{"title":"ABAC 131 Gallon Rotary Screw Air Compressors","description":"\u003ch2\u003eABAC 131 Gallon Rotary Screw Air Compressors\u003c\/h2\u003e\n\u003cp\u003eA 131 gallon receiver is the tank ABAC mounts its AS series screws on when the machine is meant to arrive as one piece. Air end, motor, controller and tank ship bolted together, so the install is a power feed and a line out rather than a slab, a separate receiver and a day of pipe work. Every machine on this page is an AS rotary screw on that 131 gallon tank, from 7.5 HP at 27.1 CFM up to 30 HP at 114.1 CFM.\u003c\/p\u003e\n\u003cp\u003ePressure is the next choice, and it trades directly against airflow on the same frame. Twelve of these run 125 PSI, twelve run 150 PSI and six run 175 PSI. The 15 HP machine shows the pattern: 52.1 CFM at 125 PSI, 46.4 CFM at 150 PSI and 41.7 CFM at 175 PSI. Buy the lowest pressure that still carries the tools at the drop, because every 25 PSI of headroom costs real CFM and real power. Noise runs 65 to 71 dBA across the range, with the quieter 10S air ends at 65 dBA.\u003c\/p\u003e\n\u003cp\u003eSeventeen of the thirty arrive with an integrated refrigerated dryer built into the package, including every 25 and 30 HP machine here, which is the simplest way to keep water out of the lines when the air goes to paint, plasma or pneumatic controls. If the shop already owns a receiver, the same air ends are sold bare on \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-base-mount-rotary-screw-air-compressors\"\u003ebase mount\u003c\/a\u003e frames. See every tank mounted build in \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-tank-mount-rotary-screw-air-compressors\"\u003eABAC tank mount rotary screws\u003c\/a\u003e, the dryer equipped machines in \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-rotary-screw-air-compressors-with-dryer\"\u003erotary screws with integrated dryer\u003c\/a\u003e, the full screw range in \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-rotary-screw-air-compressors\"\u003eABAC AS rotary screw air compressors\u003c\/a\u003e, and the whole brand in \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-air-compressors\"\u003eABAC air compressors\u003c\/a\u003e. For intermittent rather than continuous air draw, compare the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/abac-120-gallon-air-compressors\"\u003eABAC 120 gallon piston machines\u003c\/a\u003e instead.\u003c\/p\u003e","products":[{"product_id":"abac-as-7-5-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor","title":"ABAC AS-7.5251TM 7.5 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 125 PSI, 30.5 CFM, 67 dBA","description":"\u003cp\u003eThe ABAC AS-7.5251TM is the 125 PSI, 131 gallon tank mount build of the 7.5 HP machine in the AS-B screw range. It delivers 30.5 CFM at a 125 PSI maximum and runs at 67 dBA, quiet enough to sit in the work area instead of a separate compressor room. This is the higher airflow setting offered on the 7.5 HP air end, so it is the one to specify when the shop is short of air rather than short of pressure. The air end and the receiver arrive as one assembled package on a 76 x 24 in footprint, so there is no separate tank to source, set and plumb. At 655 lbs it is the large receiver option in the 7.5 HP family, the one to buy when demand is intermittent and you want the compressor to run longer and rest longer rather than load and unload all day. Choose 230V single-phase (AS-7.5251TM) or 208-230-460V three-phase (AS-7.5253TM).\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModels: AS-7.5251TM (part number 4152044123) and AS-7.5253TM (part number 4152043893)\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 30.5 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 67 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 655 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 24 x 63 in\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access for optimizing operating performance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops using air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end limits air loss by design, and ABAC pairs it with an energy efficient motor and a digital controller, so the operating menus and the service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 131 gallon receiver underneath it is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow, receiver size and mounting all move independently. The \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-7.5501TM\u003c\/a\u003e is the identical 655 lb package set for 150 PSI, trading 3.4 CFM of airflow for the extra pressure. If floor space is the constraint, the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251TM7\u003c\/a\u003e carries the same 30.5 CFM on a 71 gallon receiver at 507 lbs and a 63 x 23 in footprint. The \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251TMD\u003c\/a\u003e is this same 131 gallon build with a refrigerated dryer already integrated at 741 lbs, which saves plumbing a separate dryer in. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-7-5-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251BM\u003c\/a\u003e is the bare 360 lb base mount at the same pressure and airflow. Stepping down, the \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-5251TM\u003c\/a\u003e gives 20.3 CFM at a quieter 63 dBA; stepping up, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TM\u003c\/a\u003e carries 36.4 CFM at 69 dBA on the same receiver. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eAutomotive and fleet service bays, tire and truck shops, small production and fabrication floors, cabinet and woodworking shops, plasma tables, packaging lines, and any operation where a piston compressor is cycling too hard to keep up. At 30.5 CFM it will keep a pair of air ratchets, an orbital sander or a continuous blow off fed through a shift without the line pressure sagging. The 131 gallon receiver stores well over twice the air of the 71 gallon build, which matters when several bays hit the header at once or when a single large tool draws a short, heavy burst. The tank mount build is the one to buy for a shop starting its compressed air system from nothing, because the receiver, the mounts and the interconnecting pipe are already done and the installer only has to land power and tie into the header.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals. Air leaving any screw carries moisture, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 30.5 CFM the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35\u003c\/a\u003e is the matching size and the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eCOOL 50\u003c\/a\u003e leaves headroom for a later expansion, and both run on 115V so they sit beside the compressor without new wiring. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at 109 PSI for 125 PSI maximum units. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54719053496595,"sku":"4152044123","price":7380.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54719053529363,"sku":"4152043893","price":7380.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-tank-mount-rotary-screw-air-compressor_f0271557-56be-4fa8-b4d8-595d216f0256.png?v=1790946147"},{"product_id":"abac-as-7-5-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor","title":"ABAC AS-7.5501TM 7.5 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 150 PSI, 27.1 CFM, 67 dBA","description":"\u003cp\u003eThe ABAC AS-7.5501TM is the 150 PSI, 131 gallon tank mount build of the 7.5 HP machine in the AS-B screw range. It delivers 27.1 CFM at a 150 PSI maximum and runs at 67 dBA, quiet enough to sit in the work area instead of a separate compressor room. This is the higher pressure setting offered on the 7.5 HP air end, so it is the one to specify when a tool or a process needs more than the 125 PSI a standard shop supply gives. The air end and the receiver arrive as one assembled package on a 76 x 24 in footprint, so there is no separate tank to source, set and plumb. At 655 lbs it is the large receiver option in the 7.5 HP family, the one to buy when demand is intermittent and you want the compressor to run longer and rest longer rather than load and unload all day. Choose 230V single-phase (AS-7.5501TM) or 208-230-460V three-phase (AS-7.5503TM).\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModels: AS-7.5501TM (part number 4152044124) and AS-7.5503TM (part number 4152043894)\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 27.1 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 67 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 655 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 24 x 63 in\u003c\/li\u003e\n\u003cli\u003eFully integrated air end block of aluminum construction\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access for operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops using air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end is designed to limit air loss, and ABAC pairs it with an energy efficient motor and a digital controller, so the operating menus and the service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 131 gallon receiver underneath it is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow, receiver size and mounting all move independently. The \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251TM\u003c\/a\u003e is the identical 655 lb package set for 125 PSI, which buys back 3.4 CFM of airflow if your tools are happy at the lower pressure. If floor space is the constraint, the \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-7.5501TM7\u003c\/a\u003e carries the same 27.1 CFM at 150 PSI on a 71 gallon receiver at 507 lbs and a 63 x 23 in footprint. The \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-7.5501TMD\u003c\/a\u003e is this same 131 gallon build with a refrigerated dryer already integrated at 741 lbs, which saves plumbing a separate dryer in. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-7-5-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-7.5501BM\u003c\/a\u003e is the bare 360 lb base mount at the same pressure and airflow on a 32 x 24 in footprint. Stepping down, the \u003ca href=\"\/products\/abac-as-5-5-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-5501TM\u003c\/a\u003e gives 17.4 CFM at a quieter 63 dBA; stepping up, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TM\u003c\/a\u003e carries 34.1 CFM at 69 dBA on the same receiver. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eAutomotive and fleet service bays, tire and truck shops, small production and fabrication floors, cabinet and woodworking shops, plasma tables, packaging lines, and any operation where a piston compressor is cycling too hard to keep up. The 150 PSI rating suits shops running impact tools, pneumatic presses or clamping equipment that need pressure above the common 125 PSI setting, and it leaves room for the pressure drop a long header and a filter set will cost you before the air reaches the tool. At 27.1 CFM it will keep a pair of air ratchets, an orbital sander or a continuous blow off fed through a shift without the line pressure sagging. The 131 gallon receiver stores well over twice the air of the 71 gallon build, which matters when several bays hit the header at once or when a single large tool draws a short, heavy burst.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals, so keep a spare set on the shelf. Air leaving any screw is hot and saturated, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 27.1 CFM the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eABAC COOL 35\u003c\/a\u003e is the matching size and the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eCOOL 50\u003c\/a\u003e leaves headroom for a later expansion, and both run on 115V so they sit beside the compressor without new wiring. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at 138 PSI for 150 PSI maximum units. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e\n","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54719099896083,"sku":"4152044124","price":7380.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54719099928851,"sku":"4152043894","price":7380.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-tank-mount-rotary-screw-air-compressor_5d485745-1b47-4406-a5f6-be334c1440df.png?v=1790946147"},{"product_id":"abac-as-7-5-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor","title":"ABAC AS-7.5251TMD 7.5 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 125 PSI, 30.5 CFM, 67 dBA","description":"\u003cp\u003eThe ABAC AS-7.5251TMD is a complete compressed air station on one base: a 7.5 HP rotary screw compressor, a 131 gallon air receiver and an integrated refrigerated dryer, mounted and plumbed together at the factory. It delivers 30.5 CFM at 125 PSI and runs at 67 dBA, quiet enough to sit in the work area rather than in a separate compressor room. There is no tank and no dryer to size, site and pipe, so installation comes down to setting it in place, wiring it and connecting the air line. Choose 230V single-phase (AS-7.5251TMD) or 208-230-460V three-phase (AS-7.5253TMD).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AS-7.5251TMD (part number 4152044129) and AS-7.5253TMD (part number 4152043903)\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 30.5 CFM\u003c\/li\u003e\n\u003cli\u003eWorking pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 67 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon air receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer\u003c\/li\u003e\n\u003cli\u003eCompressor, receiver and dryer on a single base\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eDimensions: 76 x 24 x 63 in\u003c\/li\u003e\n\u003cli\u003eWeight: 741 lbs\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end with vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a screw instead of a piston\u003c\/h3\u003e\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw runs, which is why shops that use air most of the day move to one. There is no duty cycle to watch, line pressure stays flat through a shift instead of sagging and recovering, and at 67 dBA the machine sits well below a comparable reciprocating unit. The trade is that a screw dislikes short cycling, so it wants a receiver sized to its output and a demand pattern that keeps it loaded rather than starting and stopping all day. On this build the 131 gallon receiver is already matched to the air end, so that sizing decision is made for you.\u003c\/p\u003e\u003ch3\u003eWhat the integrated dryer buys you\u003c\/h3\u003e\u003cp\u003eAir leaving any compressor is warm and saturated. As it cools in the piping that moisture drops out as liquid water, and it ends up in the tool, the finish, the cylinder or the control valve at the far end of the run. A refrigerated dryer chills the air at the compressor so the water condenses and drains there instead of travelling down the line. Buying it integrated rather than as a separate box means one electrical connection, one footprint, no interconnecting pipework to get wrong, and a dryer already matched to this compressor's output rather than guessed at. For paint and finishing work, pneumatic controls, plasma tables and tire service, drying at the source is the difference between a system that works and one that is always being chased with traps and filters.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the AS-B 7.5 HP range the differences come down to storage, air treatment and pressure. The \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e71 gallon tank mount with dryer\u003c\/a\u003e is the same compressor and dryer on a smaller receiver at 593 lbs and a 60 in long footprint, which suits a shop that is tight on floor space and draws air steadily rather than in bursts. The \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003e131 gallon tank mount without a dryer\u003c\/a\u003e is the choice if you already have air treatment downstream. The \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e150 PSI build\u003c\/a\u003e trades airflow for pressure at 27.1 CFM. If you are replacing a compressor on an existing system and keeping the receiver and piping already in place, the \u003ca href=\"\/products\/abac-as-7-5-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003ebase mount build\u003c\/a\u003e is the one to buy at 360 lbs. If the shop is already running short of air, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e10 HP AS-10253TMD\u003c\/a\u003e steps the same package up to 36.4 CFM.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eAutomotive and fleet service bays, tire shops, cabinet and woodworking shops, paint and finishing work, and small production floors where moisture in the air line causes rejects or shortens tool life. Drying the air at the compressor keeps condensate out of the distribution piping instead of leaving it for traps and filters downstream to catch. The 131 gallon receiver stores noticeably more air than the 71 gallon build, which helps when several bays pull on impact tools at the same time.\u003c\/p\u003e\u003ch3\u003eSetting it up\u003c\/h3\u003e\u003cp\u003eGive the cabinet clear air on the cooling side, keep it out of a hot corner, and leave working room at the service panels. The unit measures 76 x 24 x 63 in and weighs 741 lbs, so plan the route in and the pad it sits on before it arrives. Run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller handles menu driven operation and tracks the maintenance intervals for you. Call us with your own flow and duty cycle and we will check this machine against the demand before you pipe it in.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the \u003ca href=\"\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e, built around a fully integrated aluminum block air end, eco friendly vertical oil separation technology and an energy efficient motor. A rotary screw is built for continuous running, so it holds a steady line pressure through a full shift instead of recovering between jobs. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e, the \u003ca href=\"\/collections\/fixed-speed-rotary-screw-air-compressors\"\u003efixed speed screw compressors\u003c\/a\u003e, and our \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C at 109 PSI. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54719451136275,"sku":"4152044129","price":9932.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54719451169043,"sku":"4152043903","price":9932.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/AS-B7.jpg?v=1790177612"},{"product_id":"abac-as-7-5-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor","title":"ABAC AS-7.5501TMD 7.5 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 150 PSI, 27.1 CFM, 67 dBA","description":"\u003cp\u003eThe ABAC AS-7.5501TMD is a complete compressed air station in one package. A 7.5 HP rotary screw air end, a 131 gallon air receiver and a refrigerated dryer arrive mounted and plumbed on a single frame, so there is no separate tank or dryer to source, site and pipe. It delivers 27.1 CFM at a 150 PSI maximum and runs at 67 dBA, quiet enough to sit in the work area instead of a separate compressor room. Choose 230V single-phase (AS-7.5501TMD, part 4152044130) or 208-230-460V three-phase (AS-7.5503TMD, part 4152043904).\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModels: AS-7.5501TMD (230V 1-phase, part 4152044130) \/ AS-7.5503TMD (208-230-460V 3-phase, part 4152043904)\u003c\/li\u003e\n\u003cli\u003eMotor: 7.5 HP\u003c\/li\u003e\n\u003cli\u003eAir delivery: 27.1 CFM, rated by ABAC at 138 PSI\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 67 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 230\/1\/60 or 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 741 lbs | Dimensions: 76\" x 24\" x 63\"\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eVertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the three-in-one build\u003c\/h3\u003e\u003cp\u003eBuying compressor, receiver and dryer separately means three deliveries, three footprints and interconnecting pipe that has to be sized, supported and leak tested. This build arrives as one unit on one pad. The dryer sits downstream of the receiver, so water drops out before it reaches the distribution piping, and the 131 gallon receiver gives the screw somewhere to put air during demand spikes instead of loading and unloading against a short line. For a shop with one electrical drop and limited floor space, that is the difference between a day of installation and a week of it.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003ePaint and finishing work, automotive service bays, tire shops, cabinet and woodworking shops, and small production floors where moisture in the air line causes rejects or tool wear. At 27.1 CFM this unit carries a dual action sander, a couple of impact wrenches, or a spray gun with headroom, run continuously rather than in bursts. The 150 PSI build trades some flow for higher line pressure against the 125 PSI version, which helps where tools or equipment are rated above a standard 125 PSI supply.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eThe \u003ca href=\"\/products\/abac-as-7-5-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e71 gallon version\u003c\/a\u003e of this same machine is 593 lbs on a 60 x 23 in footprint, which suits a shop that is short on floor space and draws air steadily rather than in heavy bursts. If a receiver and dryer are already installed, the \u003ca href=\"\/products\/abac-as-7-5-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-7.5501BM base mount\u003c\/a\u003e is the same air end without the tank or the dryer. Where flow rather than pressure is the constraint, the \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e125 PSI build\u003c\/a\u003e on the same receiver gives 30.5 CFM instead of 27.1.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. A rotary screw is built for continuous running, so it holds a steady line pressure through a full shift instead of recovering between jobs. See the full range of \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e, or browse \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e if you are adding treatment to a compressor you already own.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"230V 1-Phase","offer_id":54745860243731,"sku":"4152044130","price":9932.0,"currency_code":"USD","in_stock":true},{"title":"208-230-460V 3-Phase","offer_id":54745860276499,"sku":"4152043904","price":9932.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-7-5-131-gallon-dryer-150psi.png?v=1789769144"},{"product_id":"abac-as-10-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor","title":"ABAC AS-10253TM 10 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 125 PSI, 36.4 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-10253TM is the 125 PSI, 131 gallon tank mount build of the 10 HP machine in the AS-B screw range. It delivers 36.4 CFM at a 125 PSI maximum and runs at 69 dBA, quiet enough to sit in the work area instead of a separate compressor room. This is the highest airflow setting offered on the 10 HP air end, so it is the one to specify when the shop is short of air rather than short of pressure. The air end and the receiver arrive as one assembled package on a 76 x 24 in footprint, so there is no separate tank to source, set and plumb. At 714 lbs it is the large receiver option in the 10 HP family, the one to buy when demand is intermittent and you want the compressor to run longer and rest longer rather than load and unload all day. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10253TM (part number 4152043897)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 36.4 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 714 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 24 x 63 in\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access for optimizing operating performance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops using air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end limits air loss by design, and ABAC pairs it with an energy efficient motor and a digital controller, so the operating menus and the service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 131 gallon receiver underneath it is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow, receiver size and mounting all move independently. The \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TM\u003c\/a\u003e is the identical 714 lb package set for 150 PSI, trading 2.3 CFM of airflow for the extra pressure. If floor space is the constraint, the \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TM7\u003c\/a\u003e carries the same 36.4 CFM on a 71 gallon receiver at 567 lbs and a 60 x 23 in footprint. The \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TMD\u003c\/a\u003e is this same 131 gallon build with a refrigerated dryer already integrated, which saves plumbing a separate dryer in. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-10-10-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253BM\u003c\/a\u003e is the bare 419 lb base mount at the same pressure and airflow. Stepping down, the \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251TM\u003c\/a\u003e gives 30.5 CFM at 67 dBA on a 131 gallon tank; stepping up, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TM\u003c\/a\u003e carries 52.1 CFM. If noise is the deciding factor, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253TM\u003c\/a\u003e is the quieter 10 HP air end at 65 dBA and 39.8 CFM on the same 125 PSI setting. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, larger automotive and fleet service shops, tire and truck bays, cabinet and woodworking shops, plasma and laser tables, packaging lines, and any operation where a piston compressor is cycling too hard to keep up. At 36.4 CFM it will keep several air ratchets, an orbital sander or a continuous blow off fed through a shift without the line pressure sagging. The 131 gallon receiver stores roughly twice the air of the 71 gallon build, which matters when several bays hit the header at once or when a single large tool draws a short, heavy burst. The tank mount build is the one to buy for a shop starting its compressed air system from nothing, because the receiver, the mounts and the interconnecting pipe are already done and the installer only has to land power and tie into the header.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals. Air leaving any screw carries moisture, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 36.4 CFM the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eABAC COOL 50\u003c\/a\u003e gives useful headroom and runs on 115V, so it plugs in beside the compressor without new wiring; the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eCOOL 35\u003c\/a\u003e is the minimum size. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":54746897580307,"sku":"4152043897","price":8114.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-tank-mount-rotary-screw-air-compressor_efe6b76b-285d-400b-941d-d458b7c46df1.png?v=1790946147"},{"product_id":"abac-as-10-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor","title":"ABAC AS-10503TM 10 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 150 PSI, 34.1 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-10503TM is the 150 PSI, 131 gallon tank mount build of the 10 HP machine in the AS-B screw range. It delivers 34.1 CFM at a 150 PSI maximum and runs at 69 dBA, quiet enough to sit in the work area instead of a separate compressor room. This is the pressure setting to specify when a tool or a piece of production equipment is rated above a standard 125 PSI line, and it trades 2.3 CFM against the 125 PSI build to get there. The air end and the receiver arrive as one assembled package on a 76 x 24 in footprint, so there is no separate tank to source, set and plumb. At 714 lbs it is the large receiver option in the 10 HP family, the one to buy when demand is intermittent and you want the compressor to run longer and rest longer rather than load and unload all day. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10503TM (part number 4152043898)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 34.1 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 714 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 24 x 63 in\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access for optimizing operating performance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops using air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end limits air loss by design, and ABAC pairs it with an energy efficient motor and a digital controller, so the operating menus and the service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 131 gallon receiver underneath it is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow, receiver size and mounting all move independently. The \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TM\u003c\/a\u003e is the identical 714 lb package set for 125 PSI, giving 36.4 CFM if your tools do not actually need the extra pressure. If floor space is the constraint, the \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TM7\u003c\/a\u003e carries the same 34.1 CFM on a 71 gallon receiver at 567 lbs. The \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TMD\u003c\/a\u003e is this same 131 gallon build with a refrigerated dryer already integrated, which saves plumbing a separate dryer in. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-10-10-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503BM\u003c\/a\u003e is the bare 419 lb base mount at the same pressure and airflow. Stepping down, the \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-7.5501TM\u003c\/a\u003e gives 27.1 CFM at 67 dBA on a 131 gallon tank; stepping up, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TM\u003c\/a\u003e carries 46.4 CFM. If noise is the deciding factor, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503TM\u003c\/a\u003e is the quieter 10 HP air end at 65 dBA and 35.6 CFM on the same 150 PSI setting. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, larger automotive and fleet service shops, tire and truck bays, cabinet and woodworking shops, plasma and laser tables, packaging lines, and any operation where a piston compressor is cycling too hard to keep up. The 150 PSI setting matters where a press, a clamping fixture, a truck tire bead seater or an older air tool wants more than a 125 PSI header will give after line losses. At 34.1 CFM it will keep several air ratchets, an orbital sander or a continuous blow off fed through a shift without the line pressure sagging. The 131 gallon receiver stores roughly twice the air of the 71 gallon build, which matters when several bays hit the header at once or when a single large tool draws a short, heavy burst.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals. Air leaving any screw carries moisture, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 34.1 CFM the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eABAC COOL 50\u003c\/a\u003e gives useful headroom and runs on 115V, so it plugs in beside the compressor without new wiring; the \u003ca href=\"\/products\/abac-cool-35-refrigerated-air-dryer-115v\"\u003eCOOL 35\u003c\/a\u003e is the minimum size. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":54747174109459,"sku":"4152043898","price":8114.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-tank-mount-rotary-screw-air-compressor_84af8bc2-02a7-4330-8a4e-5089c5c3edce.png?v=1790946149"},{"product_id":"abac-as-10-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor","title":"ABAC AS-10253TMD 10 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 125 PSI, 36.4 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-10253TMD is a complete compressed air station in one package: a 10 HP rotary screw compressor, a 131 gallon air receiver and a refrigerated dryer, mounted and plumbed as a single factory assembly. It delivers 36.4 CFM at 125 PSI and runs at 69 dBA. Nothing has to be sourced, sited and piped separately, so installation comes down to setting it in place, landing power and tying into the header. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10253TMD (part number 4152043907)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP\u003c\/li\u003e\n\u003cli\u003eAir delivery: 36.4 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 800 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 24 x 63 in\u003c\/li\u003e\n\u003cli\u003eIntegrated air end block of aluminum construction\u003c\/li\u003e\n\u003cli\u003eVertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance intervals\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy the three in one package\u003c\/h3\u003e\n\u003cp\u003eA rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs the way a piston machine does. The catch is that air leaving any screw comes out hot and saturated, so a dryer is not optional on a system feeding paint, pneumatic controls or precision tools. Buying the compressor, the receiver and the refrigerated dryer as one factory assembly removes the part of the job that usually goes wrong: no separate dryer to size and source, no interconnecting pipe to fabricate, no second set of mounts, and no chance of a dryer undersized for the air end in front of it. The 131 gallon receiver underneath keeps the screw from short cycling, which is the one duty pattern a screw genuinely dislikes.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eWithin the 10 HP AS machines, pressure and airflow trade directly against each other on the same hardware. This is the 125 PSI build, which is the airflow end of that trade at 36.4 CFM; the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TMD\u003c\/a\u003e is the identical package set for 150 PSI at 34.1 CFM. If the shop already has drying handled, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TM\u003c\/a\u003e is this same 131 gallon build without the dryer at 714 lbs, and the \u003ca href=\"\/products\/abac-as-10-10-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253BM\u003c\/a\u003e is the bare base mount at 419 lbs on a 32 x 24 in footprint for a plant that already owns a receiver. The \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TMD7\u003c\/a\u003e is the same compressor and dryer on a 71 gallon receiver at 653 lbs, which fits a tighter floor plan but stores roughly 60 gallons less air, so heavy intermittent draws hit the air end harder. For a quieter machine with more air on the same 10 HP, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253TMD\u003c\/a\u003e uses the 10S air end for 39.8 CFM at 65 dBA, and if 36.4 CFM is short of what the tool list draws, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TMD\u003c\/a\u003e holds 125 PSI at 52.1 CFM.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003ePaint and finishing work, production and fabrication floors, larger automotive and fleet service bays, tire and truck shops, and cabinet and woodworking shops where moisture in the air line causes rejects or tool wear. The integrated dryer removes water before it reaches the distribution piping, which matters anywhere air touches a finish, a pneumatic control or a precision tool. At 125 PSI this is the build to specify when the shop wants volume rather than pressure: more air for sanders, blow-off stations and multiple bays running at once, on a receiver large enough that a sudden heavy draw does not pull the header down.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals, so keep a spare set on the shelf. The refrigerated dryer is already fitted, so the remaining air treatment decision is filtration: a particulate and coalescing filter set behind the dryer protects tools and finishes from pipe scale and oil carryover. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the wider \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eUnit performance measured according to ISO 1217 Annex C; CFM quoted at 109 PSI for 125 PSI maximum units. Noise level measured according to ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":54748644213011,"sku":"4152043907","price":9153.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as10-71gal-tank-mount-dryer-125-psi-rotary-screw-air-compressor_664a24e6-d2d7-4490-a34c-dc291b72bf6f.png?v=1790372127"},{"product_id":"abac-as-10-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor","title":"ABAC AS-10503TMD 10 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 150 PSI, 34.1 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-10503TMD is a complete compressed air station in one package: a 10 HP rotary screw compressor, a 131 gallon air receiver and a refrigerated dryer, mounted and plumbed as a single factory assembly. It delivers 34.1 CFM at a 150 PSI maximum and runs at 69 dBA. This is the pressure setting to specify when a tool or a piece of production equipment is rated above a standard 125 PSI line, and it trades 2.3 CFM against the 125 PSI build to get there. Nothing has to be sourced, sited and piped separately, so installation comes down to setting it in place, landing power and tying into the header. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10503TMD (part number 4152043908)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP\u003c\/li\u003e\n\u003cli\u003eAir delivery: 34.1 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 800 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 24 x 63 in\u003c\/li\u003e\n\u003cli\u003eIntegrated air end block of aluminum construction\u003c\/li\u003e\n\u003cli\u003eVertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance intervals\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy the three in one package\u003c\/h3\u003e\n\u003cp\u003eA rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs the way a piston machine does. The catch is that air leaving any screw comes out hot and saturated, so a dryer is not optional on a system feeding paint, pneumatic controls or precision tools. Buying the compressor, the receiver and the refrigerated dryer as one factory assembly removes the part of the job that usually goes wrong: no separate dryer to size and source, no interconnecting pipe to fabricate, no second set of mounts, and no chance of a dryer undersized for the air end in front of it. The 131 gallon receiver underneath keeps the screw from short cycling, which is the one duty pattern a screw genuinely dislikes.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eWithin the 10 HP AS machines, pressure and airflow trade directly against each other on the same hardware. This is the 150 PSI build; the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TMD\u003c\/a\u003e is the identical 800 lb package set for 125 PSI at 36.4 CFM, which is the one to buy if the tool list does not actually need the extra pressure. If the shop already has drying handled, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TM\u003c\/a\u003e is this same 131 gallon build without the dryer at 714 lbs, and the \u003ca href=\"\/products\/abac-as-10-10-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503BM\u003c\/a\u003e is the bare base mount at 419 lbs on a 32 x 24 in footprint for a plant that already owns a receiver. The \u003ca href=\"\/products\/abac-as-10-10-hp-71-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TMD7\u003c\/a\u003e is the same compressor and dryer on a 71 gallon receiver at 653 lbs, which fits a tighter floor plan but stores roughly 60 gallons less air, so heavy intermittent draws hit the air end harder. For a quieter machine with more air on the same 10 HP, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503TMD\u003c\/a\u003e uses the 10S air end for 35.6 CFM at 65 dBA, and if 34.1 CFM is short of what the shop draws, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TMD\u003c\/a\u003e holds 150 PSI at 46.4 CFM.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003ePaint and finishing work, production and fabrication floors, larger automotive and fleet service bays, tire and truck shops, and cabinet and woodworking shops where moisture in the air line causes rejects or tool wear. The integrated dryer removes water before it reaches the distribution piping, which matters anywhere air touches a finish, a pneumatic control or a precision tool. The 150 PSI setting earns its place where a press, a clamping fixture, a truck tire bead seater or an older air tool wants more than a 125 PSI header will give after line losses. The 131 gallon receiver stores roughly 60 gallons more air than the 71 gallon build, which softens the effect of short heavy draws such as impact tools, blow-off stations and cabinet blasting.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals, so keep a spare set on the shelf. The refrigerated dryer is already fitted, so the remaining air treatment decision is filtration: a particulate and coalescing filter set behind the dryer protects tools and finishes from pipe scale and oil carryover. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the wider \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eUnit performance measured according to ISO 1217 Annex C. Noise level measured according to ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67527774109971,"sku":"4152043908","price":9153.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as10-131gal-tank-mount-dryer-150-psi-rotary-screw-air-compressor.png?v=1790373943"},{"product_id":"abac-as-10s-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor","title":"ABAC AS-10S253TM 10 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 125 PSI, 39.8 CFM, 65 dBA","description":"\u003cp\u003eThe ABAC AS-10S253TM is the quiet, higher output 10 HP machine in the AS-B range, delivered on a 131 gallon air receiver as one assembled package. It gives 39.8 CFM at a 125 PSI maximum and runs at just 65 dBA, about 4 dBA below the standard AS-10 and quiet enough to stand on the shop floor near the point of use instead of being walled into a compressor room. Because the air end and the tank ship together, installation comes down to setting it in place, landing power and tying into the header. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10S253TM (part number 4152043918)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 39.8 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 65 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eThree stage vertical oil separation, low oil consumption\u003c\/li\u003e\n\u003cli\u003eIntuitive digital controller with programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003eCFM for 10S through 20 HP units quoted as free air delivery per ISO 1217 Annex C. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops running air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end is a fully integrated aluminum block with vertical oil separation, which keeps oil carryover and condensation low, and ABAC pairs it with an energy efficient motor and a digital controller so the service schedule lives on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 131 gallon receiver underneath it is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow and mounting move independently. The \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503TM\u003c\/a\u003e is the identical package set for 150 PSI at 35.6 CFM, and the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-10S753TM\u003c\/a\u003e reaches 175 PSI at 29.9 CFM, so every step up in pressure costs airflow. Against the standard \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TM\u003c\/a\u003e on the same 131 gallon tank at the same 125 PSI, this unit gives 3.4 CFM more air and runs 4 dBA quieter. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-10s-10-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253BM\u003c\/a\u003e is the bare 454 lb base mount at the same pressure and airflow. The \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253TMD\u003c\/a\u003e is this same tank mount build with a refrigerated dryer already integrated, which saves plumbing a separate dryer in. Stepping down, the \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251TM\u003c\/a\u003e gives 30.5 CFM at 67 dBA on the same receiver; stepping up, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TM\u003c\/a\u003e carries 52.1 CFM at 69 dBA.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, automotive and fleet service bays, tire and truck shops, cabinet and woodworking shops, plasma tables, packaging lines, and any operation where a piston compressor is cycling too hard to hold line pressure. At 39.8 CFM it will carry several air ratchets, an orbital sander and a plasma cutter on the same line, or keep a two to three bay shop fed through a full shift. The 131 gallon receiver gives the compressor room to ride out short bursts of heavy demand, so it runs longer and rests longer rather than loading and unloading all day. The 65 dBA rating is the reason to choose this one over the standard AS-10 when the compressor has to share space with the people using it.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals. Air leaving any screw carries moisture, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 39.8 CFM the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eABAC COOL 50\u003c\/a\u003e is the matching 50 CFM size and runs on 115V, so it plugs in beside the compressor without new wiring; the \u003ca href=\"\/products\/abac-cool-65-refrigerated-air-dryer-115v\"\u003eCOOL 65\u003c\/a\u003e is the next size up if you want more headroom. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer range\u003c\/a\u003e. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67544941854995,"sku":"4152043918","price":8575.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-tank-mount-rotary-screw-air-compressor_4b9500e2-6ea7-49db-a8dd-78cb5bbc9ffe.png?v=1790946148"},{"product_id":"abac-as-10s-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor","title":"ABAC AS-10S503TM 10 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 150 PSI, 35.6 CFM, 65 dBA","description":"\u003cp\u003eThe ABAC AS-10S503TM is a 10 HP rotary screw air compressor and a 131 gallon air receiver supplied as one factory assembly, built for shops that need steady air all shift rather than the stop and start cycle of a piston unit. It delivers 35.6 CFM at 150 PSI and runs at 65 dBA, because this is the quiet 10S air end rather than the standard 10 HP block, so the machine can sit on the shop floor instead of in a separate compressor room. The screw unit and the tank ship mounted and plumbed together, so installation comes down to setting it in place, wiring it and connecting your air line. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10S503TM (part number 4152043919)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 35.6 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 65 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 750 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eFully integrated air end block of aluminum construction\u003c\/li\u003e\n\u003cli\u003e3-stage vertical oil separation process\u003c\/li\u003e\n\u003cli\u003eSmart digital controller for monitoring and service intervals\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy the quiet air end\u003c\/h3\u003e\n\u003cp\u003eABAC builds two 10 HP air ends. The standard block in the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TM\u003c\/a\u003e gives 34.1 CFM at 150 PSI and 69 dBA on the same size receiver. The 10S block in this machine gives 35.6 CFM at the same pressure and 65 dBA. Four decibels is roughly half the perceived loudness, which is usually what decides whether the compressor gets its own room or lives in the corner of the shop. The extra 1.5 CFM is useful, but the noise figure is the reason most buyers pay the difference. The trade is weight and footprint: 750 lbs over 76 x 27 x 62 in against 714 lbs on the standard build.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the 10S air end, pressure and airflow trade directly against each other on identical hardware. This machine sits in the middle of that trade. The \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253TM\u003c\/a\u003e is the same 750 lb package set for 125 PSI at 39.8 CFM, and the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-10S753TM\u003c\/a\u003e runs 175 PSI at 29.9 CFM. Buy pressure only to the level your highest tool actually needs, because every step up costs air. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-10s-10-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503BM\u003c\/a\u003e is this same air end as a bare base mount at 454 lbs on a 37 x 28 in footprint. If 35.6 CFM is short of what your tool list draws, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TM\u003c\/a\u003e holds 150 PSI at 46.4 CFM on the same 76 x 27 x 62 in platform.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, automotive and fleet service bays, tire and truck shops, cabinet and woodworking shops, and any operation where a reciprocating compressor is working too hard to hold line pressure. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. The 150 PSI rating suits shops running impact tools, pneumatic presses or clamping equipment that need pressure above the common 125 PSI setting, and the 131 gallon receiver underneath keeps the screw from short cycling, which is the one duty pattern a screw genuinely dislikes.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eAir leaving any rotary screw is hot and saturated, so drying is the next decision rather than an optional extra. If your air feeds paint, pneumatic controls or precision tools, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503TMD\u003c\/a\u003e is this exact machine with a refrigerated dryer fitted and plumbed at the factory, 844 lbs on the same footprint, which removes the job of sizing, siting and piping a separate dryer. A particulate and coalescing filter set behind the dryer protects tools and finishes from pipe scale and oil carryover. Give the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items and the digital controller tracks the intervals, so keep a spare set on the shelf. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eUnit performance measured according to ISO 1217 Annex C; for 10S to 20 HP machines CFM figures are quoted at free air delivery. Noise level measured according to ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67546950074643,"sku":"4152043919","price":8854.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-tank-mount-rotary-screw-air-compressor_6a4b8909-05d8-4af2-8b5b-348578473165.png?v=1790946149"},{"product_id":"abac-as-10s-10-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor","title":"ABAC AS-10S753TM 10 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 175 PSI, 29.9 CFM, 65 dBA","description":"\u003cp\u003eThe ABAC AS-10S753TM is a 10 HP rotary screw compressor and a 131 gallon air receiver supplied as one factory assembly, built for shops that need steady air all shift rather than the stop and start cycle of a piston unit. It delivers 29.9 CFM at 175 PSI and runs at 65 dBA, quiet enough to sit on the shop floor instead of in a separate compressor room. This is the quiet 10S air end set to the highest pressure offered on a 10 HP AS machine, so it is the build to specify when a tool on the line genuinely needs 175 PSI rather than more volume. Because the screw unit and the tank ship mounted and plumbed together, installation comes down to setting it in place, wiring it and connecting your air line. Power is 208-230-460V three phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10S753TM (part number 4152043920)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 29.9 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 65 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 750 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eIntegrated air end block of aluminum construction\u003c\/li\u003e\n\u003cli\u003e3-stage vertical oil separation process\u003c\/li\u003e\n\u003cli\u003eIntuitive digital controller for monitoring and service intervals\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a tank mounted screw\u003c\/h3\u003e\n\u003cp\u003eA rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs the way a piston machine does. The one duty pattern a screw genuinely dislikes is short cycling, and the 131 gallon receiver underneath this machine is what prevents it: the tank absorbs short bursts of demand so the air end runs loaded for useful stretches rather than starting and unloading every few seconds. Buying the compressor and the receiver as a single factory assembly also removes the part of the install that usually goes wrong. There is no separate tank to site, no interconnecting pipe to fabricate and no second set of mounts. The installer lands power and ties into the header. Air leaving any screw comes out hot and saturated, so if the system feeds paint, pneumatic controls or precision tools, plan on drying it; see the comparison below for the factory dryer build.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the 10S air end, pressure and airflow trade directly against each other on identical hardware, and this machine sits at the pressure end of that trade. The \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503TM\u003c\/a\u003e is the same 750 lb package set for 150 PSI at 35.6 CFM, and the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253TM\u003c\/a\u003e runs 125 PSI at 39.8 CFM. Going from 125 to 175 PSI costs roughly 10 CFM on the same 10 HP motor, so buy pressure only to the level your highest tool actually needs. If you want drying handled in the same package, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003eAS-10S753TMD\u003c\/a\u003e is this same build with an integrated refrigerated dryer at 844 lbs. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-10s-10-hp-base-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-10S753BM\u003c\/a\u003e is the bare base mount at 454 lbs on a 37 x 28 in footprint. Within the 10 HP AS machines the 175 PSI rating is offered on the 10S air end only, so this is the 10 HP route to that pressure. If 29.9 CFM is short of what your tool list draws, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-15753TM\u003c\/a\u003e holds the same 175 PSI at 41.7 CFM.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eWork that a 125 or 150 PSI machine cannot cover: pneumatic presses and clamping fixtures, air operated diaphragm pumps, laser cutting assist gas, sandblasting cabinets, and heavy impact tooling that loses torque the moment line pressure drops. It also handles ordinary production and fabrication duty alongside those, with the headroom to run a long pipe drop without the pressure at the far end falling below what the tool is rated for. Automotive and fleet service bays, tire and truck shops, cabinet and woodworking shops, and any operation where a reciprocating compressor is working too hard to hold line pressure are all good fits. At 65 dBA the machine can sit in the work area rather than in a dedicated compressor room, which is often what decides the 10S over the standard air end when the compressor shares a room with the people using it.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Confirm your piping, fittings and hose are rated above 175 PSI before you commission it, because a system assembled around a 125 PSI machine is not automatically suited to this one. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals, so keep a spare set on the shelf. There is no dryer fitted to this build, so air treatment is the open decision: a refrigerated dryer sized to 29.9 CFM plus a particulate and coalescing filter set behind it will keep water, pipe scale and oil carryover out of your distribution piping. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the wider \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eUnit performance measured according to ISO 1217 Annex C; for 10S to 20 HP machines CFM figures are quoted at free air delivery. Noise level measured according to ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67546992902419,"sku":"4152043920","price":7437.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-tank-mount-rotary-screw-air-compressor_b81a060f-e681-44f3-b97e-fba914c3c0ba.png?v=1790946148"},{"product_id":"abac-as-10s-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor","title":"ABAC AS-10S253TMD 10 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 125 PSI, 39.8 CFM, 65 dBA","description":"\u003cp\u003eThe ABAC AS-10S253TMD is a complete compressed air station in one package: a 10 HP rotary screw compressor, a 131 gallon air receiver and a refrigerated dryer, mounted and plumbed as a single assembly. It delivers 39.8 CFM at 125 PSI and runs at 65 dBA, quiet enough to sit in the work area instead of a separate compressor room. This is the quiet 10S air end, the highest airflow 10 HP machine in the AS-B range, and the 125 PSI build is the one to specify when the shop is short of air rather than short of pressure. There is no separate tank or dryer to source, site and pipe, so installation comes down to setting it in place, wiring it and connecting your air line. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10S253TMD (part number 4152043927)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 39.8 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 65 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 844 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eIntegrated air end block of aluminum construction\u003c\/li\u003e\n\u003cli\u003e3-stage vertical oil separation process\u003c\/li\u003e\n\u003cli\u003eIntuitive digital controller for monitoring and service intervals\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy the three in one package\u003c\/h3\u003e\n\u003cp\u003eA rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs the way a piston machine does. The catch is that air leaving any screw comes out hot and saturated, so a dryer is not optional on a system feeding paint, pneumatic controls or precision tools. Buying the compressor, the receiver and the refrigerated dryer as one factory assembly removes the part of the job that usually goes wrong: no separate dryer to size and source, no interconnecting pipe to fabricate, no second set of mounts, and no chance of a dryer undersized for the air end in front of it. The installer lands power and ties into the header. The 131 gallon receiver underneath keeps the screw from short cycling, which is the one duty pattern a screw genuinely dislikes.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the 10S air end, pressure and airflow trade directly against each other on identical hardware. The \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503TMD\u003c\/a\u003e is the same 844 lb package set for 150 PSI at 35.6 CFM, and the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003eAS-10S753TMD\u003c\/a\u003e runs 175 PSI at 29.9 CFM. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow. If you already have drying handled, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253TM\u003c\/a\u003e is this same 131 gallon build without the dryer at 750 lbs, and the \u003ca href=\"\/products\/abac-as-10s-10-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253BM\u003c\/a\u003e is the bare base mount at 454 lbs on a 37 x 28 in footprint for a shop that already owns a receiver. Against the standard 10 HP air end, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10253TMD\u003c\/a\u003e gives 36.4 CFM at 69 dBA on the same tank, so the 10S buys roughly 3 CFM more air and about 4 dBA less noise for the same 10 HP. Stepping down, the \u003ca href=\"\/products\/abac-as-7-5-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-7.5251TMD\u003c\/a\u003e carries 30.5 CFM with a dryer; stepping up, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TMD\u003c\/a\u003e carries 52.1 CFM.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003ePaint and finishing booths, production and fabrication floors, automotive and fleet service bays, tire and truck shops, plasma and laser tables, packaging lines, and cabinet and woodworking shops where moisture in the air line causes rejects or tool wear. At 39.8 CFM it will keep several air ratchets, an orbital sander or a continuous blow off fed through a shift without the line pressure sagging. The integrated dryer removes water before it reaches the distribution piping, which matters anywhere air touches a finish, a pneumatic control or a precision tool. At 65 dBA the machine can sit in the work area rather than in a dedicated compressor room, which is often what decides the 10S over the standard air end when the compressor shares a room with the people using it.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals, so keep a spare set on the shelf. The refrigerated dryer is already fitted, so the remaining air treatment decision is filtration: a particulate and coalescing filter set behind the dryer protects tools and finishes from pipe scale and oil carryover. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the wider \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eUnit performance measured according to ISO 1217 Annex C; for 10S to 20 HP machines CFM figures are quoted at free air delivery. Noise level measured according to ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67574836101395,"sku":"4152043927","price":11787.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-131-gallon-tank-mount-dryer-rotary-screw-air-compressor.png?v=1790946107"},{"product_id":"abac-as-10s-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor","title":"ABAC AS-10S503TMD 10 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 150 PSI, 35.6 CFM, 65 dBA","description":"\u003cp\u003eThe ABAC AS-10S503TMD is a complete compressed air station in one package: a 10 HP rotary screw compressor on the quiet 10S air end, a 131 gallon air receiver and a refrigerated dryer, mounted and plumbed as a single factory assembly. It delivers 35.6 CFM at 150 PSI and runs at 65 dBA, quiet enough to sit in the work area instead of a separate compressor room. There is no separate tank or dryer to source, site and pipe, so installation comes down to setting it in place, wiring it and connecting your air line. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10S503TMD (part number 4152043928)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 35.6 CFM free air delivery\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 65 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 844 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eIntegrated air end block of aluminum construction\u003c\/li\u003e\n\u003cli\u003e3-stage vertical oil separation process\u003c\/li\u003e\n\u003cli\u003eIntuitive digital controller for monitoring and service intervals\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy the three in one package\u003c\/h3\u003e\n\u003cp\u003eA rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs the way a piston machine does. The catch is that air leaving any screw comes out hot and saturated, so a dryer is not optional on a system feeding paint, pneumatic controls or precision tools. Buying the compressor, the receiver and the refrigerated dryer as one factory assembly removes the part of the job that usually goes wrong: no separate dryer to size and source, no interconnecting pipe to fabricate, no second set of mounts, and no chance of a dryer undersized for the air end in front of it. The installer lands power and ties into the header. The 131 gallon receiver underneath keeps the screw from short cycling, which is the one duty pattern a screw genuinely dislikes.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAt 150 PSI this is the middle setting of the three pressures offered on the 10S air end, and on identical hardware pressure and airflow trade directly against each other. The \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253TMD\u003c\/a\u003e is the same 844 lb package set for 125 PSI at 39.8 CFM, and the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003eAS-10S753TMD\u003c\/a\u003e runs 175 PSI at 29.9 CFM. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow on the same 10 HP motor. Set against the standard 10 HP package on the same tank, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TMD\u003c\/a\u003e delivers 34.1 CFM at 69 dBA, so the 10S buys about 1.5 CFM more air and 4 dBA less noise, which matters when the compressor shares a room with the people using it. If drying is already handled upstream, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503TM\u003c\/a\u003e is this same 131 gallon build without the dryer at 750 lbs, and the \u003ca href=\"\/products\/abac-as-10s-10-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503BM\u003c\/a\u003e is the bare base mount at 454 lbs on a 37 x 28 in footprint for a shop that already owns a receiver. If 35.6 CFM is short of what your tool list draws, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TMD\u003c\/a\u003e holds the same 150 PSI at 46.4 CFM.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003ePaint and finishing work, production and fabrication floors, automotive and fleet service bays, tire and truck shops, heavy assembly, cleaning and parts preparation, and cabinet and woodworking shops where moisture in the air line causes rejects or tool wear. The integrated dryer removes water before it reaches the distribution piping, which matters anywhere air touches a finish, a pneumatic control or a precision tool. The 150 PSI build is the one to choose when tools, presses or a plant header need pressure above the usual 125 PSI shop standard, and the 65 dBA rating lets it sit on the floor it serves rather than in a dedicated room.\u003c\/p\u003e\n\u003cp\u003ePart of the ABAC AS-B screw range from the \u003ca href=\"\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e, our \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e if you are drying an existing system, or browse all \u003ca href=\"\/collections\/air-compressors\"\u003estationary air compressors\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted as free air delivery. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67574893642003,"sku":"4152043928","price":11787.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-131-gallon-tank-mount-dryer-rotary-screw-air-compressor_6b6d8fdd-a12b-4270-b10a-a6f9b7c113a0.png?v=1790946157"},{"product_id":"abac-as-10s-10-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor","title":"ABAC AS-10S753TMD 10 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 175 PSI, 29.9 CFM, 65 dBA","description":"\u003cp\u003eThe ABAC AS-10S753TMD is a complete compressed air station in one package: a 10 HP rotary screw compressor, a 131 gallon air receiver and a refrigerated dryer, mounted and plumbed as a single factory assembly. It delivers 29.9 CFM at 175 PSI and runs at 65 dBA, quiet enough to sit in the work area instead of a separate compressor room. This is the quiet 10S air end set to the highest pressure offered on a 10 HP AS machine, which makes it the build to specify when a tool on the line genuinely needs 175 PSI rather than more volume. There is no separate tank or dryer to source, site and pipe, so installation comes down to setting it in place, wiring it and connecting your air line. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-10S753TMD (part number 4152043929)\u003c\/li\u003e\n\u003cli\u003eMotor: 10 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 29.9 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 65 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver with integrated refrigerated dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 844 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eIntegrated air end block of aluminum construction\u003c\/li\u003e\n\u003cli\u003e3-stage vertical oil separation process\u003c\/li\u003e\n\u003cli\u003eIntuitive digital controller for monitoring and service intervals\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy the three in one package\u003c\/h3\u003e\n\u003cp\u003eA rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs the way a piston machine does. The catch is that air leaving any screw comes out hot and saturated, so a dryer is not optional on a system feeding paint, pneumatic controls or precision tools. Buying the compressor, the receiver and the refrigerated dryer as one factory assembly removes the part of the job that usually goes wrong: no separate dryer to size and source, no interconnecting pipe to fabricate, no second set of mounts, and no chance of a dryer undersized for the air end in front of it. The installer lands power and ties into the header. The 131 gallon receiver underneath keeps the screw from short cycling, which is the one duty pattern a screw genuinely dislikes. At 175 PSI the drying step matters more, not less, because compressing further wrings more water out of the air and that condensate has to leave the system before it reaches your piping.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the 10S air end, pressure and airflow trade directly against each other on identical hardware, and this machine sits at the pressure end of that trade. The \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-10S503TMD\u003c\/a\u003e is the same 844 lb package set for 150 PSI at 35.6 CFM, and the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-10S253TMD\u003c\/a\u003e runs 125 PSI at 39.8 CFM. Going from 125 to 175 PSI costs roughly 10 CFM on the same 10 HP motor, so buy pressure only to the level your highest tool actually needs. If you already have drying handled, the \u003ca href=\"\/products\/abac-as-10s-10-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-10S753TM\u003c\/a\u003e is this same 131 gallon build without the dryer at 750 lbs, and the \u003ca href=\"\/products\/abac-as-10s-10-hp-base-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-10S753BM\u003c\/a\u003e is the bare base mount at 454 lbs on a 37 x 28 in footprint for a shop that already owns a receiver. Within the 10 HP AS machines the 175 PSI rating is offered on the 10S air end only, so this is the 10 HP route to that pressure. If 29.9 CFM is short of what your tool list draws, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003eAS-15753TMD\u003c\/a\u003e holds the same 175 PSI at 41.7 CFM.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eWork that a 125 or 150 PSI machine cannot cover: pneumatic presses and clamping fixtures, air-operated diaphragm pumps, laser cutting assist gas, sandblasting cabinets, and heavy impact tooling that loses torque the moment line pressure drops. It also handles the ordinary production and fabrication duties alongside those, with the headroom to run a long pipe drop without the pressure at the far end falling below what the tool is rated for. The integrated dryer removes water before it reaches the distribution piping, which matters anywhere air touches a finish, a pneumatic control or a precision tool. At 65 dBA the machine can sit in the work area rather than in a dedicated compressor room, which is often what decides the 10S over the standard air end when the compressor shares a room with the people using it.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet about 3 feet of clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Confirm your piping, fittings and hose are rated above 175 PSI before you commission it, because a system assembled around a 125 PSI machine is not automatically suited to this one. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals, so keep a spare set on the shelf. The refrigerated dryer is already fitted, so the remaining air treatment decision is filtration: a particulate and coalescing filter set behind the dryer protects tools and finishes from pipe scale and oil carryover. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the wider \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm receiver sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eUnit performance measured according to ISO 1217 Annex C; for 10S to 20 HP machines CFM figures are quoted at free air delivery. Noise level measured according to ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67575561519379,"sku":"4152043929","price":9976.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-b-131-gallon-tank-mount-dryer-rotary-screw-air-compressor_85b8d769-130c-4521-860d-fff52f8f7e61.png?v=1790946157"},{"product_id":"abac-as-15-15-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor","title":"ABAC AS-15253TM 15 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 125 PSI, 52.1 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-15253TM is a 15 HP rotary screw air compressor shipped on a 131 gallon air receiver, built for shops that need steady air through a full shift rather than the stop and start cycle of a piston unit. It delivers 52.1 CFM at 125 PSI and runs at 69 dBA on 208-230-460V three-phase power. Because the screw unit and the tank arrive as one assembly, installation comes down to setting it in place, wiring it and connecting the air line.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AS-15253TM (part number 4152043921)\u003c\/li\u003e\n\u003cli\u003eMotor: 15 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 52.1 CFM\u003c\/li\u003e\n\u003cli\u003eWorking pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 776 lbs | Dimensions: 76\" x 27\" x 62\"\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the tank is part of the machine\u003c\/h3\u003e\u003cp\u003eA rotary screw is built to run continuously, so the receiver is not there to give the compressor a rest the way a piston machine's tank is. It is there to absorb short bursts of demand, to hold line pressure steady when several tools trigger at once, and to knock some of the condensate out of the air before it reaches your piping. Buying the tank already mounted removes the sizing question, the second footprint and the interconnecting pipe, and it is why most shops replacing a worn out 80 gallon piston unit go straight to a tank mount screw.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 15 HP AS-B frame the mounting and the pressure move independently. The \u003ca href=\"\/products\/abac-as-15-15-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-15253BM\u003c\/a\u003e is the same air end with no tank at 478 lbs, for a shop that already owns a receiver, and the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TMD\u003c\/a\u003e is this machine with a dryer built onto the same frame at 871 lbs. Moving up in pressure trades airflow in the identical cabinet: the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TM\u003c\/a\u003e gives 46.4 CFM at 150 PSI and the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-15753TM\u003c\/a\u003e gives 41.7 CFM at 175 PSI. On volume, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003e10 HP AS-10253TM\u003c\/a\u003e delivers 36.4 CFM on the same tank and the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003e20 HP AS-20253TM\u003c\/a\u003e steps up to 60.6 CFM at 71 dBA. Pick the pressure first, because every step up costs airflow, then size the air end to the tool list.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction and fabrication floors, automotive and fleet service bays, tire and truck shops, cabinet and woodworking shops, and any operation where a reciprocating compressor is working too hard to hold line pressure. At 69 dBA the package is quiet enough to sit near the point of use instead of in a separate compressor room, and the 131 gallon receiver carries it through short bursts of heavy demand without short cycling.\u003c\/p\u003e\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\u003cp\u003eThe compressor and the receiver come as one unit, so what is left is drying, filtration and drainage. At 52.1 CFM the usual match is a refrigerated dryer rated above that figure, such as the \u003ca href=\"\/products\/abac-cool-65-refrigerated-air-dryer-115v\"\u003eABAC COOL 65\u003c\/a\u003e, with a condensate drain on the tank so the water it knocks out actually leaves the system. If you would rather have the dryer factory piped and wired onto the frame, buy the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TMD\u003c\/a\u003e instead and skip the second install.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the Atlas Copco group. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C at free air delivery. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67577761431827,"sku":"4152043921","price":9714.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-15253tm.png?v=1790951007"},{"product_id":"abac-as-15-15-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor","title":"ABAC AS-15503TM 15 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 150 PSI, 46.4 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-15503TM is the 150 PSI build of the 15 HP machine in the AS-B screw range, delivered on a 131 gallon horizontal receiver as a single assembly. It puts out 46.4 CFM at a 150 PSI maximum and runs at 69 dBA, quiet enough to sit in the work area rather than a separate compressor room. Tank mount is the configuration to buy when there is no receiver already in the plant: compressor, tank and controls arrive piped and wired together, so installation comes down to setting it on the floor, bringing power to it and connecting the air line. At 776 lbs in a 76 x 27 x 62 in footprint it takes roughly the floor space of a workbench. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-15503TM (part number 4152043922)\u003c\/li\u003e\n\u003cli\u003eMotor: 15 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 46.4 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 776 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access for programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops using air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end is built around a state of the art design that limits air loss, and ABAC pairs it with an energy efficient motor and a digital controller, so the operating menus and the service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 131 gallon receiver underneath this one is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow and mounting all move independently. The \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TM\u003c\/a\u003e is the same 15 HP machine set for 125 PSI, trading pressure for airflow at 52.1 CFM on the identical tank, and the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-15753TM\u003c\/a\u003e goes the other way to 175 PSI and 41.7 CFM. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow. Stepping down in power, the \u003ca href=\"\/products\/abac-as-10-10-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-10503TM\u003c\/a\u003e gives 34.1 CFM at the same 150 PSI; stepping up, the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-20503TM\u003c\/a\u003e carries 54 CFM at 71 dBA. If you already own a receiver, the same air end comes as the \u003ca href=\"\/products\/abac-as-15-15-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-15503BM\u003c\/a\u003e base mount at 478 lbs on a 37 x 28 x 40 in footprint. If you want drying built in, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TMD\u003c\/a\u003e is this exact machine with the refrigerated dryer already mounted and piped.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, larger automotive and fleet service shops, tire and truck bays, cabinet and woodworking shops, plasma and laser tables, packaging lines, and any operation running tooling or a test rig specified above 125 PSI. At 46.4 CFM it will keep a bank of air ratchets, a sander and a continuous blow off fed through a full shift, or several bays working at once without the line pressure sagging. The tank mount build is the one to buy for a new installation, or for a shop replacing a worn piston compressor outright, because it takes receiver sizing and tank piping out of the job.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals. Air leaving any screw carries moisture, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 46.4 CFM the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eABAC COOL 50\u003c\/a\u003e is the minimum size and the \u003ca href=\"\/products\/abac-cool-65-refrigerated-air-dryer-115v\"\u003eCOOL 65\u003c\/a\u003e gives useful headroom; both run on 115V, so they sit beside the compressor without new wiring. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67577764872467,"sku":"4152043922","price":9714.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-15503tm.png?v=1790951864"},{"product_id":"abac-as-15-15-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor","title":"ABAC AS-15753TM 15 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 175 PSI, 41.7 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-15753TM is the 175 PSI build of the 15 HP machine in the AS-B screw range, shipped on a 131 gallon air receiver as a single assembly. It delivers 41.7 CFM at a 175 PSI maximum and runs at 69 dBA on 208-230-460V three-phase power. Because the screw unit and the tank arrive mounted together, installation comes down to setting it in place, wiring it and connecting the air line.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AS-15753TM (part number 4152043923)\u003c\/li\u003e\n\u003cli\u003eMotor: 15 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 41.7 CFM\u003c\/li\u003e\n\u003cli\u003eWorking pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 776 lbs | Dimensions: 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven operation and programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy 175 PSI costs airflow\u003c\/h3\u003e\u003cp\u003eA screw air end turns the same displacement whatever pressure you ask of it, so every step up in discharge pressure takes volume off the top. In this cabinet that is 52.1 CFM at 125 PSI, 46.4 CFM at 150 PSI and 41.7 CFM here at 175 PSI, all from the same 15 HP motor. Specify 175 PSI when a tool or a process genuinely needs it, for example an air over hydraulic press, a high pressure blow off, or a long distribution run that arrives at the bench well below the compressor setpoint. Buying the pressure as headroom costs you a fifth of the air for nothing.\u003c\/p\u003e\u003ch3\u003eWhy the tank is part of the machine\u003c\/h3\u003e\u003cp\u003eA rotary screw is built to run continuously, so the receiver is not there to give the compressor a rest the way a piston machine's tank is. It is there to absorb short bursts of demand, to hold line pressure steady when several tools trigger at once, and to knock condensate out of the air before it reaches your piping. Buying the tank already mounted removes the sizing question, the second footprint and the interconnecting pipe.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 15 HP AS-B frame the mounting and the pressure move independently. The \u003ca href=\"\/products\/abac-as-15-15-hp-base-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-15753BM\u003c\/a\u003e is the same air end with no tank at 478 lbs, for a shop that already owns a receiver, and the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003eAS-15753TMD\u003c\/a\u003e is this machine with a refrigerated dryer built onto the same frame at 871 lbs. Drop the pressure and the airflow comes back: the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TM\u003c\/a\u003e gives 46.4 CFM at 150 PSI and the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TM\u003c\/a\u003e gives 52.1 CFM at 125 PSI on the same receiver. If you need 175 PSI and more volume, the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003e20 HP AS-20753TM\u003c\/a\u003e holds the same pressure at 48.5 CFM and 71 dBA. Pick the pressure first, then size the air end to the tool list.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction and fabrication floors, automotive and fleet service bays, tire and truck shops, plasma cutting, and any operation running tools rated above 150 PSI where a reciprocating compressor is working too hard to hold line pressure. At 69 dBA the package is quiet enough to sit near the point of use instead of in a separate compressor room, and the 131 gallon receiver carries it through short bursts of heavy demand without short cycling.\u003c\/p\u003e\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\u003cp\u003eThe compressor and the receiver come as one unit, so what is left is drying, filtration and drainage. At 41.7 CFM the usual match is a refrigerated dryer rated above that figure, such as the \u003ca href=\"\/products\/abac-cool-50-refrigerated-air-dryer-115v\"\u003eABAC COOL 50\u003c\/a\u003e, with a condensate drain on the tank so the water it knocks out actually leaves the system. If you would rather have the dryer factory piped and wired onto the frame, buy the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003eAS-15753TMD\u003c\/a\u003e instead and skip the second install.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B 5 to 20 HP screw range from the Atlas Copco group. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and our \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C at free air delivery. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67577764905235,"sku":"4152043923","price":9714.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-15753tm.png?v=1790951864"},{"product_id":"abac-as-15-15-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor","title":"ABAC AS-15253TMD 15 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 125 PSI, 52.1 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-15253TMD is the all in one version of ABAC's 15 HP AS-B screw compressor: compressor, 131 gallon receiver and refrigerated air dryer built onto a single frame and shipped as one machine. It delivers 52.1 CFM at a 125 PSI maximum and runs at 69 dBA on 208-230-460V three-phase power. Because the dryer is already plumbed and wired into the package, there is no second unit to size, site, pipe or power, and the air leaving the discharge is already dry. At 871 lbs in a 76 x 27 x 62 in footprint it occupies roughly the floor space of the tank alone.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AS-15253TMD (part number 4152043930)\u003c\/li\u003e\n\u003cli\u003eMotor: 15 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 52.1 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer, factory piped and wired\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 871 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end with vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at free air delivery for the 10S to 20 HP range. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e\u003ch3\u003eWhat the dryer adds to the package\u003c\/h3\u003e\u003cp\u003eABAC lists the same compressor and tank without the dryer at 776 lbs, so the refrigerated dryer accounts for roughly 95 lbs of the 871 lb total and none of the floor space: the cabinet and the 76 x 27 x 62 in footprint are identical either way. That trade matters more than it sounds. A 15 HP screw pushing 52.1 CFM of warm saturated air into cool shop piping will drop a real volume of water somewhere, and the only open question is whether it comes out at the machine or at the drops above your benches. The factory dryer is matched to the 52.1 CFM this unit actually produces, so there is no sizing exercise, no second electrical circuit, and no mismatch between a compressor bought this year and a dryer added later.\u003c\/p\u003e\u003ch3\u003eWhy the 125 PSI build\u003c\/h3\u003e\u003cp\u003eThe AS-15 cabinet is sold at three pressures and the airflow moves with it: 52.1 CFM at 125 PSI, 46.4 CFM at 150 PSI, and 41.7 CFM at 175 PSI, all from the same 15 HP motor and the same frame. Choosing 125 PSI buys about 25 percent more air than the 175 PSI build, which is the right trade whenever the tool list works at 90 to 100 PSI at the point of use, as most sanders, impact tools, spray guns and plasma torches do. Step up to 150 or 175 PSI only when a specific machine calls for it or a long run of undersized pipe eats the pressure on the way out, because header pressure you do not need is horsepower you pay for every hour the compressor runs.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 15 HP AS-B range the pressure, the mounting and the dryer all move independently. The \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TM\u003c\/a\u003e is the same compressor and the same tank without the dryer, at 776 lbs, and the \u003ca href=\"\/products\/abac-as-15-15-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-15253BM\u003c\/a\u003e is the bare base mount machine at 478 lbs for shops that already own a receiver. Moving up in pressure trades airflow: the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TMD\u003c\/a\u003e gives 46.4 CFM at 150 PSI and the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003eAS-15753TMD\u003c\/a\u003e gives 41.7 CFM at 175 PSI, both in the identical cabinet. If the tool list calls for more air at the same 125 PSI, the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-20253TMD\u003c\/a\u003e steps up to 20 HP and 60.6 CFM at 71 dBA. Pick on pressure first, then on CFM, then on whether the tank and dryer come in the package or get bought separately.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eAt 52.1 CFM this is a whole shop machine rather than a bench supply: a body shop running a booth alongside air tools, a cabinet or millwork shop on orbital sanders and nailers, a fabrication shop feeding a plasma table, or a small production line on pneumatic controls and instrument air. Dry air is the thread running through all of them. Paint, powder coat, plasma consumables and air logic fail in the same way when water reaches them, and here they are all fed from a discharge that has already passed through the dryer. The 131 gallon receiver gives the package room to ride out bursts of heavy demand without short cycling, and at 69 dBA it is quiet enough to sit near the point of use instead of in a dedicated compressor room.\u003c\/p\u003e\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\u003cp\u003eThe dryer and the receiver are already in the box, so what is left to decide is drainage, filtration and pipe. Put a \u003ca href=\"\/collections\/condensate-drains\"\u003econdensate drain\u003c\/a\u003e on both the tank and the dryer so the water they knock out actually leaves the system, add \u003ca href=\"\/collections\/air-filters\"\u003ecoalescing and particulate filtration\u003c\/a\u003e downstream if the air feeds paint or instruments, and run \u003ca href=\"\/collections\/aluminum-air-pipe\"\u003ealuminum compressed air pipe\u003c\/a\u003e so the distribution side does not put rust back into air you just dried. Keep an oil, oil filter and separator element set on the shelf and let the controller's programmed maintenance schedule tell you when they are due. See the rest of the \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full range of \u003ca href=\"\/collections\/fixed-speed-rotary-screw-air-compressors\"\u003efixed speed rotary screw air compressors\u003c\/a\u003e. Call us with your tool list and duty cycle and we will confirm sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67577765232915,"sku":"4152043930","price":12451.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-15-tmd.png?v=1790967821"},{"product_id":"abac-as-15-15-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor","title":"ABAC AS-15503TMD 15 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 150 PSI, 46.4 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-15503TMD is the all in one version of ABAC's 15 HP AS-B screw compressor set up for higher pressure: compressor, 131 gallon receiver and air dryer built onto a single frame and shipped as one machine. It delivers 46.4 CFM at a 150 PSI maximum and runs at 69 dBA on 208-230-460V three-phase power. Because the dryer is already plumbed and wired into the package, there is no second unit to size, site, pipe or power, and the air leaving the discharge is already dry. At 871 lbs in a 76 x 27 x 62 in footprint it occupies roughly the floor space of the tank alone.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AS-15503TMD (part number 4152043931)\u003c\/li\u003e\n\u003cli\u003eMotor: 15 HP\u003c\/li\u003e\n\u003cli\u003eAir delivery: 46.4 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated air dryer, factory piped and wired\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 871 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end with vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eEnergy efficient motor and digital controller with programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at free air delivery for the 10S to 20 HP range. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e\u003ch3\u003eWhy 150 PSI, and what it costs you\u003c\/h3\u003e\u003cp\u003ePressure and airflow trade against each other on the same air end. The 150 PSI build of this machine carries 46.4 CFM where the 125 PSI build carries 52.1 CFM, from identical hardware in an identical cabinet at the same 871 lbs. Buy the pressure only if a tool, a press, a clamp or a test stand genuinely needs it. If nothing on the floor asks for more than 125 PSI, the lower pressure build gives you about 12 percent more air for the same power draw. Where 150 PSI is the requirement, running it here rather than regulating down from a 175 PSI machine keeps the compressor off its least efficient operating point.\u003c\/p\u003e\u003ch3\u003eWhy the dryer belongs on the compressor\u003c\/h3\u003e\u003cp\u003eA rotary screw is rated for 100 percent duty, so it holds line pressure through a full shift instead of recovering between jobs. It also pushes warm, saturated air into the piping, and that water condenses out in the lines rather than in the compressor room. Drying at the source keeps condensate out of the distribution piping altogether instead of leaving traps, filters and drip legs downstream to catch it. In a paint booth, a powder coating line or a plasma table, that is the difference between a clean part and a reject.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 15 HP AS-B range the pressure, the mounting and the dryer all move independently. The \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TM\u003c\/a\u003e is the same compressor and the same tank without the dryer, at 776 lbs, and the \u003ca href=\"\/products\/abac-as-15-15-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-15503BM\u003c\/a\u003e is the bare base mount machine at 478 lbs for shops that already own a receiver. Moving on pressure trades airflow: the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TMD\u003c\/a\u003e gives 52.1 CFM at 125 PSI and the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003eAS-15753TMD\u003c\/a\u003e gives 41.7 CFM at 175 PSI, both in the identical cabinet. If the tool list calls for more air at this same 150 PSI, the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-20503TMD\u003c\/a\u003e steps up to 20 HP and 54 CFM at 71 dBA. Pick on pressure first, then on CFM, then on whether the tank and dryer come in the package or get bought separately.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003ePaint and finishing work, powder coating, plasma cutting, pneumatic controls and instrument air, press and clamp circuits that will not hold at 125 PSI, and any shop where moisture in the line shows up as a defect in the finished part. The 131 gallon receiver gives the machine room to ride out short bursts of heavy demand without short cycling, and at 69 dBA the package is quiet enough to sit near the point of use rather than in a dedicated compressor room.\u003c\/p\u003e\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\u003cp\u003eThe dryer and the receiver are already in the box, so what is left is drainage, filtration and pipe. Put a \u003ca href=\"\/collections\/condensate-drains\"\u003econdensate drain\u003c\/a\u003e on the tank and the dryer so the water they knock out actually leaves the system, add \u003ca href=\"\/collections\/air-filters\"\u003ecoalescing and particulate filtration\u003c\/a\u003e downstream if the air feeds paint or instruments, and run \u003ca href=\"\/collections\/aluminum-air-pipe\"\u003ealuminum compressed air pipe\u003c\/a\u003e so the distribution side does not put rust back into air you just dried. Size the piping for 46.4 CFM at the far end of the run, not at the compressor. See the rest of the \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e. Call us with your tool list and duty cycle and we will confirm sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67577765265683,"sku":"4152043931","price":12451.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-15-tmd_d04c97ae-b263-450c-b1e8-4f6e0a315e0f.png?v=1790967824"},{"product_id":"abac-as-15-15-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor","title":"ABAC AS-15753TMD 15 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 175 PSI, 41.7 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-15753TMD is the all in one, high pressure build of ABAC's 15 HP AS-B screw compressor: compressor, 131 gallon receiver and refrigerated air dryer assembled onto a single frame and shipped as one machine. It delivers 41.7 CFM at a 175 PSI maximum and runs at 69 dBA on 208-230-460V three-phase power. Because the dryer arrives already piped and wired into the package, there is no second unit to size, site, pipe or power, and the air leaving the discharge is already dry. At 871 lbs in a 76 x 27 x 62 in footprint the whole package occupies roughly the floor space of the tank alone.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AS-15753TMD (part number 4152043932)\u003c\/li\u003e\n\u003cli\u003eMotor: 15 HP\u003c\/li\u003e\n\u003cli\u003eAir delivery: 41.7 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer, factory piped and wired\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 871 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end with vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eEnergy efficient motor and digital controller with programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C, quoted at free air delivery for the 10S to 20 HP range. Noise measured per ISO 2151:2004 using ISO 9614\/2.\u003c\/em\u003e\u003c\/p\u003e\u003ch3\u003eBuilt for continuous duty\u003c\/h3\u003e\u003cp\u003eThe AS-B platform runs a fully integrated aluminum air end block with vertical oil separation, a design ABAC uses to hold down air loss and oil carryover over long run hours. A rotary screw is rated for 100 percent duty, so it holds line pressure through a full shift instead of recovering between jobs the way a piston machine does. The digital controller handles pressure setpoints, start and stop behavior and programmed maintenance intervals, so the machine looks after itself through the shift. Air delivery is rated to ISO 1217 Annex C and the sound level to ISO 2151, which means these figures compare directly against any other manufacturer quoting the same standards rather than a best case number.\u003c\/p\u003e\u003ch3\u003eWhy the dryer belongs on the compressor\u003c\/h3\u003e\u003cp\u003eA screw compressor pushes warm, saturated air into the piping, and that water condenses out in the lines rather than in the compressor room. Drying at the source keeps condensate out of the distribution piping altogether instead of leaving traps, filters and drip legs downstream to catch it. In a paint booth, a powder coating line or on a plasma table, that is the difference between a clean part and a reject. It also matters more at 175 PSI than at 125, because air compressed harder carries more moisture to drop out once it expands at the tool.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 15 HP AS-B range the pressure, the mounting and the dryer all move independently. This is the highest pressure build, and the trade is air delivery: 41.7 CFM at 175 PSI against 46.4 CFM from the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TMD\u003c\/a\u003e at 150 PSI and 52.1 CFM from the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TMD\u003c\/a\u003e at 125 PSI, all three in the identical cabinet at the same 871 lbs. Specify 175 PSI when a tool or a process genuinely needs the pressure, not as headroom, because every PSI of headroom is CFM you are not getting. If the air downstream is already treated, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-15753TM\u003c\/a\u003e is the same compressor and the same tank without the dryer at 776 lbs. Where a receiver is already installed, the \u003ca href=\"\/products\/abac-as-15-15-hp-base-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-15753BM base mount\u003c\/a\u003e is the bare machine at 478 lbs in a 37 x 28 x 40 in footprint. If the shop regularly asks for more than 41.7 CFM at this pressure, the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003eAS-20753TMD\u003c\/a\u003e steps up to 20 HP and 48.5 CFM at 71 dBA. Pick on pressure first, then on CFM, then on whether the tank and dryer come in the package or get bought separately.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003ePaint and finishing work, powder coating, plasma cutting, pneumatic controls and instrument air, and any shop where moisture in the line shows up as a defect in the finished part. The 175 PSI rating suits shops running higher pressure tooling, long distribution runs where line loss eats into working pressure, and processes specified above 150 PSI at the point of use. The 131 gallon receiver gives the machine room to ride out short bursts of heavy demand without short cycling, and at 69 dBA the package is quiet enough to sit near the point of use rather than in a dedicated compressor room.\u003c\/p\u003e\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\u003cp\u003eThe dryer and the receiver are already in the box, so what is left is drainage, filtration and pipe. Put a \u003ca href=\"\/collections\/condensate-drains\"\u003econdensate drain\u003c\/a\u003e on the tank and the dryer so the water they knock out actually leaves the system, add \u003ca href=\"\/collections\/air-filters\"\u003ecoalescing and particulate filtration\u003c\/a\u003e downstream if the air feeds paint or instruments, and run \u003ca href=\"\/collections\/aluminum-air-pipe\"\u003ealuminum compressed air pipe\u003c\/a\u003e so the distribution side does not put rust back into air you just dried. Part of the ABAC AS-B screw range from the Atlas Copco group. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and our wider range of \u003ca href=\"\/collections\/air-dryers\"\u003eair dryers\u003c\/a\u003e. Call us with your tool list and duty cycle and we will confirm sizing, connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67577765298451,"sku":"4152043932","price":12451.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-15-tmd_4deb74d0-9357-4e73-b411-da53534b8ad0.png?v=1790967830"},{"product_id":"abac-as-20-20-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor","title":"ABAC AS-20253TM 20 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 125 PSI, 60.6 CFM, 71 dBA","description":"\u003cp\u003eThe ABAC AS-20253TM is the 125 PSI build of the 20 HP machine in the AS-B screw range, delivered on a 131 gallon horizontal receiver as a single assembly. It puts out 60.6 CFM at a 125 PSI maximum and runs at 71 dBA. Tank mount is the configuration to buy when there is no receiver already in the plant: compressor, tank and controls arrive piped and wired together, so installation comes down to setting it on the floor, bringing power to it and connecting the air line. At 813 lbs in a 76 x 27 x 62 in footprint it takes roughly the floor space of a workbench. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-20253TM (part number 4152043924)\u003c\/li\u003e\n\u003cli\u003eMotor: 20 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 60.6 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 71 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 813 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access for programmed maintenance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops using air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end is built around a state of the art design that limits air loss, and ABAC pairs it with an energy efficient motor and a digital controller, so the operating menus and the service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 131 gallon receiver underneath this one is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow and mounting all move independently. At 125 PSI this machine is the airflow build of the 20 HP frame. The \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-20503TM\u003c\/a\u003e is the same compressor set for 150 PSI at 54 CFM, and the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-20753TM\u003c\/a\u003e goes to 175 PSI and 48.5 CFM. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow. Stepping down in power, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-15253TM\u003c\/a\u003e gives 52.1 CFM at the same 125 PSI and 69 dBA, which is the machine to compare against when the extra 8.5 CFM here is not yet needed. If you already own a receiver, the same air end comes as the \u003ca href=\"\/products\/abac-as-20-20-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-20253BM\u003c\/a\u003e base mount at 516 lbs on a 37 x 28 x 40 in footprint. If you want drying built in, the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-20253TMD\u003c\/a\u003e is this exact machine with the refrigerated dryer already mounted and piped. Stepping up again, the \u003ca href=\"\/products\/abac-as-25-25-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-25253TMD\u003c\/a\u003e carries 98.9 CFM.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, larger automotive and fleet service shops, tire and truck bays, cabinet and woodworking shops, plasma and laser tables, packaging lines, and multi bay operations adding a blast cabinet or a finishing booth. At 60.6 CFM it will keep several bays of air ratchets, sanders and continuous blow off fed through a full shift without the line pressure sagging. The tank mount build is the one to buy for a new installation, or for a shop replacing a worn piston compressor outright, because it takes receiver sizing and tank piping out of the job.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals. Air leaving any screw carries moisture, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 60.6 CFM the \u003ca href=\"\/products\/abac-cool-65-refrigerated-air-dryer-115v\"\u003eABAC COOL 65\u003c\/a\u003e is the minimum size and the \u003ca href=\"\/products\/abac-cool-75-refrigerated-air-dryer-115v\"\u003eCOOL 75\u003c\/a\u003e gives useful headroom; both run on 115V, so they sit beside the compressor without new wiring. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCFM measured per ISO 1217 Annex C. Noise measured per ISO 2151:2004 using ISO 9614\/2 (sound intensity method).\u003c\/em\u003e\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67578757742867,"sku":"4152043924","price":11254.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-20253tm.png?v=1791389315"},{"product_id":"abac-as-20-20-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor","title":"ABAC AS-20503TM 20 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 150 PSI, 54 CFM, 71 dBA","description":"\u003cp\u003eThe ABAC AS-20503TM is the 150 PSI, 131 gallon tank mount build of the 20 HP machine in the AS-B screw range. It delivers 54 CFM free air delivery at a 150 PSI maximum and runs at 71 dBA. The 150 PSI setting is the middle of the three builds on this frame, and it is the one to specify when a clamp circuit, a plant header or a long pipe run needs more than the usual 125 PSI but nothing on the floor genuinely calls for 175. Because the air end, the controls and the receiver ship as one assembly, installation comes down to setting it in place, landing power and tying into the air line. At 813 lbs on a 76 x 27 x 62 in footprint it takes roughly the floor space of a workbench. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-20503TM (part number 4152043925)\u003c\/li\u003e\n\u003cli\u003eMotor: 20 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 54 CFM free air delivery\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 71 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 813 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access for optimizing operating performance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops using air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end is built around a fully integrated aluminum block and eco-friendly vertical oil separation, paired with an energy efficient motor and a digital controller, so the operating menus and the service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 131 gallon receiver underneath this one is there to prevent.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAcross the AS-B range pressure, airflow and mounting move independently on the same chassis. The \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-20253TM\u003c\/a\u003e is this identical 813 lb package set for 125 PSI, trading pressure for airflow at 60.6 CFM, and the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-20753TM\u003c\/a\u003e goes to 175 PSI and 48.5 CFM. Buy pressure only to the level your highest tool actually needs, because every step up costs airflow. One size down, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-15503TM\u003c\/a\u003e carries 46.4 CFM at the same 150 PSI on the same tank, which is the machine to compare against when the extra 7.6 CFM here is not yet needed. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-20-20-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-20503BM\u003c\/a\u003e is the bare 516 lb base mount at the same pressure on a 37 x 28 x 40 in footprint. If you want drying built in, the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-20503TMD\u003c\/a\u003e is this exact machine with the refrigerated dryer already mounted and piped. And if volume rather than pressure is the constraint, the quieter \u003ca href=\"\/products\/abac-as-20s-20-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-20S503BM\u003c\/a\u003e air end delivers 78 CFM at 67 dBA from the same 20 HP rating.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, larger automotive and fleet service shops, tire and truck bays, cabinet and woodworking shops, plasma and laser tables, packaging lines, pneumatic controls and conveying, and multi bay operations adding a blast cabinet or a finishing booth. At 54 CFM it will keep several bays of air ratchets, sanders and continuous blow off fed through a shift without the line pressure sagging. The tank mount build is the one to buy for a new installation, or for a shop replacing a worn piston compressor outright, because it takes receiver sizing and tank piping out of the job.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals. Air leaving any screw carries moisture, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 54 CFM the \u003ca href=\"\/products\/abac-cool-65-refrigerated-air-dryer-115v\"\u003eABAC COOL 65\u003c\/a\u003e is the sensible match and the \u003ca href=\"\/products\/abac-cool-75-refrigerated-air-dryer-115v\"\u003eCOOL 75\u003c\/a\u003e gives headroom for growth; both run on 115V, so they sit beside the compressor without new wiring. See the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67578800865555,"sku":"4152043925","price":11254.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-20503tm.png?v=1791400034"},{"product_id":"abac-as-20-20-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor","title":"ABAC AS-20753TM 20 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount, 175 PSI, 48.5 CFM, 71 dBA","description":"\u003cp\u003eThe ABAC AS-20753TM is the 175 PSI, 131 gallon tank mount build of the 20 HP machine in the AS-B screw range. It delivers 48.5 CFM free air delivery at a 175 PSI maximum and runs at 71 dBA. This is the highest pressure of the three builds on this frame, and it is the one to specify when a tool, a clamp circuit or a process genuinely needs 175 PSI at the point of use rather than as headroom. Because the air end, the controls and the receiver ship as one assembly, installation comes down to setting it in place, landing power and tying into the air line. At 818 lbs on a 76 x 27 x 62 in footprint it takes roughly the floor space of a workbench. Power is 208-230-460V three-phase.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AS-20753TM (part number 4152043926)\u003c\/li\u003e\n\u003cli\u003eMotor: 20 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 48.5 CFM free air delivery\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 71 dBA\u003c\/li\u003e\n\u003cli\u003eMounting: tank mount on a 131 gallon air receiver\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 818 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum air end block\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with menu driven access for optimizing operating performance\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. That is the reason shops using air most of the day move off a reciprocating machine that is cycling hard, running hot and filling the room with noise. The AS-B air end is built around a fully integrated aluminum block and eco-friendly vertical oil separation, paired with an energy efficient motor and a digital controller, so the operating menus and the service intervals sit on the panel rather than on a clipboard. The trade is that a screw dislikes short cycling, which is exactly what the 131 gallon receiver underneath this one is there to prevent.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eAcross the AS-B range pressure, airflow and mounting move independently on the same chassis, and pressure is bought with airflow. This machine is the 175 PSI end of that trade at 48.5 CFM. The \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-20503TM\u003c\/a\u003e is the same package set for 150 PSI and 54 CFM, and the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-20253TM\u003c\/a\u003e gives 60.6 CFM at 125 PSI. Before specifying this one, check the pressure rating of the highest tool on the floor, because stepping down to 150 PSI buys 5.5 more CFM from the same 20 HP motor. If you already own a receiver, the \u003ca href=\"\/products\/abac-as-20-20-hp-base-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-20753BM\u003c\/a\u003e is the bare 520 lb base mount at the same pressure and airflow on a 37 x 28 x 40 in footprint. If you want drying built in, the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003eAS-20753TMD\u003c\/a\u003e is this exact machine with the refrigerated dryer already mounted and piped. One size down, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-15753TM\u003c\/a\u003e holds 175 PSI at 41.7 CFM on the same tank, which is the machine to compare against when the extra 6.8 CFM here is not yet needed.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction and fabrication floors running high pressure clamping or forming, automotive and fleet service bays, tire and truck shops, plasma and laser tables, packaging lines, pneumatic controls and conveying, and long plant headers where pipe run losses eat into delivered pressure. At 48.5 CFM and 175 PSI it suits the shop whose constraint is pressure at the tool rather than raw volume. The tank mount build is the one to buy for a new installation, or for a shop replacing a worn piston compressor outright, because it takes receiver sizing and tank piping out of the job.\u003c\/p\u003e\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\u003cp\u003eGive the cabinet clear air on the cooling side, keep it out of a hot corner, and run it on its own circuit sized to the motor nameplate. Oil, oil filter and separator element are the service items, and the digital controller tracks the intervals. Air leaving any screw carries moisture, so if it goes to paint, tires, pneumatic controls or anything that hates water, put a refrigerated dryer behind it. At 48.5 CFM the \u003ca href=\"\/products\/abac-cool-65-refrigerated-air-dryer-115v\"\u003eABAC COOL 65\u003c\/a\u003e is the sensible match and the \u003ca href=\"\/products\/abac-cool-75-refrigerated-air-dryer-115v\"\u003eCOOL 75\u003c\/a\u003e gives headroom for growth; both run on 115V, so they sit beside the compressor without new wiring.\u003c\/p\u003e\u003cp\u003eSee the rest of our \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e and the full \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryer\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67579057013011,"sku":"4152043926","price":11254.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-20753tm.png?v=1790975857"},{"product_id":"abac-as-20-20-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor","title":"ABAC AS-20253TMD 20 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 125 PSI, 60.6 CFM, 71 dBA","description":"\u003cp\u003eThe ABAC AS-20253TMD is a complete 20 HP compressed air station on one base: a rotary screw compressor, a 131 gallon air receiver and an integrated refrigerated dryer, mounted and plumbed together at the factory. It delivers 60.6 CFM at 125 PSI and runs at 71 dBA. Because the three pieces arrive matched and wired as one unit, installation comes down to setting it in place, bringing 208-230-460V three-phase power to it and connecting your air line. There is no separate dryer to size, site, pipe and find floor space for.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AS-20253TMD (part number 4152043933)\u003c\/li\u003e\n\u003cli\u003eMotor: 20 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 60.6 CFM\u003c\/li\u003e\n\u003cli\u003eWorking pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 71 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003e3-stage vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller\u003c\/li\u003e\n\u003cli\u003eDimensions: 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eWeight: 908 lbs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 20 HP range the choice is really about how much of the air system you want delivered as one piece. The \u003ca href=\"\/products\/abac-as-20-20-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-20253BM base mount\u003c\/a\u003e is the compressor alone at 516 lbs in a 37 x 28 x 40 in footprint, for a shop that already has a receiver and a dryer. The \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-20253TM\u003c\/a\u003e adds the receiver at 813 lbs. This TMD package adds the dryer on top of that at 908 lbs on the same 76 x 27 x 62 in base, so the extra 95 lbs buys dry air without a second machine on the floor. If your tools and controls need a higher line pressure, the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-20503TMD\u003c\/a\u003e is the same package rated 54 CFM at 150 PSI, trading airflow for pressure. On airflow, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e15 HP AS-15253TMD\u003c\/a\u003e sits below it at 52.1 CFM and the \u003ca href=\"\/products\/abac-as-25-25-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e25 HP AS-25253TMD\u003c\/a\u003e above it at 98.9 CFM.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction and fabrication floors, machine shops running several CNC cells, automotive and fleet service bays, tire and truck shops, plasma cutting, and spray finishing or powder coating work where water in the air line turns into runs, fisheyes and sticking air logic. Drying the air at the compressor keeps condensate out of the distribution piping instead of leaving it for traps and filters downstream to catch, which matters most on long runs of overhead pipe where the air cools on its way to the tool.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003ePlan the electrical for a 20 HP three-phase motor and size the disconnect and conductors to the nameplate. Leave clearance on the cooling air side and keep the room ventilated, because a refrigerated dryer rejects heat into the same space the compressor does. Oil, oil filter and the separator element are the recurring service items on a screw, so keep a set on the shelf rather than ordering them when the controller asks. A rotary screw is built for continuous duty, so this machine is meant to run through a full shift and hold line pressure rather than cycle on and off the way a piston compressor does.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B screw range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e, built around a fully integrated air end, 3-stage vertical oil separation and an intuitive digital controller. Compare the rest of the \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e, or browse \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e if you are adding drying capacity to a compressor you already own.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67579085914387,"sku":"4152043933","price":15127.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-20-tmd.png?v=1790976641"},{"product_id":"abac-as-20-20-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor","title":"ABAC AS-20503TMD 20 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 150 PSI, 54 CFM, 71 dBA","description":"\u003cp\u003eThe ABAC AS-20503TMD is a complete 20 HP compressed air station on one base: a rotary screw compressor, a 131 gallon air receiver and an integrated refrigerated dryer, mounted, piped and wired together at the factory. It delivers 54 CFM at 150 PSI and runs at 71 dBA. Because the three pieces arrive matched as one unit, installation comes down to setting it in place, bringing 208-230-460V three-phase power to it and connecting the air line. There is no separate dryer to size, site, pipe and find floor space for.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AS-20503TMD (part number 4152043934)\u003c\/li\u003e\n\u003cli\u003eMotor: 20 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 54 CFM\u003c\/li\u003e\n\u003cli\u003eWorking pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 71 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eVertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with programmed maintenance menus\u003c\/li\u003e\n\u003cli\u003eDimensions: 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eWeight: 908 lbs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhy the 150 PSI build\u003c\/h3\u003e\u003cp\u003ePressure and airflow trade against each other on the same 20 HP motor. Built identically, the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e125 PSI AS-20253TMD\u003c\/a\u003e carries 60.6 CFM and the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003e175 PSI AS-20753TMD\u003c\/a\u003e carries 48.5 CFM. The 150 PSI machine is the middle choice, and it is the right one when tooling, press equipment or a long run of distribution piping needs headroom above a 125 PSI compressor without needing a full 175 PSI. Regulating down from a higher setting costs energy, so buy the pressure the plant actually works at rather than the largest number on the page.\u003c\/p\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 20 HP 150 PSI range the question is how much of the air system arrives as one piece. The \u003ca href=\"\/products\/abac-as-20-20-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-20503BM base mount\u003c\/a\u003e is the compressor alone at 516 lbs in a 37 x 28 x 40 in footprint, for a shop that already owns a receiver and a dryer. The \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-20503TM\u003c\/a\u003e adds the receiver at 813 lbs. This TMD package adds the dryer on top of that at 908 lbs on the same 76 x 27 x 62 in base, so the extra 95 lbs buys dry air without a second machine on the floor. On airflow, the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e15 HP AS-15503TMD\u003c\/a\u003e sits below it at 46.4 CFM and 69 dBA, and the \u003ca href=\"\/products\/abac-as-25-25-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e25 HP AS-25503TMD\u003c\/a\u003e above it at 92.2 CFM.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eProduction and fabrication floors, machine shops running several CNC cells, automotive and fleet service bays, tire and truck shops, plasma cutting, pneumatic controls and air logic, and spray finishing or powder coating work where water in the air line turns into runs, fisheyes and sticking valves. Drying the air at the compressor keeps condensate out of the distribution piping instead of leaving it for traps and filters downstream to catch, which matters most on long overhead runs where the air cools on its way to the tool.\u003c\/p\u003e\u003ch3\u003eInstallation and service notes\u003c\/h3\u003e\u003cp\u003eSize the disconnect and the conductors to the motor nameplate for a 20 HP three-phase load, and confirm which of the 208, 230 or 460 volt taps the machine is wired for before energizing it. Leave clearance on the cooling air side and keep the room ventilated, because the refrigerated dryer rejects heat into the same space the compressor does. Oil, oil filter and the separator element are the recurring service items on a screw, so keep a set on the shelf rather than ordering them when the controller asks for them. A rotary screw is built for continuous duty, so this machine is meant to run through a full shift and hold line pressure rather than cycle on and off the way a piston compressor does.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B screw range from the \u003ca href=\"https:\/\/aircompressorstore.com\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e, built around a fully integrated aluminum block air end, vertical oil separation technology and an energy efficient motor. Air delivery on the 20 HP models is quoted as free air delivery and measured to ISO 1217 Annex C, and the noise figure is measured to ISO 2151:2004 using ISO 9614\/2. Compare the rest of the \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e, or browse \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e if you are adding drying capacity to a compressor you already own.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67579110523155,"sku":"4152043934","price":15127.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-20-tmd_a27991a2-6374-4181-9295-7abd3751c748.png?v=1790977332"},{"product_id":"abac-as-20-20-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor","title":"ABAC AS-20753TMD 20 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 175 PSI, 48.5 CFM, 71 dBA","description":"\u003cp\u003eThe ABAC AS-20753TMD is a complete 20 HP compressed air station on one base: a rotary screw compressor, a 131 gallon air receiver and an integrated refrigerated dryer, mounted and plumbed together at the factory. It delivers 48.5 CFM at 175 PSI and runs at 71 dBA on 208-230-460V three-phase power. This is the highest pressure build in the 20 HP tank mount with dryer family, specified when something on the floor genuinely needs 175 PSI at the point of use rather than 125 or 150.\u003c\/p\u003e\u003ch3\u003eKey specifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: AS-20753TMD (part number 4152043935)\u003c\/li\u003e\n\u003cli\u003eMotor: 20 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 48.5 CFM\u003c\/li\u003e\n\u003cli\u003eWorking pressure: 175 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 71 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eVertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eDigital controller with programmed maintenance\u003c\/li\u003e\n\u003cli\u003eDimensions: 76 x 27 x 62 in\u003c\/li\u003e\n\u003cli\u003eWeight: 913 lbs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eHow it compares\u003c\/h3\u003e\u003cp\u003eWithin the 20 HP AS tank mount with dryer family the motor rating stays the same and pressure is traded against flow. This 175 PSI build gives 48.5 CFM; the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003e150 PSI AS-20503TMD\u003c\/a\u003e gives 54 CFM and the \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003e125 PSI AS-20253TMD\u003c\/a\u003e gives 60.6 CFM, all on the same receiver at 71 dBA. Specify 175 PSI when a tool or process requires the pressure rather than as headroom, because every PSI above what the tools need costs flow. The package matters as much as the pressure. The \u003ca href=\"\/products\/abac-as-20-20-hp-base-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-20753BM base mount\u003c\/a\u003e is the compressor alone at 520 lbs in a 37 x 28 x 40 in footprint, for a shop that already has a receiver and a dryer. The \u003ca href=\"\/products\/abac-as-20-20-hp-131-gallon-tank-mount-175-psi-rotary-screw-air-compressor\"\u003eAS-20753TM\u003c\/a\u003e adds the receiver at 818 lbs, and this TMD build adds the dryer on top of that at 913 lbs on the same 76 x 27 x 62 in base, so the extra 95 lbs buys dry air without a second machine taking floor space. If the shop runs short of air rather than pressure, the \u003ca href=\"\/products\/abac-as-20s-20-hp-132-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-20S503TMD\u003c\/a\u003e delivers 78 CFM at 150 PSI and a quieter 67 dBA from the same 20 HP rating. A step down at the same pressure is the \u003ca href=\"\/products\/abac-as-15-15-hp-131-gallon-tank-mount-dryer-175-psi-rotary-screw-air-compressor\"\u003e15 HP AS-15753TMD\u003c\/a\u003e at 41.7 CFM.\u003c\/p\u003e\u003ch3\u003eTypical applications\u003c\/h3\u003e\u003cp\u003eSpray finishing and powder coating, plasma cutting, sandblasting, automotive and fleet service bays, tire and truck shops, pneumatic controls and production assembly, and any shop where a tool or process genuinely needs 175 PSI at the point of use. Drying the air at the compressor keeps condensate out of the distribution piping instead of leaving it for traps and filters downstream to catch, which is what otherwise turns up as runs in a finish, fouling on a plasma torch tip, or water in a blast pot. It matters most on long runs of overhead pipe, where the air cools on its way to the tool and drops its moisture at the worst possible place.\u003c\/p\u003e\u003ch3\u003eInstallation and service\u003c\/h3\u003e\u003cp\u003ePlan the electrical for a 20 HP three-phase motor and size the disconnect and conductors to the nameplate. Leave clearance on the cooling air side and keep the room ventilated and above freezing, because a refrigerated dryer rejects heat into the same space the compressor does. A rotary screw is built for continuous duty, so it holds steady line pressure through a full shift rather than cycling on and off the way a piston compressor does. Oil, oil filter and the separator element are the recurring service items, and keeping a set on the shelf avoids a shutdown waiting on parts. Drain the receiver and check the dryer condensate drain on the same schedule.\u003c\/p\u003e\u003cp\u003ePart of the ABAC AS-B screw range from the \u003ca href=\"\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e, built around a fully integrated aluminum block air end, vertical oil separation technology and an energy efficient motor. Compare the rest of the \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressors\u003c\/a\u003e, or browse \u003ca href=\"\/collections\/refrigerated-air-dryers\"\u003erefrigerated air dryers\u003c\/a\u003e if you are adding drying capacity to a compressor you already own.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67615559680275,"sku":"4152043935","price":15127.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-20753tmd.png?v=1791215830"},{"product_id":"abac-as-25-25-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor","title":"ABAC AS-25253TMD 25 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 125 PSI, 98.9 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-25253TMD is a complete 25 HP compressed air station on one skid: a rotary screw air end, a 131 gallon air receiver and an integrated refrigerated dryer, mounted, wired and plumbed together at the factory. It delivers 98.9 CFM at a 125 PSI maximum and runs at 69 dBA. There is no separate tank or dryer to size, site and pipe, so installation comes down to setting it in place, landing one electrical connection and connecting your air line. Assembled it measures 75 x 31 x 72 in and weighs 1330 lbs. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-25253TMD (part number 4152028469)\u003c\/li\u003e\n\u003cli\u003eMotor: 25 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 98.9 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 1330 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 75 x 31 x 72 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eLow noise and vibration, up to 10 percent lower carbon footprint than the range it replaces\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy 125 PSI, and what it buys you\u003c\/h3\u003e\n\u003cp\u003ePressure and flow trade against each other on the same air end. At 125 PSI this machine gives 98.9 CFM; the 150 PSI build of the identical package gives 92.2 CFM. That is close to 7 CFM of airflow recovered by not asking for the extra 25 PSI, and you keep it in energy every hour the compressor runs. If every drop in the shop is regulated down to 90 or 100 PSI anyway, 125 PSI is the right buy and the cheaper one to own. Step up to 150 PSI only when something real needs it: press and clamp circuits, higher pressure tooling, or a long distribution run where line loss eats into delivered pressure before the air reaches the tool.\u003c\/p\u003e\n\u003ch3\u003eWhat the tank and dryer package changes\u003c\/h3\u003e\n\u003cp\u003eEvery rotary screw sends warm, saturated air downstream, and that water is what rusts piping, freezes air logic, pits tooling and ruins a paint finish. Solving it piecemeal means sizing a receiver, buying a dryer, finding floor space for both, then wiring and plumbing them to the compressor. On the TMD build all three arrive as one matched assembly: the receiver sits under the compressor, the dryer is mounted and wired with it, and the footprint stays 75 x 31 in rather than three separate machines spread along a wall. The cost is height and weight, 72 in tall and 1330 lbs, so check door clearance and floor loading before delivery. If a filter stack and an oil water separator are also going in, plan their wall space when you lay the machine out.\u003c\/p\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. At 25 HP that difference is the whole point: this is a machine for a shop drawing air most of the day, not one that tops up a receiver now and then. A screw dislikes short cycling, which is part of why the matched receiver matters, and it wants a demand pattern that keeps it loaded.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eWithin the AS-B range the choices around this machine are pressure, mounting and dryer. The \u003ca href=\"\/products\/abac-as-25-25-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-25503TMD\u003c\/a\u003e is the same package set for 150 PSI, trading flow for pressure at 92.2 CFM in an identical cabinet at the same 1330 lbs. If you already own a correctly sized receiver, the \u003ca href=\"\/products\/abac-as-25-25-hp-base-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-25253BMD\u003c\/a\u003e is the same 98.9 CFM air end and dryer without the tank, at 831 lbs and 55 x 31 x 49 in, and the \u003ca href=\"\/products\/abac-as-25-25-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-25253BM\u003c\/a\u003e drops the dryer as well at 723 lbs and 44 x 31 x 49 in. Either side on horsepower, the \u003ca href=\"\/products\/abac-as-20s-20-hp-132-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-20S253TMD\u003c\/a\u003e gives 81.9 CFM at a quieter 67 dBA and 1297 lbs, and the \u003ca href=\"\/products\/abac-as-30-30-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-30253TMD\u003c\/a\u003e gives 114.1 CFM at 70 dBA and 1365 lbs in the same 75 x 31 x 72 in footprint. At 98.9 CFM the AS-25 is the machine for a shop that has outgrown 20 HP but does not need a full 30 HP service.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, machine shops running several CNC cells, automotive and fleet service bays, tire and truck shops, plasma tables, packaging lines, sandblasting, and spray finishing or powder coating where moisture in the line spoils tools, air logic or finish quality. At 98.9 CFM it will carry a bank of air ratchets and sanders, a continuous blow off, a blast cabinet, or several cells drawing at once through a full shift. Drying the air at the compressor keeps condensate out of the distribution piping instead of leaving it for traps and filters downstream to catch.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet clear air on the cooling side, keep the room out of the heat, and run the unit on its own circuit sized to the motor nameplate; at 25 HP the electrical install is worth planning before the machine arrives. Oil, oil filter and separator element are the service items. Behind the dryer, a coalescing filter protects paint and instrument air, and a condensate drain plus an oil water separator keeps the water the dryer pulls out of your floor and out of the drain line. See our \u003ca href=\"\/collections\/coalescing-air-filters\"\u003ecoalescing air filters\u003c\/a\u003e, \u003ca href=\"\/collections\/condensate-drains\"\u003econdensate drains\u003c\/a\u003e and \u003ca href=\"\/collections\/oil-water-separator\"\u003eoil water separators\u003c\/a\u003e, or browse the full \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressor\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67619047244051,"sku":"4152028469","price":21060.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-25-tank-mount-dryer-rotary-screw-air-compressor.png?v=1791518961"},{"product_id":"abac-as-25-25-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor","title":"ABAC AS-25503TMD 25 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 150 PSI, 92.2 CFM, 69 dBA","description":"\u003cp\u003eThe ABAC AS-25503TMD is a complete 25 HP compressed air station on one skid: a rotary screw air end, a 131 gallon air receiver and an integrated refrigerated dryer, mounted, wired and plumbed together at the factory. It delivers 92.2 CFM at a 150 PSI maximum and runs at 69 dBA. There is no separate tank or dryer to size, site and pipe, so installation comes down to setting it in place, landing one electrical connection and connecting your air line. Assembled it measures 75 x 31 x 72 in and weighs 1330 lbs. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-25503TMD (part number 4152028470)\u003c\/li\u003e\n\u003cli\u003eMotor: 25 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 92.2 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 69 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 1330 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 75 x 31 x 72 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eLow noise and vibration, up to 10 percent lower carbon footprint than the range it replaces\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy 150 PSI, and what it costs you\u003c\/h3\u003e\n\u003cp\u003ePressure and flow trade against each other on the same air end. At 150 PSI this machine gives 92.2 CFM; the 125 PSI build of the identical package gives 98.9 CFM. You are spending close to 7 CFM of airflow, and the energy behind it every hour the compressor runs, to buy the extra 25 PSI. Buy it when something real needs the pressure: press and clamp circuits, higher pressure tooling, a shop that runs at 120 PSI at the drop rather than 90, or a long distribution run where line loss eats into delivered pressure before the air reaches the tool. If every drop is regulated down to 90 or 100 PSI anyway, the 125 PSI build is the better machine and the cheaper one to own.\u003c\/p\u003e\n\u003ch3\u003eWhat the tank and dryer package changes\u003c\/h3\u003e\n\u003cp\u003eEvery rotary screw sends warm, saturated air downstream, and that water is what rusts piping, freezes air logic, pits tooling and ruins a paint finish. Solving it piecemeal means sizing a receiver, buying a dryer, finding floor space for both, then wiring and plumbing them to the compressor. On the TMD build all three arrive as one matched assembly: the receiver sits under the compressor, the dryer is mounted and wired with it, and the footprint stays 75 x 31 in rather than three separate machines spread along a wall. The cost is height and weight, 72 in tall and 1330 lbs, so check door clearance and floor loading before delivery. If a filter stack and an oil water separator are also going in, plan their wall space when you lay the machine out.\u003c\/p\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. At 25 HP that difference is the whole point: this is a machine for a shop drawing air most of the day, not one that tops up a receiver now and then. A screw dislikes short cycling, which is part of why the matched receiver matters, and it wants a demand pattern that keeps it loaded.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eWithin the AS-B range the choices around this machine are pressure, mounting and dryer. The \u003ca href=\"\/products\/abac-as-25-25-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-25253TMD\u003c\/a\u003e is the same package set for 125 PSI, trading pressure for flow at 98.9 CFM in an identical cabinet at the same 1330 lbs. If you already own a correctly sized receiver, the \u003ca href=\"\/products\/abac-as-25-25-hp-base-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-25503BMD\u003c\/a\u003e is the same 92.2 CFM air end and dryer without the tank, at 831 lbs and 55 x 31 x 49 in, and the \u003ca href=\"\/products\/abac-as-25-25-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-25503BM\u003c\/a\u003e drops the dryer as well at 723 lbs and 44 x 31 x 49 in. Either side on horsepower at the same 150 PSI, the \u003ca href=\"\/products\/abac-as-20s-20-hp-132-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-20S503TMD\u003c\/a\u003e gives 78 CFM at a quieter 67 dBA and 1297 lbs, and the \u003ca href=\"\/products\/abac-as-30-30-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-30503TMD\u003c\/a\u003e gives 103.1 CFM at 70 dBA and 1365 lbs in the same 75 x 31 x 72 in footprint. At 92.2 CFM the AS-25 is the machine for a shop that has outgrown 20 HP but does not need a full 30 HP service.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, machine shops running several CNC cells, automotive and fleet service bays, tire and truck shops, plasma tables, packaging lines, sandblasting, and spray finishing or powder coating where moisture in the line spoils tools, air logic or finish quality. The 150 PSI rating suits shops where the distribution run is long, where press and clamp circuits sit on the same system as handheld tools, or where a 125 PSI machine has been struggling to hold pressure at the far end of the building. At 92.2 CFM it will carry a bank of air ratchets and sanders, a continuous blow off, a blast cabinet, or several cells drawing at once through a full shift. Drying the air at the compressor keeps condensate out of the distribution piping instead of leaving it for traps and filters downstream to catch.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet clear air on the cooling side, keep the room out of the heat, and run the unit on its own circuit sized to the motor nameplate; at 25 HP the electrical install is worth planning before the machine arrives. Oil, oil filter and separator element are the service items. Behind the dryer, a coalescing filter protects paint and instrument air, and a condensate drain plus an oil water separator keeps the water the dryer pulls out of your floor and out of the drain line. See our \u003ca href=\"\/collections\/coalescing-air-filters\"\u003ecoalescing air filters\u003c\/a\u003e, \u003ca href=\"\/collections\/condensate-drains\"\u003econdensate drains\u003c\/a\u003e and \u003ca href=\"\/collections\/oil-water-separator\"\u003eoil water separators\u003c\/a\u003e, or browse the full \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressor\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67619422535955,"sku":"4152028470","price":21059.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-25-tank-mount-dryer-150-psi-rotary-screw-air-compressor.png?v=1791522564"},{"product_id":"abac-as-30-30-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor","title":"ABAC AS-30253TMD 30 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 125 PSI, 114.1 CFM, 70 dBA","description":"\u003cp\u003eThe ABAC AS-30253TMD is a complete 30 HP compressed air station on one skid: a rotary screw air end, a 131 gallon air receiver and an integrated refrigerated dryer, mounted, wired and plumbed together at the factory. It delivers 114.1 CFM at a 125 PSI maximum and runs at 70 dBA. There is no separate tank or dryer to size, site and pipe, so installation comes down to setting it in place, landing one electrical connection and connecting your air line. Assembled it measures 75 x 31 x 72 in and weighs 1365 lbs. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-30253TMD (part number 4152028471)\u003c\/li\u003e\n\u003cli\u003eMotor: 30 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 114.1 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 125 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 70 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 1365 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 75 x 31 x 72 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eEco-friendly vertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the Atlas Copco group\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy 125 PSI, and what it buys you\u003c\/h3\u003e\n\u003cp\u003ePressure and flow trade against each other on the same air end. At 125 PSI this machine gives 114.1 CFM; the 150 PSI build of the identical package gives 103.1 CFM. That is 11 CFM of airflow recovered by not asking for the extra 25 PSI, and you keep it in energy every hour the compressor runs. If every drop in the shop is regulated down to 90 or 100 PSI anyway, 125 PSI is the right buy and the cheaper one to own. Step up to 150 PSI only when something real needs it: press and clamp circuits, higher pressure tooling, or a long distribution run where line loss eats into delivered pressure before the air reaches the tool.\u003c\/p\u003e\n\u003ch3\u003eWhat the tank and dryer package changes\u003c\/h3\u003e\n\u003cp\u003eEvery rotary screw sends warm, saturated air downstream, and that water is what rusts piping, freezes air logic, pits tooling and ruins a paint finish. Solving it piecemeal means sizing a receiver, buying a dryer, finding floor space for both, then wiring and plumbing them to the compressor. On the TMD build all three arrive as one matched assembly: the receiver sits under the compressor, the dryer is mounted and wired with it, and the footprint stays 75 x 31 in rather than three separate machines spread along a wall. The cost is height and weight, 72 in tall and 1365 lbs, so check door clearance and floor loading before delivery. If a filter stack and an oil water separator are also going in, plan their wall space when you lay the machine out.\u003c\/p\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. At 30 HP that difference is the whole point: this is a machine for a plant drawing air most of the day, not one that tops up a receiver now and then. A screw dislikes short cycling, which is part of why the matched receiver matters, and it wants a demand pattern that keeps it loaded.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eAt 114.1 CFM this is the highest flow in the AS-B tank mount range, the machine a plant steps up to when added bays, a blast cabinet or a continuous process leave a smaller compressor running loaded almost all the time. The \u003ca href=\"\/products\/abac-as-30-30-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-30503TMD\u003c\/a\u003e is the same package set for 150 PSI, trading flow for pressure at 103.1 CFM in an identical cabinet at the same 1365 lbs. If you already own a correctly sized receiver, the \u003ca href=\"\/products\/abac-as-30-30-hp-base-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-30253BMD\u003c\/a\u003e is the same 114.1 CFM air end and dryer without the tank, at 867 lbs and 55 x 31 x 49 in, and the \u003ca href=\"\/products\/abac-as-30-30-hp-base-mount-125-psi-rotary-screw-air-compressor\"\u003eAS-30253BM\u003c\/a\u003e drops the dryer as well at 759 lbs and 44 x 31 x 49 in. One step down on horsepower, the \u003ca href=\"\/products\/abac-as-25-25-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-25253TMD\u003c\/a\u003e gives 98.9 CFM at a quieter 69 dBA and 1330 lbs in the same 75 x 31 x 72 in footprint. If 114.1 CFM is already close to your measured demand, buy the headroom here rather than running a 25 HP machine loaded continuously.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, machine shops running several CNC cells, automotive and fleet service bays, tire and truck shops, plasma tables, packaging lines, sandblasting, and spray finishing or powder coating where moisture in the line spoils tools, air logic or finish quality. At 114.1 CFM it will carry a bank of air ratchets and sanders, a continuous blow off, a blast cabinet, or several cells drawing at once through a full shift. Drying the air at the compressor keeps condensate out of the distribution piping instead of leaving it for traps and filters downstream to catch.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet clear air on the cooling side, keep the room out of the heat, and run the unit on its own circuit sized to the motor nameplate; at 30 HP the electrical install is worth planning before the machine arrives. Oil, oil filter and separator element are the service items. Behind the dryer, a coalescing filter protects paint and instrument air, and a condensate drain plus an oil water separator keeps the water the dryer pulls out of your floor and out of the drain line. See our \u003ca href=\"\/collections\/coalescing-air-filters\"\u003ecoalescing air filters\u003c\/a\u003e, \u003ca href=\"\/collections\/condensate-drains\"\u003econdensate drains\u003c\/a\u003e and \u003ca href=\"\/collections\/oil-water-separator\"\u003eoil water separators\u003c\/a\u003e, or browse the full \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressor\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67620368285971,"sku":"4152028471","price":22453.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-30-tank-mount-dryer-rotary-screw-air-compressor.png?v=1791544261"},{"product_id":"abac-as-30-30-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor","title":"ABAC AS-30503TMD 30 HP Rotary Screw Air Compressor - 131 Gallon Tank Mount with Dryer, 150 PSI, 103.1 CFM, 70 dBA","description":"\u003cp\u003eThe ABAC AS-30503TMD is a complete 30 HP compressed air station on one base: a rotary screw air end, a 131 gallon air receiver and an integrated refrigerated dryer, mounted, wired and plumbed together at the factory. It delivers 103.1 CFM at a 150 PSI maximum and runs at 70 dBA. There is no separate tank or dryer to size, site and pipe, so installation comes down to setting it in place, landing one electrical connection and connecting your air line. Assembled it measures 75 x 31 x 72 in and weighs 1365 lbs. Power is 208-230-460V three-phase.\u003c\/p\u003e\n\u003ch3\u003eKey specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eModel: AS-30503TMD (part number 4152028472)\u003c\/li\u003e\n\u003cli\u003eMotor: 30 HP, energy efficient\u003c\/li\u003e\n\u003cli\u003eAir delivery: 103.1 CFM\u003c\/li\u003e\n\u003cli\u003eMaximum working pressure: 150 PSI\u003c\/li\u003e\n\u003cli\u003eNoise level: 70 dBA\u003c\/li\u003e\n\u003cli\u003eTank: 131 gallon receiver, tank mount\u003c\/li\u003e\n\u003cli\u003eIntegrated refrigerated air dryer\u003c\/li\u003e\n\u003cli\u003ePower supply: 208-230-460\/3\/60\u003c\/li\u003e\n\u003cli\u003eWeight: 1365 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions (L x W x H): 75 x 31 x 72 in\u003c\/li\u003e\n\u003cli\u003eFully integrated aluminum block air end\u003c\/li\u003e\n\u003cli\u003eVertical oil separation technology\u003c\/li\u003e\n\u003cli\u003eBrand: ABAC, part of the \u003ca href=\"\/collections\/atlas-copco\"\u003eAtlas Copco group\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy 150 PSI, and what it costs you\u003c\/h3\u003e\n\u003cp\u003ePressure and flow trade against each other on the same air end. At 150 PSI this machine gives 103.1 CFM; the 125 PSI build of the identical package gives 114.1 CFM. You are spending 11 CFM of airflow, and the energy behind it every hour the compressor runs, to buy the extra 25 PSI. Buy it when something real needs the pressure: press and clamp circuits, higher pressure tooling, a shop that works at 120 PSI at the drop rather than 90, or a long distribution run where line loss eats into delivered pressure before the air reaches the tool. If every drop is regulated down to 90 or 100 PSI anyway, the 125 PSI \u003ca href=\"\/products\/abac-as-30-30-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-30253TMD\u003c\/a\u003e is the better machine and the cheaper one to run.\u003c\/p\u003e\n\u003ch3\u003eWhat the tank and dryer package changes\u003c\/h3\u003e\n\u003cp\u003eEvery rotary screw sends warm, saturated air downstream, and that water is what rusts piping, freezes air logic, pits tooling and ruins a paint finish. Solving it piecemeal means sizing a receiver, buying a dryer, finding floor space for both, then wiring and plumbing them to the compressor. On the TMD build all three arrive as one matched assembly: the receiver sits under the compressor, the dryer is mounted and wired with it, and the footprint stays 75 x 31 in rather than three machines spread along a wall. The cost is height and weight, 72 in tall and 1365 lbs, so check door clearance, the floor route and floor loading before delivery.\u003c\/p\u003e\n\u003ch3\u003eWhy a screw instead of another piston\u003c\/h3\u003e\n\u003cp\u003eA piston compressor builds air in bursts and needs time to cool between them. A rotary screw is rated for continuous duty, so it holds a flat line pressure through a full shift instead of sagging and recovering between jobs. At 30 HP that difference is the whole point: this is a machine for a plant drawing air most of the day, not one that tops up a receiver now and then. A screw dislikes short cycling, which is part of why the matched receiver matters, and it wants a demand pattern that keeps it loaded.\u003c\/p\u003e\n\u003ch3\u003eHow it compares\u003c\/h3\u003e\n\u003cp\u003eWithin the AS-B range the choices around this machine are pressure, mounting and dryer. The \u003ca href=\"\/products\/abac-as-30-30-hp-131-gallon-tank-mount-dryer-125-psi-rotary-screw-air-compressor\"\u003eAS-30253TMD\u003c\/a\u003e is the same package set for 125 PSI, trading pressure for flow at 114.1 CFM in an identical cabinet at the same 1365 lbs. If you already own a correctly sized receiver, the \u003ca href=\"\/products\/abac-as-30-30-hp-base-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-30503BMD\u003c\/a\u003e is the same 103.1 CFM air end and dryer without the tank, at 867 lbs and 55 x 31 x 49 in, and the \u003ca href=\"\/products\/abac-as-30-30-hp-base-mount-150-psi-rotary-screw-air-compressor\"\u003eAS-30503BM\u003c\/a\u003e drops the dryer as well at 759 lbs and 44 x 31 x 49 in. A step down in horsepower at the same 150 PSI, the \u003ca href=\"\/products\/abac-as-25-25-hp-131-gallon-tank-mount-dryer-150-psi-rotary-screw-air-compressor\"\u003eAS-25503TMD\u003c\/a\u003e gives 92.2 CFM at 69 dBA and 1330 lbs in the same 75 x 31 x 72 in footprint. At 103.1 CFM the AS-30 is the largest machine in the AS-B tank mount range, the one to choose when 25 HP is already running loaded most of the shift.\u003c\/p\u003e\n\u003ch3\u003eTypical applications\u003c\/h3\u003e\n\u003cp\u003eProduction and fabrication floors, machine shops running several CNC cells, automotive and fleet service bays, tire and truck shops, plasma tables, packaging lines, sandblasting, and spray finishing or powder coating where moisture in the line spoils tools, air logic or finish quality. The 150 PSI rating suits plants where the distribution run is long, where press and clamp circuits sit on the same system as handheld tools, or where a 125 PSI machine has been struggling to hold pressure at the far end of the building. At 103.1 CFM it will carry a bank of air ratchets and sanders, a continuous blow off, a blast cabinet, or several cells drawing at once through a full shift. Drying the air at the compressor keeps condensate out of the distribution piping instead of leaving it for traps and filters downstream to catch.\u003c\/p\u003e\n\u003ch3\u003eWhat to pair it with\u003c\/h3\u003e\n\u003cp\u003eGive the cabinet clear air on the cooling side so the package is not recirculating its own heat, keep the room ventilated, and run the unit on its own three-phase circuit sized to the motor nameplate; at 30 HP the electrical install is worth planning before the machine arrives. Oil, oil filter, air filter and separator element are the scheduled service items on a screw package, and keeping a spare set on the shelf stops a routine service from turning into downtime. Behind the dryer, a coalescing filter protects paint and instrument air, and a condensate drain plus an oil water separator keeps the water the dryer pulls out of your floor and out of the drain line. See our \u003ca href=\"\/collections\/coalescing-air-filters\"\u003ecoalescing air filters\u003c\/a\u003e, \u003ca href=\"\/collections\/condensate-drains\"\u003econdensate drains\u003c\/a\u003e and \u003ca href=\"\/collections\/oil-water-separator\"\u003eoil water separators\u003c\/a\u003e, or browse the full \u003ca href=\"\/collections\/rotary-screw-air-compressors\"\u003erotary screw air compressor\u003c\/a\u003e range. Call us with your tool list and duty cycle and we will confirm connection sizes and installation clearances before you pipe it in.\u003c\/p\u003e\n","brand":"ABAC","offers":[{"title":"208-230-460V 3-Phase","offer_id":67620434379027,"sku":"4152028472","price":22453.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/3141\/8387\/files\/abac-as-30503tmd-tank-mount-dryer-rotary-screw-air-compressor.png?v=1791549067"}],"url":"https:\/\/aircompressorstore.com\/collections\/abac-131-gallon-rotary-screw-air-compressors.oembed","provider":"Warthog Air Compressor Store","version":"1.0","type":"link"}