.5251TM7 7.5 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount, 125 PSI, 30.5 CFM, 67 dBA","description":"\u003cp\u003eThe ABAC AS-7.5251TM7 is the 7.5 HP AS-B rotary screw delivered as a finished package: the compressor, the controller and a 71 gallon ASME air receiver on one skid, wired and plumbed, so installation is a power drop and a line out. It makes 30.5 CFM at a 125 PSI maximum and runs at 67 dBA, quiet enough to live in the work area rather than a separate compressor room. A rotary screw is rated for continuous duty, so unlike a piston machine it does not need to rest between jobs, and the 71 gallon receiver is there to smooth demand rather than to be the air supply. Choose 230V single-phase (AS-7.5251TM, part 4152044121) or 208-230-460V three-phase (AS-7.5253TM, part 4152043891).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AS-7.5251TM \/ AS-7.5253TM (store reference AS-7.5251TM7)\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP, direct drive to an integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eAir delivery: 30.5 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 67 dBA\u003c\/li\u003e\n\u003cli\u003eReceiver: 71 gallon tank mount\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 507 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 63 x 23 x 57 in\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDuty cycle: 100 percent, continuous running\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at 109 PSI for 125 PSI maximum units. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eInside the AS-B 7.5 HP range the air end is the same and the configuration is what changes. The \u003ca href=\"\/products\/abac-as-7-5-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003ebase mount AS-7.5251BM\u003c\/a\u003e is the same compressor with no tank at 360 lbs and 32 x 24 x 40 in, for shops that already own a receiver. Step up to the \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003elarger tank mount\u003c\/a\u003e at 655 lbs if demand is spiky and you want more stored air. The \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251TMD7 with integrated dryer\u003c\/a\u003e adds refrigerated drying on the same 71 gallon footprint at 593 lbs. Pressure is the other axis: the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003e150 PSI build\u003c\/a\u003e of this same machine trades flow for line pressure, 27.1 CFM instead of 30.5 CFM. If 30.5 CFM is already tight, the \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003e10 HP AS-10253TM7\u003c\/a\u003e gives 36.4 CFM on the same 71 gallon platform.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eAutomotive service and tire bays running impacts and lifts all day, small fabrication and welding shops, cabinet and woodworking shops running sanders and nailers, auto body and finishing work, and any operation where a piston compressor is cycling hard enough to overheat or to keep the shop loud. At 30.5 CFM this machine comfortably covers two or three technicians on intermittent tools, a single sander or orbital, or a small plasma cutter. Sandblasting and multiple simultaneous impact wrenches want more air; size up from the \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw range\u003c\/a\u003e for that work.\u003c\/p\u003e\u003ch3\u003eInstallation and air treatment\u003c\/h3\u003e\u003cp\u003eLeave roughly 3 feet of clearance on the cooling air side, keep the room between 40 and 104 F, and run the unit on a dedicated circuit sized to the motor nameplate. Oil, oil filter and separator element are the scheduled service items and the controller tracks the intervals for you. A screw compressor discharges warm, saturated air, so if that air reaches paint, tires, pneumatic controls or anything that dislikes moisture, pair this unit with a dryer sized above its output: the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35 refrigerated dryer\u003c\/a\u003e at 35 CFM covers 30.5 CFM with headroom, and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer range\u003c\/a\u003e runs from 15 to 250 CFM.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the Atlas Copco group. Browse the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e or the wider range of \u003ca href=\"\/collections\/air-compressors\"\u003estationary air compressors\u003c\/a\u003e.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54710735339795,"sku":"4152044121","price":7051.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54710735372563,"sku":"4152043891","price":7055.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as75-71gal-tank-mount-150-psi-rotary-screw-air-compressor_4582b096-d7e2-4dcc-ac33-d2f9d636a960.png?v=1789761407"},{"product_id":"abac-as-7-5-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor","title":"ABAC AS-7.5501TM7 7.5 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount, 150 PSI, 27.1 CFM, 67 dBA","description":"\u003cp\u003eThe ABAC AS-7.5501TM7 is a 7.5 HP rotary screw air compressor shipped already mounted on a 71 gallon air receiver, so it lands as one package with no separate tank to source or plumb. It delivers 27.1 CFM at a 150 PSI maximum and runs at 67 dBA, quiet enough to sit in the work area instead of a separate compressor room. A screw compressor is built for continuous duty, so unlike a piston machine it holds line pressure through a full shift rather than recovering between jobs. Choose 230V single-phase (AS-7.5501TM7, part 4152044122) or 208-230-460V three-phase (AS-7.5503TM7, part 4152043892).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AS-7.5501TM7 (230V 1-phase) \/ AS-7.5503TM7 (208-230-460V 3-phase)\u003c\/li\u003e\n\u003cli\u003ePart numbers: 4152044122 \/ 4152043892\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP\u003c\/li\u003e\n\u003cli\u003eAir delivery: 27.1 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 67 dBA\u003c\/li\u003e\n\u003cli\u003eReceiver: 71 gallon, compressor tank mounted\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 507 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 63 x 23 x 57 in (L x W x H)\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eVertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the AS-B 7.5 HP family the decision comes down to pressure, receiver size and whether air treatment is in the package. The \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003e125 PSI build on the same 71 gallon tank\u003c\/a\u003e delivers 30.5 CFM instead of 27.1, so take this 150 PSI version when line pressure rather than raw volume is the constraint, for instance a long pipe run or equipment that specifies more than a standard 125 PSI supply. The \u003ca href=\"\/products\/abac-as-7-5-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003ebase mount\u003c\/a\u003e is the same compressor without a tank at 360 lbs and a 32 x 24 x 40 in footprint, for shops that already own a receiver. The \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003e131 gallon tank mount\u003c\/a\u003e carries a larger receiver for longer run and rest cycles, and the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e71 gallon tank mount with dryer\u003c\/a\u003e adds an integrated refrigerated dryer so compressor, receiver and air treatment arrive as a single 3-in-1 unit.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eAutomotive service bays, tire shops, small production and fabrication floors, cabinet and woodworking shops, and any operation where a piston compressor is cycling too hard to keep up. The 150 PSI rating adds headroom over the 125 PSI build when equipment downstream calls for a higher line pressure, or when a long run of pipe eats into pressure at the point of use. The 71 gallon receiver keeps the machine from short cycling on intermittent demand, which is the quickest way to shorten the life of any screw compressor.\u003c\/p\u003e\u003ch3\u003eInstallation and service\u003c\/h3\u003e\u003cp\u003eLeave clearance on the cooling air side so the unit can move air freely, keep the room ventilated and above freezing, and run the compressor on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the routine service items, and the digital controller tracks the intervals for you. If the air feeds paint, tires, instrumentation or anything else that will not tolerate moisture, add a \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e and filtration downstream, or step across to the tank mount with dryer build.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. See the full range of \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e, or browse \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e if you are specifying air treatment at the same time.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at 138 PSI for 150 PSI maximum units. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54710893805843,"sku":"4152044122","price":7051.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54710893838611,"sku":"4152043892","price":7055.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as75-71gal-tank-mount-150-psi-rotary-screw-air-compressor.png?v=1789441592"},{"product_id":"abac-as-7-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor","title":"ABAC AS-7.5251TMD7 7.5 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount with Dryer, 125 PSI, 30.5 CFM, 67 dBA","description":"\u003cp\u003eThe ABAC AS-7.5251TMD7 is a complete compressed air station on one base: a 7.5 HP rotary screw compressor, a 71 gallon air receiver and an integrated refrigerated dryer, mounted and plumbed together at the factory. It delivers 30.5 CFM at 125 PSI and runs at 67 dBA, quiet enough to sit in the work area rather than in a separate compressor room. At 60 x 23 x 57 in it is the compact way to put clean, dry shop air on one footprint, so installation comes down to setting it in place, wiring it and connecting the air line. Choose 230V single-phase (AS-7.5251TMD7) or 208-230-460V three-phase (AS-7.5253TMD7).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AS-7.5251TMD7 (part number 4152044127) and AS-7.5253TMD7 (part number 4152043901)\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 30.5 CFM\u003c\/li\u003e\n\u003cli\u003eWorking pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 67 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 71 gallon air receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer\u003c\/li\u003e\n\u003cli\u003eCompressor, receiver and dryer on a single base\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eDimensions: 60 x 23 x 57 in\u003c\/li\u003e\n\u003cli\u003eWeight: 593 lbs\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eThree stage vertical oil separation, oil carryover under 5 ppm across the AS screw range\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a screw instead of a piston\u003c\/h3\u003e\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw runs, which is why shops that use air most of the day move to one. There is no duty cycle to watch, line pressure stays flat through a shift instead of sagging and recovering, and ABAC rates a comparable piston machine as much as 20 dBA louder than a screw. The trade is that a screw dislikes short cycling, so it wants a receiver sized to its output and a demand pattern that keeps it loaded rather than starting and stopping all day. On this build the 71 gallon receiver is already matched to the air end, so that sizing decision is made for you.\u003c\/p\u003e\u003ch3\u003eWhat is inside\u003c\/h3\u003e\u003cp\u003eThe AS-B range is built around a fully integrated aluminum block air end, which keeps the rotors, bearings and oil circuit in one casting rather than a bolted assembly, and ABAC pairs it with an eco friendly three stage vertical oil separation process. Vertical separation reduces the risk of condensation building up and corroding the separator circuit, and it holds oil carryover under 5 ppm, so what reaches your tools and your finish is cleaner than a piston machine will deliver. The energy efficient motor and the compact cabinet limit air loss and standby losses, and the digital controller gives menu driven operation, programmed maintenance intervals and running hours at a glance rather than a pressure switch and a guess.\u003c\/p\u003e\u003ch3\u003eWhat the integrated dryer buys you\u003c\/h3\u003e\u003cp\u003eAir leaving any compressor is warm and saturated. As it cools in the piping that moisture drops out as liquid water, and it ends up in the tool, the finish, the cylinder or the control valve at the far end of the run. A refrigerated dryer chills the air at the compressor so the water condenses and drains there instead of travelling down the line. Buying it integrated rather than as a separate box means one electrical connection, one footprint, no interconnecting pipework to get wrong, and a dryer already matched to this compressor's output rather than guessed at. For paint and finishing work, pneumatic controls, plasma tables and tire service, drying at the source is the difference between a system that works and one that is always being chased with traps and filters.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the AS-B 7.5 HP range the differences come down to storage, air treatment and pressure. The \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e131 gallon tank mount with dryer\u003c\/a\u003e is the same compressor and dryer on a larger receiver at 741 lbs and a 76 in long footprint, which is the better buy if several bays pull at once or the floor space is there. Drop the dryer and the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003e71 gallon tank mount\u003c\/a\u003e comes down to 507 lbs for a shop that already has air treatment downstream. The \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e150 PSI version of this machine\u003c\/a\u003e trades air delivery for pressure at 27.1 CFM, so choose on whether your tools are short of volume or short of pressure. Shops replacing a compressor on existing piping can take the \u003ca href=\"\/products\/abac-as-7-5-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003ebase mount build\u003c\/a\u003e at 360 lbs on a 32 x 24 x 40 in footprint. If demand is already outrunning 30 CFM, the \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e10 HP AS-10253TMD7\u003c\/a\u003e steps the same package up to 36.4 CFM, and the \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e5 HP AS-5251TMD\u003c\/a\u003e covers a lighter shop at 20.3 CFM.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eABAC builds the AS-B range for professional and industrial work where the air supply has to be continuous and the operating conditions are hard on equipment: heavy assembly, production line assembly, and cleaning and preparation work. In practice that usually looks like automotive and fleet service bays, tire shops, cabinet and woodworking shops, paint and finishing lines, and small production floors where moisture in the air line causes rejects or shortens tool life. Drying the air at the compressor keeps condensate out of the distribution piping instead of leaving it for traps and filters downstream to catch.\u003c\/p\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eGive the cabinet clear air on the cooling side, keep it out of a hot corner, and leave working room at the service panels. The unit measures 60 x 23 x 57 in and weighs 593 lbs, so plan the route in and the pad it sits on before it arrives. Run it on its own circuit sized to the motor nameplate, and confirm the supply matches the version you order, because the single-phase and three-phase builds are different part numbers. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals for you. Call us with your own flow and duty cycle and we will check this machine against the demand before you pipe it in.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the \u003ca href=\"\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e, the \u003ca href=\"\/collections\/fixed-speed-rotary-screw-air-compressors\"\u003efixed speed screw compressors\u003c\/a\u003e, and our \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e if you are treating air for an existing machine.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C at 109 PSI for 125 PSI max units. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54719223726355,"sku":"4152044127","price":9379.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54719223759123,"sku":"4152043901","price":9348.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-71-gallon-tank-mount-dryer-rotary-screw-air-compressor_aaa8ef11-6d4c-4395-9657-b5c9de12b35a.png?v=1790946156"},{"product_id":"abac-as-7-5-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor","title":"ABAC AS-7.5501TMD7 7.5 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount with Dryer, 150 PSI, 27.1 CFM, 67 dBA","description":"\u003cp\u003eThe ABAC AS-7.5501TMD7 is a complete compressed air station in one package: a 7.5 HP rotary screw compressor, a 71 gallon air receiver and a refrigerated dryer, mounted and plumbed as a single factory assembly. It delivers 27.1 CFM at 150 PSI and runs at 67 dBA, quiet enough to sit in the work area instead of a separate compressor room. The whole station weighs 593 lbs and stands on a 60 x 23 in footprint, so it occupies one position against a shop wall where a compressor, a receiver and a standalone dryer would need three. Choose 230V single-phase (AS-7.5501TMD7) or 208-230-460V three-phase (AS-7.5503TMD7).\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModels: AS-7.5501TMD7 (part number 4152044128) and AS-7.5503TMD7 (part number 4152043902)\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 27.1 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 67 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 71 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 593 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 60 x 23 x 57 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy the three in one package\u003c\/h3\u003e\n\u003cp\u003eA rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs the way a piston machine does. The catch is that air leaving any screw comes out hot and saturated, so a dryer is not optional on a system feeding paint, pneumatic controls or precision tools. Buying the compressor, the receiver and the refrigerated dryer as one factory assembly removes the part of the job that usually goes wrong: no separate dryer to size and source, no interconnecting pipe to fabricate, no second set of mounts, and no chance of a dryer undersized for the air end in front of it. The installer lands power and ties into the header. The 71 gallon receiver underneath keeps the screw from short cycling, which is the one duty pattern a screw genuinely dislikes.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eOn identical hardware, pressure and airflow trade directly against each other, and this machine sits at the pressure end of that trade. The \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251TMD7\u003c\/a\u003e is the same 593 lb package set for 125 PSI at 30.5 CFM, so stepping from 125 to 150 PSI costs about 3.4 CFM on the same 7.5 HP motor. Buy pressure only to the level your highest tool actually needs. If drying is already handled elsewhere in the shop, the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-7.5501TM7\u003c\/a\u003e is this same 71 gallon build without the dryer at 507 lbs, and the \u003ca href=\"\/products\/abac-as-7-5-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-7.5501BM\u003c\/a\u003e is the bare base mount at 360 lbs on a 32 x 24 in footprint for a shop that already owns a receiver. For longer runs between stops, the \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-7.5501TMD\u003c\/a\u003e puts the same 27.1 CFM on a larger receiver at 741 lbs and a 76 x 24 in footprint. Below this machine the \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-5501TMD\u003c\/a\u003e holds 150 PSI at 17.4 CFM, and above it the three-phase \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TMD7\u003c\/a\u003e reaches 34.1 CFM on the same 71 gallon footprint at 653 lbs.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003ePaint and finishing work, automotive service bays, tire shops, cabinet and woodworking shops, and small production floors where moisture in the air line causes rejects or tool wear. The 150 PSI rating suits shops running impact tooling, clamping fixtures or equipment that calls for more line pressure than a 125 PSI station can hold, and it leaves headroom for a long pipe drop without the pressure at the far end falling below what the tool is rated for. The integrated dryer removes water before it reaches the distribution piping, which matters anywhere air touches a finish, a pneumatic control or a precision tool. At 67 dBA the machine can sit in the work area rather than in a dedicated compressor room, which is often what decides the package over a bare base mount machine.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Confirm your piping, fittings and hose are rated above 150 PSI before you commission it. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals, so keep a spare set on the shelf. The refrigerated dryer is already fitted, so the remaining air treatment decision is filtration: a particulate and coalescing filter set behind the dryer protects tools and finishes from pipe scale and oil carryover. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the wider \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eUnit performance measured according to ISO 1217 Annex C, with CFM quoted at 138 PSI for 150 PSI maximum units. Noise level measured according to ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54719365841171,"sku":"4152044128","price":9379.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54719370723603,"sku":"4152043902","price":9348.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-71-gallon-tank-mount-dryer-rotary-screw-air-compressor_013e2b51-f5fb-4a77-bb27-dd8da3480ca9.png?v=1790946157"},{"product_id":"abac-as-10-10-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor","title":"ABAC AS-10253TM7 10 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount, 125 PSI, 36.4 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-10253TM7 is the 71 gallon tank mount build of the 10 HP machine in the AS-B screw range. It delivers 36.4 CFM with a 125 PSI maximum and runs at 69 dBA, quiet enough to sit in the work area instead of a separate compressor room. The air end and the receiver arrive as one assembled package, so there is no separate tank to source, set and plumb, and the whole unit lands on a 60 x 23 in footprint. At 567 lbs it is the compact receiver option in the 10 HP family, the one to buy when floor space is tight but you still want stored air. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10253TM7 (part number 4152043895)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 36.4 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 71 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 567 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 60 x 23 x 57 in\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access for optimizing operating performance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops using air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end limits air loss by design, and ABAC pairs it with an energy efficient motor and a digital controller, so the operating menus and the service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 71 gallon receiver underneath it is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow, receiver size and mounting all move independently. The \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TM7\u003c\/a\u003e is the same package set for 150 PSI, trading airflow down to 34.1 CFM for the extra pressure. If demand is intermittent and you want the pump to rest longer between loads, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003e131 gallon tank mount\u003c\/a\u003e carries the same 36.4 CFM on a larger receiver at 714 lbs. The \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TMD7\u003c\/a\u003e is this same 71 gallon build with a refrigerated dryer already integrated, which saves plumbing a separate dryer in. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-10-10-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253BM\u003c\/a\u003e is the bare 419 lb base mount. Stepping down, the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251TM7\u003c\/a\u003e gives 30.5 CFM at 67 dBA on the same 71 gallon tank; stepping up, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TM\u003c\/a\u003e carries 52.1 CFM. If noise is the deciding factor, the \u003ca href=\"\/products\/abac-as-10s-10-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253BM\u003c\/a\u003e is the quieter 10 HP air end at 65 dBA and 39.8 CFM.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, larger automotive and fleet service shops, tire and truck bays, cabinet and woodworking shops, plasma tables and packaging lines. At 36.4 CFM it will keep several air ratchets, an orbital sander or a continuous blow off fed through a shift without the line pressure sagging. The tank mount build is the one to buy for a shop that is starting its compressed air system from nothing, because the receiver, the mounts and the interconnecting pipe are already done and the installer only has to land power and tie into the header.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals. Air leaving any screw carries moisture, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 36.4 CFM the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eABAC COOL 50\u003c\/a\u003e is the sensible match and runs on 115V, so it plugs in beside the compressor without new wiring; step to the \u003ca href=\"\/products\/abac-cool-65-refrigerated-air-dryer-115v\"\u003eCOOL 65\u003c\/a\u003e if the room runs hot or the air feeds finishing work. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at 109 PSI for 125 PSI maximum units. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":54746271711507,"sku":"4152043895","price":7604.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as75-71gal-tank-mount-150-psi-rotary-screw-air-compressor_945e2bc2-4f99-4c70-bb40-0ea71e0d7392.png?v=1789780199"},{"product_id":"abac-as-10-10-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor","title":"ABAC AS-10503TM7 10 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount, 150 PSI, 34.1 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-10503TM7 is the 150 PSI, 71 gallon tank mount build of the 10 HP machine in the AS-B screw range. It delivers 34.1 CFM at a 150 PSI maximum and runs at 69 dBA, quiet enough to sit in the work area instead of a separate compressor room. The higher pressure setting is the one to specify when a tool, a clamp circuit or a plant header needs more than the usual 125 PSI, or when a long pipe run eats pressure before the air reaches the point of use. The air end and the receiver arrive as one assembled package on a 60 x 23 in footprint, so there is no separate tank to source, set and plumb. At 567 lbs it is the compact receiver option in the 10 HP family, the one to buy when floor space is tight but you still want stored air. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10503TM7 (part number 4152043896)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 34.1 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 71 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 567 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 60 x 23 x 57 in\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access for optimizing operating performance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops using air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end limits air loss by design, and ABAC pairs it with an energy efficient motor and a digital controller, so the operating menus and the service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 71 gallon receiver underneath it is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow, receiver size and mounting all move independently. The \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TM7\u003c\/a\u003e is the identical 567 lb package set for 125 PSI, trading the extra pressure for more airflow at 36.4 CFM. If demand is intermittent and you want the pump to rest longer between loads, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TM\u003c\/a\u003e carries the same 34.1 CFM on a larger receiver. The \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TMD7\u003c\/a\u003e is this same 71 gallon build with a refrigerated dryer already integrated, which saves plumbing a separate dryer in. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-10-10-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503BM\u003c\/a\u003e is the bare 419 lb base mount at the same pressure. Stepping down, the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-7.5501TM7\u003c\/a\u003e gives 27.1 CFM at 67 dBA on the same 71 gallon tank; stepping up, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TM\u003c\/a\u003e carries 46.4 CFM. If noise is the deciding factor, the \u003ca href=\"\/products\/abac-as-10s-10-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503BM\u003c\/a\u003e is the quieter 10 HP air end at 65 dBA and 35.6 CFM on the same 150 PSI setting. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, larger automotive and fleet service shops, tire and truck bays, cabinet and woodworking shops, plasma and laser tables, packaging lines, and any operation running tooling or a test rig specified above 125 PSI. At 34.1 CFM it will keep several air ratchets, an orbital sander or a continuous blow off fed through a shift without the line pressure sagging. The tank mount build is the one to buy for a shop starting its compressed air system from nothing, because the receiver, the mounts and the interconnecting pipe are already done and the installer only has to land power and tie into the header.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals. Air leaving any screw carries moisture, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 34.1 CFM the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eABAC COOL 50\u003c\/a\u003e gives useful headroom and runs on 115V, so it plugs in beside the compressor without new wiring; the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eCOOL 35\u003c\/a\u003e is the minimum size. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":54746489651475,"sku":"4152043896","price":7604.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as75-71gal-tank-mount-150-psi-rotary-screw-air-compressor_61607108-6bc3-43fb-9457-5950c94c3241.png?v=1790869039"},{"product_id":"abac-as-10-10-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor","title":"ABAC AS-10253TMD7 10 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount with Dryer, 125 PSI, 36.4 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-10253TMD7 is the 125 PSI, 71 gallon build of the 10 HP machine in the AS-B screw range, and it arrives as a complete air station: compressor, receiver and refrigerated dryer mounted and plumbed as one unit. It delivers 36.4 CFM and runs at 69 dBA, quiet enough to sit in the work area instead of a separate compressor room. At 653 lbs on a 60 x 27 in footprint it is the compact receiver option in the 10 HP family, the one to specify when floor space is tight but the air still has to be dry. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10253TMD7 (part number 4152043905)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 36.4 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 71 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 653 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 60 x 27 x 57 in\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is why shops running air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end is designed to limit air loss, and ABAC pairs it with an energy efficient motor and a digital controller, so operating menus and service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 71 gallon receiver underneath it is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eWhy the dryer is integrated\u003c\/h3\u003e\n\u003cp\u003eAir leaving any compressor is warm and saturated, and it drops that water out in the pipe run where it reaches tools, cylinders and finishes. Buying the dryer already mounted and plumbed removes a separate purchase, a separate footprint and the fittings between the two. It also means the dryer is correctly sized to this machine's 36.4 CFM from the start, which is the step most often got wrong when a dryer is added later. If you prefer to keep the dryer separate, pair the plain tank mount with a standalone unit from our \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow, receiver size and dryer all move independently. The \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TM7\u003c\/a\u003e is the same 71 gallon package without the dryer, 86 lbs lighter at 567 lbs and 4 in narrower. The \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TMD7\u003c\/a\u003e is this identical 653 lb machine set for 150 PSI, trading airflow down to 34.1 CFM for the extra pressure. If demand is intermittent and you want the pump to rest longer between loads, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TMD\u003c\/a\u003e carries the same 36.4 CFM and dryer on a larger receiver. If you already own a tank and a dryer, the \u003ca href=\"\/products\/abac-as-10-10-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253BM\u003c\/a\u003e is the bare 419 lb base mount at the same pressure. Stepping down, the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251TMD7\u003c\/a\u003e gives 30.5 CFM at 67 dBA on the same 71 gallon tank. If noise is the deciding factor, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253TMD\u003c\/a\u003e is the quieter 10 HP air end at 65 dBA and 39.8 CFM. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003ePaint and finishing work, production and fabrication floors, larger automotive and fleet service bays, tire and truck shops, plasma and laser tables, and cabinet and woodworking shops where moisture in the air line causes rejects or tool wear. The integrated dryer removes water before it reaches the distribution piping, which matters anywhere air touches a finish, a pneumatic control or a precision tool. Allow clearance on the cooling air side, keep the room between roughly 40 and 104 F, and run the machine on its own circuit sized to the motor nameplate.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at 109 PSI for 125 PSI maximum units. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the Atlas Copco group. See the full \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressor\u003c\/a\u003e lineup.\u003c\/p\u003e\n","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":54747589345555,"sku":"4152043905","price":8704.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as10-71gal-tank-mount-dryer-125-psi-rotary-screw-air-compressor.png?v=1789794353"},{"product_id":"abac-as-10-10-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor","title":"ABAC AS-10503TMD7 10 HP Rotary Screw Air Compressor - 71 Gallon Tank Mount with Dryer, 150 PSI, 34.1 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-10503TMD7 is a complete compressed air station in one package. It delivers 34.1 CFM at 150 PSI and runs at 69 dBA, quiet enough to sit in the work area instead of a separate compressor room. Compressor, 71 gallon air receiver and refrigerated dryer arrive mounted and plumbed as a single factory assembly, so there is no separate tank or dryer to source, site and pipe. Installation comes down to setting it in place, landing power and tying into the header. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10503TMD7 (part number 4152043906)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP\u003c\/li\u003e\n\u003cli\u003eAir delivery: 34.1 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 71 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 653 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 60 x 27 x 57 in\u003c\/li\u003e\n\u003cli\u003eIntegrated air end block of aluminum construction\u003c\/li\u003e\n\u003cli\u003eVertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance intervals\u003c\/li\u003e\n\u003cli\u003eRated for 100 percent continuous duty\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy the three in one package\u003c\/h3\u003e\n\u003cp\u003eA rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs the way a piston machine does. The catch is that air leaving any screw comes out hot and saturated, so a dryer is not optional on a system feeding paint, pneumatic controls or precision tools. Buying the compressor, the receiver and the refrigerated dryer as one factory assembly removes the part of the job that usually goes wrong: no separate dryer to size and source, no interconnecting pipe to fabricate, no second set of mounts, and no chance of a dryer undersized for the air end in front of it. The 71 gallon receiver underneath keeps the screw from short cycling, which is the one duty pattern a screw genuinely dislikes.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eWithin the AS-B tank mount with dryer builds the choice is flow against line pressure, then storage. The \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e125 PSI version of this same package\u003c\/a\u003e gives 36.4 CFM on an identical 653 lb, 60 x 27 x 57 in footprint, so if your tools run happily at 125 PSI you gain about 2 CFM for nothing. Step down a size and the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e7.5 HP 150 PSI build\u003c\/a\u003e delivers 27.1 CFM at 67 dBA. Step up in storage and the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e131 gallon version\u003c\/a\u003e carries the same 10 HP air end on a larger receiver at 800 lbs and a 76 x 24 x 63 in footprint, which suits shops that draw in heavy bursts. For a quieter machine with more air on the same 10 HP, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503TMD\u003c\/a\u003e uses the 10S air end for 35.6 CFM at 65 dBA, and if 34.1 CFM is short of what the shop actually draws, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TMD\u003c\/a\u003e holds 150 PSI at 46.4 CFM. If the shop already has drying handled, the \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TM7\u003c\/a\u003e is this same 71 gallon build without the dryer, and the \u003ca href=\"\/products\/abac-as-10-10-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003ebase mount AS-10503BM\u003c\/a\u003e is the compressor on its own for a plant that already owns a receiver.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003ePaint and finishing work, production and fabrication floors, larger automotive and fleet service bays, tire and truck shops, and cabinet and woodworking shops where moisture in the air line causes rejects or tool wear. The integrated dryer removes water before it reaches the distribution piping, which matters anywhere air touches a finish, a pneumatic control or a precision tool. The 150 PSI rating suits shops running tools or equipment rated above the common 125 PSI setting, where a press, a clamping fixture or a truck tire bead seater wants more than a 125 PSI header will give after line losses. At 60 x 27 x 57 in the whole station fits against a wall rather than needing a dedicated room, and at 653 lbs it is the lighter of the two 10 HP dryer packages to rig into place.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals, so keep a spare set on the shelf. The refrigerated dryer is already fitted, so the remaining air treatment decision is filtration: a particulate and coalescing filter set behind the dryer protects tools and finishes from pipe scale and oil carryover. Because the 71 gallon receiver is on the smaller side for 34.1 CFM, a shop with heavy intermittent draws such as impact tools, blow off stations or cabinet blasting should either add a secondary receiver downstream or specify the 131 gallon build instead.\u003c\/p\u003e\n\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eUnit performance measured according to ISO 1217 Annex C. Noise level measured according to ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":54748071919891,"sku":"4152043906","price":8704.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as10-71gal-tank-mount-dryer-150-psi-rotary-screw-air-compressor.png?v=1789797956"}],"url":"https:\/\/aircompressorstore.com\/collections\/abac-71-gallon-air-compressors.oembed","provider":"Warthog Air Compressor Store","version":"1.0","type":"link"}